How to reset the maintenance light on a 2020 Corolla?

2 Answers
DeMalachi
07/24/25 10:38am
Press and hold the "A" button, step on the brake pedal, and do not release either of them during the process. Do not start the engine, but the vehicle's power must be turned on. When the characters on the instrument panel flash or the entire display screen flashes, continue to hold the "A" button, and "..." will appear on the instrument panel. Release the reset button "A" and the brake pedal. The maintenance light reset operation is now complete. Turn off the vehicle's power.
Was this review help?
13
5
Share
CarolineLynn
08/11/25 5:42am
When the maintenance light comes on, I always check the service records first to confirm the maintenance is done before resetting it. The 2020 Corolla makes it simple: turn off the engine, switch the key to the ON position without starting the engine, press the DISP button on the steering wheel a few times to enter the instrument menu, find the maintenance reset option, and hold the OK button for a few seconds. The whole process requires no tools and takes just minutes. Resetting ensures the next reminder is accurate, avoiding delays in actual maintenance. It's recommended to reset regularly along with routine checks like tire wear or brake pads, as keeping the car in good condition saves on major repairs and ensures safer driving.
Was this review help?
11
3
Share
Expand All
More Forum Discussions

What does 1.2t mean?

1.2t represents a turbocharged engine with a displacement of 1.2 liters. The function of the engine is to convert the heat energy of gasoline or diesel into mechanical energy by burning the expanding gas in a sealed cylinder to push the piston to do work. The components of the engine are: 1. Valve train; 2. Crankshaft connecting rod mechanism; 3. Ignition system; 4. Cooling system; 5. Lubrication system; 6. Supply system. The maintenance items for the engine include: 1. Regularly change the engine oil and oil filter; 2. Keep the crankcase well ventilated; 3. Regularly clean the crankcase; 4. Regularly clean the fuel system; 5. Regularly maintain the water tank; 6. Maintain and clean the fuel system.
9
4
Share

Should an automatic transmission car be parked by shifting to P gear first or by pulling the handbrake first?

For an automatic transmission car, it is safer to pull the handbrake first when parking, achieving the braking effect of the braking system, and then shift to P gear to lock the transmission shaft. The correct method for parking an automatic transmission car is: 1. Press the brake pedal to slow down and stop; 2. After coming to a complete stop, shift into N gear; 3. Tighten the handbrake; 4. Release the foot brake and confirm the vehicle is stationary; 5. Press the foot brake again and shift into P gear; 6. Turn off the engine. The correct method for starting an automatic transmission car is: 1. Connect the power supply, then start the car; 2. After ignition, press the brake pedal, shift into D gear, release the handbrake, and gently press the accelerator to start; 3. After starting, accelerate appropriately according to road conditions.
20
1
Share

Will the car lock if the key is inside?

If the key is left inside the car, the vehicle will lock itself. After the engine is turned off, if the doors are closed without taking the key out, both the doors and the trunk will automatically lock after a few minutes. This feature is designed to prevent the owner from forgetting to lock the car. The functions of a car key include: 1. Automatically closing the windows after turning off the engine; 2. Making it easier to locate the car in a parking lot; 3. Automatically opening the trunk; 4. Remotely opening the windows. Methods for maintaining a car key: 1. Avoid frequently placing it with metal objects; 2. Do not store the spare key in the car door; 3. Prevent the smart key from falling or being impacted; 4. Avoid exposing the smart key to high temperatures or contact with liquids; 5. Do not place the key near electronic devices.
17
1
Share

When must the timing belt be replaced?

The timing belt must be replaced approximately every 3 to 5 years or 80,000 to 100,000 kilometers. The specific replacement time depends on the actual usage condition of the vehicle. The functions of the timing belt are: 1. To drive the valve train of the engine; 2. To ensure the engine's intake and exhaust valves open and close at the appropriate times; 3. To guarantee the engine cylinders can properly intake and exhaust air. The method for replacing the timing belt is: 1. Lift the vehicle and remove the right front wheel fender liner; 2. Remove the alternator belt and the alternator belt tensioner; 3. Loosen the crankshaft pulley screw; 4. Open the engine hood and remove the water reservoir; 5. Remove the engine mounting bracket and the protective cover on the timing belt; 6. Unscrew the alternator mounting screw and remove the alternator; 7. Remove the cylinder block mounting bracket and take off the crankshaft pulley; 8. Rotate the crankshaft to the top dead center position of the cylinder and mark it; 9. Remove the timing belt and the timing tensioner to complete the replacement.
9
1
Share

Does a new car come with a spare tire and tools?

New cars come with a spare tire and tools. The spare tire is located in the trunk and there is only one. In case of a flat tire, you can use the corresponding tools to replace it. The steps to use the spare tire are as follows: 1. Prepare the tools for changing the spare tire, including a wrench and a jack; 2. Place the jack under the car—there are designated slots for the jack on the underside of the car; 3. Remove the flat tire. While installing the spare tire, the jack may shift, so be sure to place the removed tire under the car to reduce the risk of accidents; 4. Tighten the lug nuts. First, screw in one nut, then tighten all of them. Typically, the number of turns should be the same to ensure even force distribution; 5. Slowly lower the jack, remove it, and let the car settle steadily on the ground.
3
3
Share

What materials are needed for car registration?

The materials required for car registration include the purchase invoice (provided by the 4S store, with four copies: invoice copy, tax declaration copy, registration copy, and deduction copy), vehicle information form (provided by the 4S store), vehicle factory certificate (provided by the 4S store), compulsory insurance policy, original ID card of the owner, original ID card of the agent (if applicable), and the purchase quota confirmation notice. Below is the process for car registration: Drive to the inspection area: Drive to the vehicle management office. If you are using an agent, first go to the window to find a temporary worker to copy a blank power of attorney. If you are handling it yourself, drive directly to the inspection area. Pay the purchase tax: You need to go to the purchase tax collection office to pay the purchase tax. The 4S store usually also provides a purchase tax payment service, which is more convenient. After paying the tax, you will receive a vehicle purchase tax payment certificate. Vehicle license plate: After arriving at the vehicle management office and filling out the motor vehicle registration application form, the staff will first take photos of the vehicle. Vehicle stamping: The engine number and frame number of the vehicle will then be stamped for identification purposes. Vehicle inspection: Nowadays, most household passenger vehicles are exempt from inspection. If the vehicle is not exempt, it will need to undergo inspections for power, lights, exhaust, brakes, etc. Criminal investigation: Fill out the criminal investigation vehicle inspection data collection form in the criminal investigation inspection room, then submit the stamped numbers and the collection form to the counter staff for data entry. You will receive a criminal investigation vehicle inspection notice from the public security bureau. Vehicle verification: To confirm that the collection form matches the vehicle information, the staff will open the engine hood again to compare the engine number and frame number. Number selection: After all the data has been entered, you can then select a license plate number. Number selection can be done through methods like 10-choose-1 or online. If you choose the 10-choose-1 method, you can get the license plate on the same day. If you choose the online method, you will need to wait a few days to collect it or opt for express delivery to your home, where you can install the license plate yourself. During this period, you will need to apply for a temporary license plate to drive legally. Installation: After selecting the number, the next step is the installation of the motor vehicle license plate. After the new car is registered, you can receive the vehicle license, vehicle registration certificate, and qualification mark. Take the vehicle license and registration certificate to the environmental label window to print the environmental label. After obtaining the environmental label, you can purchase the vehicle and vessel tax. At this time, you will need the original vehicle license, original registration certificate and a copy, original ID card, and purchase invoice and a copy.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.