How to Replace the Roof SOS Battery in a BMW?

1 Answers
KayleeAnn
07/30/25 12:07am
First, hoist the battery pack and remove the upper cover of the battery box. Then, after removing the high-voltage battery cover, disconnect the high-voltage connection wires and remove the high-voltage interface output contactor. Next, dismantle the module fixing bracket and extract the module. Finally, remove the foam spacers at both ends of the module.
Was this review help?
12
2
Share
More Forum Discussions

Why Does a Car Stall When Wading Through Water?

When the water depth exceeds the exhaust pipe, the increased exhaust resistance makes it easier for the engine to stall if the throttle is too small and the engine speed is insufficient to counteract the exhaust resistance. Below are relevant details: 1. Impact: Problems arise when water reaches above the tire level. The biggest concern when wading through water is the potential damage to the engine and electrical systems. Water entering the engine's air intake directly affects the engine, and the electrical system is highly sensitive to water. Therefore, water levels must not exceed the tire height to prevent water from entering the cabin or the engine. 2. Precautions: If the vehicle stalls while wading, never attempt to restart it immediately. Forcing a restart can cause the engine to ingest more water, leading to severe engine damage.
10
0
Share

What is the reason for the water temperature warning light to come on?

Water temperature warning light comes on due to: 1. Insufficient coolant in the vehicle; 2. Engine overheating issue. When the water temperature warning light activates, park the vehicle in a safe location and check if the coolant level is low. If it is insufficient, replenish it immediately while checking for any leakage problems. If leakage is detected, prompt repair is necessary. If the coolant level is adequate, the issue likely stems from engine overheating. In this case, contact professional maintenance personnel immediately for inspection to determine the cause of engine overheating and perform necessary repairs. Under no circumstances should you continue driving to prevent engine damage caused by excessive temperature.
15
2
Share

What is the working principle of the ABS pump?

The working principle of the ABS pump is that when a large current is applied to the solenoid valve, the plunger moves to the upper end, the passage between the master cylinder and the wheel cylinder is cut off, and the wheel cylinder is connected to the hydraulic oil tank. The brake fluid in the wheel cylinder flows into the hydraulic oil tank, reducing the braking pressure. At the same time, the drive motor starts, driving the hydraulic pump to work, pressurizing the brake fluid that flows back to the hydraulic oil tank and delivering it to the master cylinder, preparing for the next braking cycle. The ABS pump is translated into Chinese as "Anti-lock Braking System" and, together with airbags and seat belts, is known as one of the three major inventions in automotive safety history. It is a vehicle safety control system with advantages such as anti-skid and anti-lock functions.
8
1
Share

What does the National IV standard mean?

National IV standard refers to the fourth-phase national motor vehicle emission standard in China. The methods to check a vehicle's emission standard are: 1. Check the motor vehicle conformity certificate. Vehicles come with a conformity certificate upon leaving the factory, which clearly states the emission standard; 2. Refer to the vehicle's packing list, where the emission standard can be found in the vehicle information section; 3. Examine the conformity of production certificate, which includes exhaust emissions and indicates the corresponding emission standard; 4. Query on the Motor Vehicle Environmental Protection Website by entering the vehicle's VIN code and the last 6 digits of the engine number in the public query platform located at the bottom of the homepage; 5. Inspect the vehicle's environmental protection label. The back of the environmental protection label on the vehicle's front windshield clearly indicates the emission standard.
4
5
Share

What are the reasons for the buzzing noise of the power steering pump?

Direction assistance pump buzzing reasons are: 1. The sound of the pressure limiting valve during operation, which is normal; 2. The filter screen is blocked, causing the pump to make noise. The oil pot with a filter screen will become clogged over time and needs to be cleaned; 3. There is a problem with the power steering oil pump, such as air intake in the power steering oil pump, leakage in the high-pressure oil pipe, or issues with the oil pot; 4. Lack of power steering fluid, simply add power steering fluid. The car power steering pump is very important for the driver to control the correct driving direction. If there is a problem with the power steering system, it will affect the driving direction and thus the entire driving safety. Car power steering pumps mainly use hydraulic power assistance, electric power assistance, steering electric power assistance, mechanical hydraulic power assistance, and electronic hydraulic power assistance.
6
4
Share

How to Use the Crawl Mode in Land Cruiser?

Land Cruiser's crawl mode usage method: Park and shift into P gear, then shift into N gear, activate the low-speed four-wheel drive function, engage the central differential lock, and finally shift into D gear and press the auxiliary button. Land Cruiser is a mid-size SUV under Toyota, featuring a retro exterior design, powerful off-road capabilities, and excellent stability. The Land Cruiser is equipped with a 4.0-liter V6 naturally aspirated engine, delivering 272 horsepower and a maximum torque of 380 Nm. It can output maximum power at 5,600 rpm and maximum torque at 4,400 rpm. In terms of body dimensions, the vehicle measures 5,095 mm in length, 1,975 mm in width, and 1,930 mm in height, with a wheelbase of 2,850 mm.
18
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.