How to Reset the Maintenance Light on Peugeot 508?

1 Answers
BradleyRose
07/29/25 1:13pm
The method to reset the maintenance light on Peugeot 508 is: Turn off the car's ignition switch; Press and hold the trip meter reset button on the car's instrument panel; Turn on the car's ignition switch again. When the odometer display shows the countdown to 0, the reset is successful. The Dongfeng Peugeot 508 is a high-end model introduced by Peugeot in China. Its body dimensions are 4826mm, 1855mm, 1465mm, with a wheelbase of 2815mm, and a top speed of 210km/h. The model uses 16-inch wheels, while the two high-end versions come with 17-inch wheels.
Was this review help?
3
1
Share
More Forum Discussions

What Causes the Car to Shake After Replacing the High-Pressure Fuel Pump in the New Mondeo?

Reasons for the car shaking after replacing the high-pressure fuel pump in the New Mondeo: Fuel system issues: Fuel system problems are usually caused by clogged fuel lines, leading to poor fuel supply, manifested as engine shaking, unstable idling, and stalling while driving. Additionally, fuel pump failure can also cause engine shaking. To diagnose fuel pump issues, disconnect the fuel line and check the flow rate and velocity of the fuel. Electrical issues: Check if the ignition timing is accurate, as irregular ignition is often a timing issue. Inspect whether the spark plugs are worn out, if the gaps are uniform, and if the gaps have changed. Also, malfunctioning of the distributor can lead to engine shaking. Mechanical reasons: Check the engine's operating condition for any abnormal sounds, such as valve noises. Inspect the belt's working condition to see if it is loose.
3
1
Share

Does the Audi Q8 burn engine oil?

Audi Q8 burning engine oil is an individual case, not a common situation. When a vehicle experiences engine oil burning: The engine's valve guide wears unevenly and the valve oil seal ages, creating gaps that allow engine oil to enter the combustion chamber and burn. Causes of engine oil burning in cars: Front and rear crankshaft oil seals aging, excessive piston clearance, clogged air filter, leaking valve oil seals, and insufficient sealing. Consequences of engine oil burning: This leads to incomplete combustion of gases in the engine's combustion chamber, resulting in increased carbon deposits, reduced vehicle power performance, sluggish acceleration, increased fuel consumption, and more severe exhaust emissions that may even exceed standards. It also increases the owner's financial burden. The engine piston rings can become stuck due to carbon deposits, losing their oil-scraping function and worsening the oil burning. Additionally, engine lubrication becomes insufficient due to oil burning, potentially causing engine damage, severe cases may lead to cylinder scoring or complete engine failure.
19
5
Share

What are the causes of the circuit fault in cylinder 1 injector of Audi A4?

Audi A4 cylinder 1 injector circuit fault causes: 1. Injector malfunction, 2. Wiring fault, 3. Engine control module fault. It is recommended to focus on checking the connector of cylinder 1 injector, whether the connector pins are loose, or the terminals inside the connector are enlarged or loose, which would result in poor contact even if the connector is properly plugged in. Injector introduction: It is a vacuum-operated valve used in turbocharged or centrifugal supercharged vehicles, designed to release excess pressure in the intake system when the throttle valve is opened or closed. The released air pressure is recirculated back to the normal-pressure intake port before the turbocharger and after the mass airflow sensor. Working principle: The injector valve is connected to the intake manifold behind the throttle valve plate via a vacuum tube. When the throttle valve is closed, vacuum is generated in the intake manifold behind the plate, which "sucks" the injector valve open. The excess pressure from the turbocharger is vented to the atmosphere or recirculated upstream to the compressor inlet of the intake system.
12
0
Share

What is the fuel consumption per 100 kilometers for the Chery A1?

Chery A1's fuel consumption per 100 kilometers is 5.2—8.97L/100km. How to calculate car fuel consumption: Fill up the car's gasoline tank completely and reset the odometer to zero. After driving for a period of time, refill the tank and note the amount of gasoline added. Then, divide the amount of gasoline added by the distance traveled to get the fuel consumption per kilometer. Reasons for high fuel consumption: The driver's skill level, improper gear shifting and excessive braking during driving can artificially increase engine power loss. Additionally, frequent braking leads to more starts, as fuel consumption is very high during starts. Driving at low temperatures: cars require the engine to operate at normal temperatures. If the car is driven without preheating, the engine remains at a low temperature, resulting in poor fuel atomization and incomplete combustion.
6
5
Share

What is Audi called in Taiwan?

Audi is called Audi in Taiwan. BMW is directly called BMW. Audi model series: Audi's main mass-produced model series include the A series (covering AO, A, B, C, and D class models), Q series, R series, TT series, S series, RS series, and the Allroad series derived from the A series. Audi logo: The logo of Audi cars consists of four rings, representing the four companies before the merger. These companies were originally manufacturers of bicycles, motorcycles, and passenger cars. Since the company was formed by the merger of four companies, each ring symbolizes one of the companies.
2
2
Share

Why does the Baojun 730 central control lock automatically?

Baojun 730 central control automatic locking is the activation of the automatic locking function. Advantages and disadvantages of automatic locking: Advantages: It provides protection for passengers with children in the car, preventing young children from opening the door handle while the car is in motion. Disadvantages: It may hinder escape in emergencies because the doors are harder to open. Therefore, it is necessary to consider both your needs and safety comprehensively. How to activate the automatic locking function: Put the gear in P position, turn the key to the ON position, and ensure all four doors are closed. Then press the lock button, and when you see the hazard warning lights flash twice on the dashboard, the function is activated.
11
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.