How to Reset the Maintenance Light on Suzuki Ciaz?

1 Answers
MiguelLynn
07/30/25 1:53am
Here are the detailed steps to reset the maintenance light on Suzuki Ciaz: 1. With the engine turned off, press and hold the short-distance trip meter reset button located below the tachometer. 2. Turn the ignition switch to the ON position, then release the short-distance trip meter reset button. The display will show the 'SERVICE' indicator. 3. Pull out the minute button on the clock and turn it clockwise. The mileage will appear on the display. 4. Turn off the engine to reset the reminder message. 5. Turn the ignition switch back to the ON position, and the 'SERVICE' indicator will disappear.
Was this review help?
13
4
Share
More Forum Discussions

Are the Audi A7 and Panamera in the same class?

The Audi A7 and Panamera are not in the same class. The Panamera is much more expensive than the Audi A7. However, both the Audi A7 and Porsche Panamera are relatively high-end four-door coupes. Introduction to the Audi A7: The Audi A7 is a four-door sports luxury coupe positioned between C-class executive and D-class luxury sedans. In terms of size, it is slightly larger than a non-extended C-class executive sedan but smaller than a D-class luxury sedan. Introduction to the Panamera: Panamera is the Chinese translation of Porsche's Panamera. The Porsche Panamera is a four-door, five-seat coupe. As a luxury coupe, it has quick acceleration, with the top model capable of 0-100 km/h in 3.8 seconds and a top speed of nearly 310 km/h. The mid-range models vary in acceleration from 4.2 to 5.4 seconds for 0-100 km/h, comparable to supercars.
7
4
Share

What to Do If the Interior Plastic of the Car Gets Scratched?

Here are the solutions for scratches on the car's interior plastic: 1. Generally, toothpaste is used to repair scratches on hard plastic in the car because the chemical components in toothpaste have a certain repairing effect. For light scratches, applying toothpaste and gently rubbing can remove the scratched part, and the plastic will become shiny and clean as new. 2. White vinegar can also effectively remove scratches. First, find an empty spray bottle, pour some white vinegar into it, add water, shake well, spray a few times on the scratched area, and after drying, wipe it with a dry towel. 3. Most car repair shops have specialized scratch repair sprays or repair agents. Just spray a few times on the scratched area and wipe it with a towel. If the scratch is deep, it is not recommended to handle it yourself, as deep scratches usually cannot be removed with general repairs.
16
5
Share

What is the function of halogen lamps?

Halogen lamps can replace the function of incandescent lamps, and they have a longer service life, easier brightness adjustment and control, and better color rendering of light. Because halogen bulbs have high luminous efficacy and great illumination brightness, they are suitable for occasions that require concentrated lighting. Working principle: The principle is to inject halogen gases such as iodine or bromine into the bulb. At high temperatures, the sublimated tungsten filament chemically reacts with the halogen, and the cooled tungsten will re-solidify on the tungsten filament, forming a balanced cycle and avoiding premature breakage of the tungsten filament. Therefore, halogen bulbs last longer than incandescent lamps. Impact: Many cars use traditional halogen bulbs, and more than 60% of traffic accidents occur at night or in poor weather conditions. The lighting effect of halogen bulbs is greatly reduced at night or in poor weather conditions. At this time, the driver's vision is severely affected, making them prone to fatigue, distraction, etc., and the probability of traffic accidents increases significantly.
10
5
Share

Where is the temperature sensor located on a BMW 5 Series?

The outdoor temperature sensor for the air conditioning system in the BMW 523Li is located beneath the drainage channel in the engine compartment. Temperature Sensor (temperature transducer): Refers to a sensor capable of detecting temperature and converting it into a usable output signal. Temperature sensors are the core components of temperature measurement instruments and come in a wide variety. Based on measurement methods, they can be divided into two main categories: contact and non-contact. According to sensor materials and electronic component characteristics, they are classified into thermal resistors and thermocouples. Contact Temperature Sensor: The detection part of a contact temperature sensor maintains good contact with the measured object, also known as a thermometer. Non-contact Temperature Sensor: Its sensitive element does not come into contact with the measured object, also known as a non-contact temperature measurement instrument. This type of instrument can be used to measure the surface temperature of moving objects, small targets, or objects with small heat capacity or rapid (transient) temperature changes, as well as to measure the temperature distribution within a temperature field.
11
5
Share

What is the distance between stakes in the motorcycle test?

In the motorcycle test, the distance between stakes is approximately 1.5 times the length of the motorcycle body. Purpose of the stake test: To assess the ability of motor vehicle drivers to control three-wheeled motorcycles, two-wheeled motorcycles, and light motorcycles in curve driving and turning. Precautions: When starting, do not release the clutch lever too abruptly, as this may cause a sudden start and result in failure. Also, do not release the clutch lever too slowly, as this may lead to semi-clutch engagement and failure. After fully releasing the clutch lever, do not keep your hand on the clutch lever. When stopping, do not press the brake pedal or squeeze the brake lever all the way down. It is advisable to press the pedal to about 3/5-4/5 of its full travel. Pressing (or squeezing) it all the way down may cause an excessively abrupt stop and result in failure.
3
2
Share

Can motorcycles apply for scrapping?

Motorcycles can apply for scrapping. Vehicle scrapping process: Vehicle owners applying for scrapping and renewal must fill out an "Application Form for Vehicle Modification, Transfer, Alteration, Suspension, or Scrapping" and affix their seal. Apply at the registration and acceptance counter. For vehicles that have reached the scrapping age limit, a "Vehicle Scrapping Notice" will be issued. For vehicles that have not reached the scrapping age limit but are deemed to meet the scrapping standards after inspection by the vehicle inspection counter, a "Vehicle Scrapping Notice" will be issued. The vehicle owner can choose a qualified recycling company to dismantle the vehicle with the "Notice". The recycling company will dismantle the vehicle and take photos after verifying the "Notice". The engine must be separated from the vehicle, the engine block must be broken, and the frame (chassis) must be cut. The vehicle owner must submit the "Modification Form", "XX Province Vehicle Renewal Technical Appraisal Form", "Scrapped Vehicle Recycling Certificate", and photos of the dismantled vehicle to the vehicle inspection counter for verification and signature. The license plates and certificates will be reclaimed, and the application will be submitted for approval according to regulations to complete the scrapping registration.
4
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.