How to reset the maintenance light on Peugeot 3008?

What are the three inspections for vehicles?

Vehicle three inspections refer to the following aspects: 1. Pre-driving inspection: (1) Check if the lights and turn signals are working properly. (2) Check if the braking system is functioning well, including the brake, brake fluid level, and brake tail light. (3) Check the fuel level. (4) Check if the rearview mirror is properly positioned. (5) Check if the headlights, tail lights, brake lights, and windshield are clean. (6) Check if the tire pressure and tire condition are normal. (7) Check if the engine oil level meets the requirements. (8) Check if the wipers and windshield washer fluid level and operation meet the requirements. (9) Check if the exposed bolts and nuts on the vehicle are complete. (10) Start the engine and check if it is running normally, if there are any abnormal noises, and if all gauges and warning lights are working properly. 2. Mid-drive parking inspection: (1) Check if the engine and chassis are working normally. (2) Check if all gauges are functioning effectively and reliably. (3) Check if the steering system, hand brake, and clutch are working normally and reliably. (4) Check the tire pressure and remove any debris from the tire treads. (5) Check for any leaks of water, oil, or gas. (6) Inspect the entire vehicle exterior for any abnormalities. 3. Post-driving inspection and maintenance: (1) Check if the engine is running normally and listen for any gas leaks. (2) Check and refill fuel, engine oil, and coolant. (3) Inspect and lubricate the designated lubrication points as required. (4) Turn the oil filter handle 3-4 times. (5) Feel the brake drum to check if it is overheated. (6) Check if the tire pressure is sufficient. (7) If the temperature is below zero and the cooling system does not have antifreeze, drain the coolant completely. (8) In extremely cold regions, store the battery in a warm room. (9) Turn off all switches and knobs. (10) Check and ensure all onboard tools and accessories are complete.

7

1

Share

Why is the Iveco blower not working?

Iveco blower not working may be due to its own failure, possibly burned out or poor switch contact. The following is relevant information about Iveco trucks: 1. Nanjing Iveco Automobile Co., Ltd.: Nanjing Iveco Automobile Co., Ltd., abbreviated as NAVECO, was established on March 1, 1996. It is a Sino-foreign joint venture jointly invested by Nanjing Automobile Group Corporation and Italy's IVECO S.p.A. 2. Products of Iveco Automobile Co., Ltd.: The company's products are divided into two major platforms: IVECO and Yuejin. The IVECO brand has a design capacity of producing 60,000 Iveco series light vehicles and 75,000 diesel engines annually. The products mainly include four major series: passenger cars, trucks, travel vehicles, and off-road vehicles, covering 3.5 to 6 tons with 7 tonnage levels and 7 wheelbases, including over 200 models such as light buses, trucks, military off-road vehicles, medium-sized buses, and various modified special-purpose vehicles.

5

2

Share

Why is there water dripping under the car when the air conditioner is on in summer?

The reason for significant water dripping under the car when the air conditioner is on: It is condensation water caused by the operation of the air conditioner, which is a normal phenomenon related to the principle of the air conditioner. The specific reasons for significant water dripping under the car when the air conditioner is on are as follows: 1. Evaporator configuration: Since the car's cooling system is equipped with an evaporator inside the dashboard, when the air conditioner is on, the surface temperature of the evaporator is very low. The moisture in the hot air inside the car will condense on the surface of the evaporator's heat-absorbing fins and be collected by the plastic casing of the evaporator. 2. Compressor: Sometimes, the exterior of the compressor installed in the engine compartment may also condense moisture from the air, causing water to drip onto the ground. 3. Lack of insulation foam: If the low-pressure pipeline is not wrapped with insulation foam, the surface of the pipeline is prone to condensing moisture from the air, and water droplets often condense and accumulate at the lowest point of the pipeline, dripping down.

18

1

Share

How to Unlock a Stuck Automatic Transmission P Gear?

Specific steps are as follows: 1. Release the brake pedal, press it again, and then try to shift gears. 2. Slightly turn the steering wheel and then try to shift gears. 3. Restart the engine, press the brake once more, and then try to shift gears. 4. Open the hood, disconnect the battery, and then reconnect it. Restart the engine, press the brake once more, and then try to shift gears. Reasons for P gear lock: 1. When parking, the P gear was engaged before the car came to a complete stop. 2. When the vehicle is parked on a slope, the P gear is engaged first, and then the pedal is released. At this time, the vehicle will slide slightly forward due to its own weight, automatically eliminating the gap of the P gear lock teeth. Both of the above situations can cause the gear lever to get stuck, making it impossible to shift to other gears. In addition, damaged brake light switch, damaged gear shift mechanism, and damaged transmission control unit are common causes of automatic transmission P gear lock.

13

4

Share

What are the reasons why an automatic transmission car doesn't move when pressing the accelerator in D gear?

If your vehicle doesn't move after shifting to D gear and pressing the accelerator, it is likely caused by the following reasons: 1. Sensor signal error: When the transmission shift valve position sensor signal is incorrect, the vehicle cannot detect which gear it is in. 2. Shift valve problem: The gear is not engaged properly, and the oil passage cannot open. 3. Transmission failure: The transmission solenoid valve or electronic module is malfunctioning. 4. Oil level issue: The transmission oil level is too low, or the internal oil pressure is too low. 5. Brake lock-up: This prevents the wheels from moving forward, and pressing the accelerator may produce abnormal noises. 6. Handbrake problem: The handbrake is not released or not fully loosened.

15

4

Share

What does Volvo Care Key mean?

Volvo Care Key refers to a feature that allows the car owner to set certain restrictions on the vehicle's characteristics, which are designed to promote safe driving. The owner can use the Care Key to set speed warnings and determine the maximum volume of the vehicle's speaker system. Additionally, some functions of the car's driver support system will remain constantly activated. Extended information: The role of the Volvo Care Key: With the Volvo Care Key, the owner can set the vehicle's maximum speed and other restrictions at any time. This way, if the vehicle is driven by other family members or friends, the owner can further regulate the driver's behavior to prevent accidents and injuries caused by excessive speed.

2

1

Share

How to reset the maintenance light on Peugeot 3008?

What are the three inspections for vehicles?

Why is the Iveco blower not working?

Why is there water dripping under the car when the air conditioner is on in summer?

How to Unlock a Stuck Automatic Transmission P Gear?

What are the reasons why an automatic transmission car doesn't move when pressing the accelerator in D gear?

What does Volvo Care Key mean?

Is the Vios a domestic or joint-venture car?

What does the wheelbase of a car mean?

Which One is the Car Power Switch?

How many kilometers can a car run on a full tank of gas?