How to reset the maintenance light on GAC Trumpchi GS4?

How to Connect Bluetooth to Play Music in GL8?

First, enter the car's Bluetooth interface, then click on 'Pair' in the Bluetooth interface to make the Bluetooth enter pairing mode. Turn on your phone's Bluetooth device, search for new Bluetooth devices, and connect to the car's Bluetooth device once found. After entering the pairing password, 'Connected' will be displayed on the car's Bluetooth.

17

3

Share

Does the dash cam record when the car is turned off?

There are two types of dash cams: one that cannot record after the car is parked, and another that remains on standby after the car is turned off. If the vehicle experiences any vibration, it will immediately start recording. 1. A dash cam that draws power from the reading light or other constant power source will continue to work even after the car is turned off. In simple terms, it operates 24/7, which means the dash cam continuously draws power, potentially draining the car battery. This could result in insufficient power to start the engine the next time. 2. The scenario where the dash cam continues to work after the car is turned off involves the dash cam having a parking monitoring and motion detection feature. This function requires the dash cam to have a built-in battery or to be connected to the ACC fuse for power. After the car is turned off, it automatically enters parking monitoring mode, where the sensor continuously monitors the vehicle's condition. If any anomalies or vibrations are detected, it automatically records the monitoring video and saves it separately. 3. Compared to drawing constant power, a dash cam with parking monitoring connected to the ACC fuse is more power-efficient and has less impact on the car battery. However, if the car is left unused for several days, it could still lead to battery drainage and difficulty starting the engine.

14

1

Share

How to Remove the Headlight Switch of a Volkswagen?

Car light switches are generally integrated into the stalk-type switch located on the left side of the steering wheel. For Volkswagen models, when the switch is in the off position, press it inward slightly with some force, then rotate it clockwise a bit, and finally pull it outward as a whole to remove it.

7

4

Share

How to Remove the Rear Seat of Lavida?

To remove the seat cushion, generally place your hands under the bottom of the seat cushion and lift it upwards, then flip the lifted seat cushion forward. Push the connecting shafts at both ends towards the middle to release the metal shafts from the clips, and the seat cushion can then be removed. To fold down the seat back, lift the switches on both sides of the backrest, then use your hands to pull it forward.

11

1

Share

How to Check if a Car Compressor is Working Properly?

By observing the pressure, turn on the air conditioning, and the low-pressure side gauge should drop. If it does not drop or drops very little, the compressor can be determined to be faulty. Disconnect the compressor's low-pressure pipe, block the rear end of the high-pressure side pipe fitted with a pressure gauge, and then increase the engine speed to about 2000 RPM. At this point, the compressor's high-pressure side pressure should be around 1.5MPa, and there should be no significant change in pressure after the engine is turned off. Otherwise, the compressor can be determined to be faulty.

3

2

Share

What Lights Should Be Used When Driving on the Highway at Night?

When driving on the highway at night, you should turn on the width indicator lights, high and low beam headlights, and turn signals. Below is a detailed introduction to the use of lights on highways: 1. Width indicator lights. When driving at night, whether on the highway or ordinary roads, the width indicator lights must be turned on. These are small lights that, when activated, illuminate the front and rear width indicator lights as well as the rear license plate light. 2. High and low beam headlights. You can use high beams when driving on the highway at night, but it's important to use them appropriately. If the distance to the vehicle ahead is large, exceeding 150 meters, you can use high beams; when the distance decreases, you should switch to low beams. When meeting another vehicle on the highway, if the central divider can completely block the light, you can keep the high beams on; but if grass, roadside trees, or metal railings cannot fully block the light, you should switch to low beams when the distance between the two vehicles is 150 meters. 3. Turn signals. Turn signals must be used when changing lanes, overtaking, entering, or exiting the highway on the highway, and you should only change lanes after ensuring it is safe to do so, to prevent vehicles behind or in adjacent lanes from reacting in time.

13

5

Share

How to reset the maintenance light on GAC Trumpchi GS4?

How to Connect Bluetooth to Play Music in GL8?

Does the dash cam record when the car is turned off?

How to Remove the Headlight Switch of a Volkswagen?

How to Remove the Rear Seat of Lavida?

How to Check if a Car Compressor is Working Properly?

What Lights Should Be Used When Driving on the Highway at Night?

How to Conduct Annual Inspection for Vehicles After the Six-Year Exemption Period?

Are Adaptive High Beam Headlights Good?

How to Turn Off the Interior Light in a Car?

How to Cancel the Maintenance Reminder on Lavida?