How to reset the maintenance light on Citroen C4L?

2 Answers
VanJuliette
07/30/25 2:04am
Citroen C4L maintenance light reset method: 1. Turn off the ignition switch of the C4L. 2. Then press and hold the mileage reset button. 3. After turning on the ignition switch, you will see the odometer start counting down. 4. When the display shows "=0" and the maintenance light goes off, it means the maintenance indicator has been successfully reset. Below are the benefits of car maintenance: 1. Regular car maintenance can improve the performance of the car and extend its service life. 2. Save fuel. According to relevant car maintenance test programs, proper car maintenance can save 11.36% of fuel during driving. 3. Reduce emissions. The same car maintenance test program shows that after overall maintenance, the CO emissions of the car during idle driving are reduced by 45.37%.
Was this review help?
1
4
Share
VonJoanna
08/15/25 8:03am
I've been driving my Citroen C4L for three or four years now, and I've tried the method to reset the maintenance light several times myself—it's quite convenient and quick. The basic steps are: first, sit in the driver's seat, turn the engine off completely, and turn the key to the OFF position; then press and hold the small mileage reset button on the dashboard, which is usually located near the speedometer; next, turn the key one notch to ACC without starting the engine, and the dashboard will light up; continue holding the button without releasing it for about 10 seconds, and the screen will start flashing numbers or display a countdown, like a little animation. When it stops and shows a steady '000' or resets, you can release the button, and the light will go off. The whole process takes less than half a minute, but you need a good memory and steady hands. Actually, the maintenance light is just a reminder for us to schedule regular maintenance, like changing the oil or checking the brakes. The light going off doesn’t mean you can skip maintenance—it’s best to follow the manual’s guidelines. Last time I got lazy and delayed it once, and I noticed the engine noise got louder—I regretted it immediately, so timely maintenance is crucial. Keeping this habit in daily driving can also extend the car’s lifespan.
Was this review help?
18
2
Share
Expand All
More Forum Discussions

How to solve the high water temperature issue of CFMOTO 650MT?

Installed radiator guard mesh, it is recommended to remove it, because the 650MT is a road-oriented ADV, the radiator is not so easily damaged, and the guard mesh may actually affect heat dissipation. You can try replacing it with a higher-grade coolant.
4
2
Share

What to Do When the Electric Bike Key Won't Turn?

Turn the handlebar to the left to find a certain angle, then try turning the key while adjusting the handlebar to make it turnable, or apply lubricating oil to the lock cylinder. Twist the key to rotate the handlebar several times to adjust its position. If the key is inserted but won't turn or is not flexible.
11
5
Share

How to Quickly Bleed Air from a Manual Grease Gun?

Unscrew the grease gun nozzle to separate it from the barrel. Lock the locking tab at the rear of the barrel and push the handle at the barrel end all the way in. Submerge the open end of the grease gun into the grease bucket to a depth of about 30 mm, then pull the handle at the barrel end to draw grease into the tube. Reattach the grease gun nozzle, hold the locking mechanism at the barrel end, and push the follower handle to begin bleeding air. Use your fingertip to control the air vent until grease emerges from the vent, indicating that the air has been fully bled.
1
5
Share

How long does it take to charge the battery by idling after jump-starting?

After jump-starting, it takes about 2 to 3 hours to charge the battery by idling. Idling can help charge the battery. The functions of the battery: 1. Power the engine starting system, ignition system, and supply electricity to the car; 2. Provide power to the car's electrical equipment when the engine is stopped or at low idle speed; 3. Participate in power supply when the electrical demand exceeds the generator's supply capacity; 4. Act as a voltage stabilizer for the entire vehicle's electrical system, mitigating impact voltage in the electrical system and protecting the car's electronic equipment. Methods to check if the battery has power: 1. Check the battery's charge indicator; 2. Measure the battery's static voltage; 3. Check the battery fault light; 4. Observe if the dashboard flickers or dims when starting the car; 5. Check if the battery shows signs of bulging, deformation, oxidation, or leakage.
1
1
Share

How to Install Anti-Collision Strips and Corner Guards?

For adhesive-type anti-collision strips, they are generally applied to the most vulnerable areas of car doors where impacts are likely to occur. The cross-section of strip-type protectors is U-shaped, with double-sided tape attached to the inner side of the U. During installation, the U-shaped groove should be fitted onto the edge of the car door.
8
4
Share

How to Open a Car Detailing Shop?

Starting a business, especially for beginners, can have a very low success rate if you don't understand market trends, so thorough preparation is essential. You need to learn relevant car detailing techniques and master some methods for managing a car detailing shop. A good system can prevent bad people from acting recklessly, while a bad system can prevent good people from fully doing good deeds, or even push them in the opposite direction.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.