How to reset the maintenance light on an Audi Q5?

3 Answers
VanSamantha
07/29/25 3:36pm
Open the MMI system menu, click the "CAR" button, select "Maintenance and Inspection" by rotating the knob, press the knob to confirm and enter the next submenu. Under the "Maintenance and Inspection" submenu, select "Maintenance Interval," press the knob to confirm and enter the next submenu, then follow the prompts to reset the maintenance interval to complete the maintenance light reset. Introduction to the Audi Q5: 1. Exterior: It features 19-inch fan-blade-style wheels, which, compared to the 20-inch wheels of the gasoline version, are less luxurious and imposing but more technologically advanced. 2. Powertrain: It is equipped with a 2.0T engine and an 8-speed automatic transmission.
Was this review help?
11
2
Share
McSienna
08/14/25 9:21am
I previously encountered the situation where the maintenance light on my Audi Q5 came on, and resetting it was quite straightforward. After turning off the engine, I located the small button on the dashboard, held it down, and then turned the key to the ignition position without starting the engine. After waiting for about ten seconds, when the wrench icon or service prompt appeared on the screen, I released the button, and the indicator light went off. This method works for most models, but I was a bit nervous the first time I did it, fearing I might make a mistake, but it went smoothly. After resetting the maintenance light, the system can accurately remind you of the next service time. If left unattended, the car will keep prompting, which can be distracting while driving. I also recommend checking the owner's manual because the button location might vary for different model years of the Q5—for example, older models have the button on the right side of the steering wheel, while newer ones have it on the left. In short, doing it yourself saves time and effort, and you'll get the hang of it after a few tries.
Was this review help?
5
0
Share
Expand All
KendraRose
10/12/25 2:48am
I often maintain my Audi Q5 myself and am very familiar with resetting the maintenance light. After turning off the ignition, press and hold the reset button on the dashboard, then turn the power to the running position without starting the engine. Wait a few seconds until the service icon flashes, then release the button, and the maintenance reminder will disappear. The button location varies by model: newer models may have it on the steering wheel controls, while older models require accessing the settings menu. When I DIY, I keep a small notebook to jot down the steps to ensure success on the first try. If I accidentally press the wrong button, restarting the car usually resolves the issue. This method helps avoid unnecessary trips to the dealership and ensures the system accurately tracks the next service. Remember to perform regular maintenance—resetting the light gives peace of mind when driving. The process is quick, but always check the vehicle manual for details. Give it a try—it’s easy and practical.
Was this review help?
14
2
Share
Expand All
More Forum Discussions

How to Solve the Engine Immobilizer Authentication Failure Issue on Baojun 510?

Fellow car owners should first check their car keys. The remote key fob contains a dedicated module specifically for engine starting. Simply pry open the casing, remove the old battery and replace it with a new one.
8
1
Share

How to Remove the Fuel Pump on a Buick Excelle?

First remove the rear seat to expose a black metal cover secured by four screws. Unscrew these to reveal the fuel pump. Disconnect all wiring connections, then use a specialized fuel pump removal tool to unscrew and extract the unit.
9
1
Share

How to fix the peeling dashboard of a Buick Excelle?

If the dashboard warping issue occurs during the car's warranty period, you can contact after-sales service for relevant handling. If the car's warranty period has expired but the dashboard warping issue occurs, you can go to an auto repair shop for handling.
13
2
Share

What Causes the ABS Light to Illuminate in a Jaguar?

ABS light illumination can occur in various states, with different causes and solutions for each state, as detailed below: State 1: ABS warning light remains constantly lit (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the contaminants from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal operation. Cause 2: Poor signal transmission due to loose system wiring connections or poor contact in the ABS relay, leading to system malfunction. Solution: Inspect wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple electrical components are in use, the battery voltage drops below 10.5V. As engine speed increases, voltage rises, and the ABS light turns off. This may also occur due to insufficient power supply voltage to the ABS system, such as poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains lit after engine startup until the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor electrical connector contact in the ABS hydraulic valve body; ABS control unit malfunction. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check for enlarged connector gaps; replace the ABS or ABS/ASR control unit. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS control unit detects a significant discrepancy between rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's specified tire and wheel rim specifications, typically listed on the fuel tank cap sticker. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and manually push the brake switch linkage fully downward, then release the pedal to complete self-positioning; replace the brake light switch if necessary. If the ABS warning light is illuminated, it is advisable not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.
17
1
Share

How to adjust the ambient lighting in the 2021 Audi A6L?

You can adjust the interior ambient lighting through the MMI display. Press the CAR button to select the system and enter the background lighting interface. The ambient lighting at the front footwells, rear footwells, front door panels, and rear door panels can all be set via the MMI.
2
0
Share

How to Repair Cracked Leather in Car Interior?

Use a soft brush and a slightly damp towel to thoroughly clean the leather that needs repair or has wrinkles. Sand the leather surface that requires repair with water sandpaper, and remove any already cracked leather as well. Apply leather repair paste to the surface that needs fixing, spray a layer of primer on the leather surface, then complete the coloring within 60-150 seconds.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.