How to reset the fuel gauge on the Lynk & Co 03?

1 Answers
AniyahLee
07/30/25 10:16am
The method to reset the fuel gauge on the Lynk & Co 03 is: 1. Turn on the power; 2. Press the small square button on the upper left side of the instrument panel twice for more than 2 seconds to reset it. The Lynk & Co 03 is a compact 4-door 5-seater sedan with body dimensions of 4639mm in length, 1840mm in width, 1472mm in height, and a wheelbase of 2730mm. It is equipped with a 1.5T turbocharged engine and a 6-speed manual transmission, delivering a maximum power of 115 kW and a maximum torque of 245 Nm. The drive system is front-wheel drive, with a MacPherson independent suspension at the front and a multi-link independent suspension at the rear.
Was this review help?
9
4
Share
More Forum Discussions

Where is the cigarette lighter fuse in a 2015 Audi A6?

15-year Audi A6 cigarette lighter fuse is located in the fuse box under the driver's compartment. Below are some relevant details about the Audi A6: 1. Exterior: Elegance and Sport models to meet different needs, featuring a stable and wide front face, sharp angular engine compartment lines, and elegant lines extending from the front to the rear, combining classic and breakthrough elements. 2. Powertrain: Equipped with a new generation of 2.0L/3.0L turbocharged engines, Audi quatrainultra intelligent all-wheel-drive system, and 12V/48V mild hybrid system, among other diversified powertrain combinations, paired with the Audi driving system, delivering strong performance. 3. Dimensions: The 2021 Audi A6 Elegance model has a body length of 5038mm, a width of 1886mm, and a height of 1475mm, while the Sport model has a body length of 5050mm, with other dimensions being the same.
18
1
Share

How is the 2014 Jiangling Yusheng 2.4 Diesel Version?

Jiangling Yusheng is equipped with a 2.4T diesel engine. The manual transmission model has lower power tuning compared to the automatic version, with relatively low fuel consumption—around 8 liters per 100 kilometers for the manual model. It has a very low failure rate, but issues such as rear axle differential noise, half-shaft oil seal leaks, and body rust have been reported. Below are specific details about the Jiangling Yusheng: 1. Body Dimensions: Yusheng is a Chinese passenger car brand developed by Jiangling Motors Co., Ltd., a joint venture between Ford and Jiangling. Its products are among the few strictly defined joint-venture independent models in the Chinese automotive market. The Yusheng brand focuses on the crossover segment of SUVs and MPVs, committed to delivering high-quality and dynamic crossover vehicles for various consumer groups. The Yusheng brand will play a key role in Jiangling Motors' expansion into the passenger vehicle market. 2. Origin: The Jiangling Yusheng is the first SUV model under Jiangling Motors Co., Ltd., originating from the N350 project launched in 2006. It was completed in the second half of 2010. The powertrain is derived from Ford's next-generation TDCI engine. With the support of Ford's century-long automotive expertise, a new production platform, a global parts procurement system, and an advanced quality control system, Yusheng is ensured of high-quality standards.
4
0
Share

Why does the tire pressure monitor show 1.6bar and keep beeping?

If a CRV suddenly prompts to check tire pressure, it means the tire pressure data of the vehicle is insufficient. It is necessary to inspect the tires to determine the causes of the low pressure and then perform repairs to resolve the issue. Only then can the vehicle be used normally; otherwise, it may affect driving safety. Hazards of overinflated tires: Reduced tire friction and adhesion, affecting braking performance; Causes steering wheel vibration and deviation, reducing driving comfort; Accelerates localized wear of the central tread pattern, shortening tire lifespan; Increases vehicle body vibration, indirectly affecting the lifespan of other components; Excessive stretching deformation of tire cords, reducing tire elasticity and increasing the load on the vehicle during driving; Decreased puncture resistance. When encountering sharp objects like nails or glass on the road, they can easily penetrate the tire, causing internal cracks or blowouts. Hazards of underinflated tires: Increases friction coefficient with the road surface, leading to higher fuel consumption; Causes heavy steering and deviation, compromising driving safety; Increases movement of tire parts, leading to abnormal heat due to excessive rolling; Reduces the functionality of cords and rubber, causing delamination or cord breakage, and excessive friction with the rim, resulting in bead damage and abnormal wear; Multiplies friction between the tire and the ground, sharply raising tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may lead to blowouts; Increases tire deformation, leading to sidewall cracks and excessive heat from flexing, accelerating rubber aging, cord fatigue, and breakage, while also increasing the tire's contact area and accelerating shoulder wear.
5
2
Share

What is the normal tire pressure for a three-wheeled motorcycle?

The normal tire pressure for a three-wheeled motorcycle is 200~225 kPa for the front wheel and 250~280 kPa for the rear wheel. Tire pressure refers to the air pressure inside the tire, and the level of tire pressure plays a crucial role in the performance and power of the vehicle. Measuring tire pressure requires a specialized pressure gauge. It is worth noting that the readings on the pressure gauge can be affected by temperature to some extent. Therefore, in summer, it is common to slightly reduce the tire pressure to prevent blowouts, while in winter, the pressure may be slightly increased. As long as the value remains between 2.2 and 2.5 bar, it is acceptable. The recommended tire pressure should be based on the manufacturer's specifications, which can be found in the vehicle's user manual, on the label next to the driver's door, in the drawer near the driver's seat, or on the fuel tank cap. The manufacturer's recommended tire pressure is also known as the cold tire pressure. The measurement is defined as: at least three hours after parking or if the tire has not been driven more than 2 kilometers. If you can only measure the tire pressure when the tire is hot, subtract approximately 0.3 bar (=4 psi) from the measured value to obtain the cold inflation pressure.
3
4
Share

In winter rainy days, should the defogging use internal or external air circulation?

In winter, when using warm air for defogging, you can first adjust the air circulation mode to external circulation to reduce the temperature difference between the inside and outside of the car. After waiting for a few minutes, switch to internal circulation mode. Using anti-fog spray: When using defogging spray, car owners only need to spray it evenly on the glass surface and then wipe it clean with a dry towel. After wiping, a protective film will remain on the glass surface, altering the surface tension of water molecules and causing fog droplets to coalesce into larger water droplets, thus not obstructing the view. This method is also applicable to other car glass surfaces, especially the exterior rearview mirrors. Homemade defogging spray with dish soap: Mix dish soap with water in a 1:6 ratio, put it in a bottle, and spray and wipe it before traveling. The effect is comparable to commercially available defogging sprays, though the durability is slightly inferior.
7
3
Share

Where to Buy Used Rims?

Cars' used rims can be purchased at professional auto repair centers or specialized modification shops, or searched for on used car trading platforms. When purchasing used rims, it's important to ensure the model matches. Below is a related introduction: Rim Introduction: The rim is the metal component inside the tire that supports the tire and is mounted on the axle, also known as the wheel. There are many types of wheels based on diameter, width, and manufacturing materials, with ordinary car wheels considering appearance less. Enamel Treatment: The heat dissipation performance of the wheel is a primary consideration for ordinary car tires, mostly using enamel treatment. Spraying first and then electric baking is cost-effective, and the wheel's color can last a long time. Electroplated wheels can be divided into types like electroplated silver, water silver, and pure electroplating, with pure electroplating maintaining color for a long time, used by most high-end car models.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.