How to Reset the Maintenance Light on GAC Mitsubishi?

1 Answers
DiAlejandro
07/30/25 9:27am
Insert the car key, close the door, and start the car. Operate the trip odometer reset info button to display the warning cycle value on the odometer. The maintenance reminder light will start flashing. Press the info switch again while it's flashing, and the display will change to 'clear'.
Was this review help?
5
2
Share
More Forum Discussions

What are the safe capacity and actual capacity of a fuel tank?

The rated volume stated in the vehicle's user manual is the safe capacity, and it is normal for the actual capacity to be 10% larger than the rated volume. There are three methods to reduce fuel consumption in vehicles: Minimize the vehicle's weight: Keep the interior as simple as possible and avoid carrying unnecessary items, as every additional kilogram of load increases fuel consumption by 1%; Avoid excessive modifications: Adding spoilers, protective covers, or wings can disrupt the original aerodynamic design of the vehicle, increasing wind resistance and consuming extra fuel. Modifying lighting systems can also increase electrical load, leading to unnecessary fuel consumption; Develop good driving habits: Avoid sudden acceleration, driving at high speeds in low gears, prolonged idling, frequent lane changes or braking. Instead, aim for smooth starts, steady-speed driving, and reduced braking.
17
3
Share

What sound does a bad wheel bearing make?

Sounds of a damaged wheel bearing: 1. Squeaking: When turning the steering wheel while stationary or at low speeds, a "squeaking" sound may occur, and in severe cases, steering wheel vibration can be felt. 2. Humming: While driving, tire noise becomes noticeably louder, and in severe cases, a "humming" sound may be heard. 3. Thumping: When driving on bumpy roads or over speed bumps, a "thumping" sound may be heard. The following is an introduction to wheel bearings: 1. Definition of wheel bearings: They are components used at the axle of a car to bear weight and provide precise guidance for the rotation of the hub, bearing both axial and radial loads. They are an important part of the car's load-bearing and rotation. 2. Composition and installation of wheel bearings: Traditional automotive wheel bearings consist of two sets of tapered roller bearings or ball bearings combined. The installation, greasing, sealing, and adjustment of bearing clearance are all carried out on the automobile production line.
16
3
Share

What is the method for transferring a motorcycle license plate?

To transfer the ownership of a motorcycle that already has a license plate, you must first obtain the "Second-hand Vehicle Transaction Invoice" and then proceed to the local vehicle management office to complete the transfer. Below is a detailed introduction to the motorcycle ownership transfer process: 1. Required documents: Proof of the motor vehicle's origin; the whole vehicle factory certificate of conformity for domestically produced motor vehicles; proof of payment or tax exemption certificate for the motor vehicle purchase tax. Proof of compulsory motor vehicle traffic accident liability insurance; technical data file of the motor vehicle; "Motor Vehicle Registration, Transfer, Cancellation/Transfer Application Form," etc. 2. Proxy: If handled by an agent, the original and copy of the agent's identity certificate must also be submitted (if the agent is a unit, the original and copy of the handler's identity certificate must also be submitted), along with a written authorization from the motor vehicle owner.
5
2
Share

What to Do When a White Car's Paint Gets Scratched?

Solutions for scratches on a white car's paint: 1. Polishing: Polishing is only suitable for minor scratches. Moderate friction helps eliminate fine scratches, but excessive polishing can thin the paint and eventually wear it through. 2. Touch-up painting: For deeper scratches, if the area is small and you have good DIY skills, you can do the touch-up yourself. For larger scratches, it's recommended to visit a 4S shop for professional repair. Steps for touch-up painting: 1. Clean the scratch before repair, using 800-grit sandpaper and a sanding block to smooth the scratch. 2. If the scratch is deep, use filler to level it. 3. After the filler dries, use 800-grit sandpaper and a sanding block to smooth the scratch again, then wipe it clean with a towel. 4. Gently sand the surrounding area with 2000-grit sandpaper until it becomes matte, then clean it. 5. Use a cleaning pad to wipe around the scratch before applying touch-up paint, then spray with clear gloss varnish.
16
5
Share

Differences Between Haval H6 and M6

There are many differences between the Haval H6 and M6. The following introduces the distinctions between the two models: 1. Exterior: The Haval M6 features a bold and expressive design, while the Haval H6 offers two versions with red and blue logos. The red logo version embodies the luxurious and classic side of Haval, whereas the blue logo version showcases a cool and trendy style, primarily targeting younger consumers. 2. Powertrain: The Haval M6 is equipped with the older 1.5T turbocharged engine from the previous H6, whereas the all-new Haval H6 comes with the latest direct-injection turbocharged engine, available in 1.5T and 2.0T displacements. The 1.5T version also delivers significantly higher power output compared to the older 1.5T engine.
13
4
Share

How Long Should You Rest When Tires Are Hot to the Touch?

Tires that are hot to the touch need to rest for about an hour. Here is some related information: 1. Replacement Time: Tires should be replaced every 3 years. If a vehicle is driven 20,000 kilometers a year, consider replacing them in 2 to 3 years. If driven around 10,000 kilometers a year, replacement should be considered in 4 to 5 years. 2. Function: Tires are often used under complex and demanding conditions, enduring various deformations, loads, forces, and high and low temperatures while driving. Therefore, they must have relatively high load-bearing, traction, and cushioning performance. Additionally, they need to have high wear resistance and flexibility, as well as relatively low rolling resistance and heat generation. 3. Classification: Tires can be categorized by their use into: passenger car tires, light truck tires, truck and bus tires, construction machinery tires, off-road vehicle tires, and agricultural and forestry machinery tires.
19
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.