How to Replace the Key Battery for the New Mercedes-Benz CLS260?

3 Answers
JakeMarie
07/29/25 6:17pm
The method for replacing the key battery of the new Mercedes-Benz CLS260 is as follows: 1. Press the button on the back of the key, push the back cover forward to open the key, and the battery is located in the slot beside it; 2. Pry open this slot to remove the old battery and replace it with a new one; 3. Next, reattach the back cover of the key. Once the back cover is securely installed, the battery replacement is complete. Symptoms of a low battery are as follows: 1. The lifespan of a Mercedes key battery is generally two years, while the original factory battery can last up to six years. When the key battery is low, the Mercedes vehicle will display two indicators: one is that pressing the ignition switch will prompt a message on the dashboard to replace the key battery. 2. Press the lock or unlock button on the key. If the indicator light on the key dims or does not light up, it indicates that the key battery needs to be replaced.
Was this review help?
19
2
Share
MadelineFitz
08/14/25 10:53am
Just helped a friend replace the battery in their CLS260 key fob a couple of days ago, and it's actually quite simple. There's a small notch on the back of the key—just insert a coin or a small flathead screwdriver and gently pry to open the casing. The battery is a CR2025 coin cell, so make sure not to get the wrong type. When removing the old battery, pay attention to the polarity, and install the new one in the same orientation. You'll hear a click when closing the cover, indicating it's properly secured. After replacement, remember to test the lock/unlock functions. If you notice the remote range getting shorter, it's time to replace the battery—don't wait until it's completely dead and causes inconvenience. When buying batteries online, opt for reputable brands like Panasonic. If purchasing from a supermarket, check the production date to avoid old stock. The key casing is plastic, so avoid using excessive force when prying to prevent scratches and keep it looking good.
Was this review help?
4
1
Share
Expand All
DeBlakely
10/14/25 5:16am
I'm quite familiar with replacing Mercedes key batteries. The CLS260's key design is quite reasonable. First, locate the small notch on the back of the key - you can pry it open using a small steel ruler or thin card. The battery inside is CR2025 specification, smaller than a fingernail. When installing, make sure the silver side faces upward; it won't work if installed backwards. The whole process takes just three minutes, and even women can do it without difficulty. Here's a little tip: if the remote doesn't work after battery replacement, try pressing and holding both the lock and unlock buttons simultaneously for ten seconds to reset the system. When buying batteries at the supermarket, be careful not to pick CR2032 by mistake - although similar in size, they differ in thickness. It's recommended to perform the replacement in a dry environment as moisture can oxidize the battery contacts. Remember to recycle the old battery properly; don't discard it carelessly and pollute the environment.
Was this review help?
3
1
Share
Expand All
More Forum Discussions

What is the adjustment method for a hydraulic clutch?

Hydraulic clutches cannot be adjusted for height. A high hydraulic clutch position indicates severe wear of the clutch three-piece set, resulting in excessive free travel of the clutch. This requires replacing the clutch disc, driven plate, and release bearing. Solutions for a heavy hydraulic clutch include: 1. The clutch operating mechanism's mechanical part is stuck: The clutch master cylinder lacks hydraulic oil or has a leak; replace the clutch or add clutch fluid. 2. The clutch slave cylinder is rusted: The clutch booster cylinder's air passage is blocked or the cylinder is leaking air; replace the clutch slave cylinder. 3. The clutch release fork is broken or bent: The release bearing or bearing seat has fallen off. Replace the clutch release bearing.
4
0
Share

What lights should be used when passing through an intersection at night?

When passing through a signalized intersection at night, low beam headlights should be used. Here are the specific details: 1. Passing through intersections at night. If passing through an intersection without traffic signals, it is necessary to alternate between high and low beam headlights when approaching the intersection to alert vehicles and pedestrians in the perpendicular direction. Additionally, speed should be reduced when nearing the intersection to prevent sudden incidents, allowing sufficient time to respond. 2. Use of lights at night. When driving on well-lit roads, low beam headlights should be used, and they should also be used when following another vehicle to make it easier for the preceding vehicle to observe the situation behind through the rearview mirror. If meeting an oncoming vehicle at a distance of 150 meters, high beams should be switched to low beams. Furthermore, when driving at night and encountering slopes, arched bridges, crosswalks, sharp curves, or when overtaking another vehicle, it is necessary to alternate between high and low beam headlights.
5
1
Share

Reasons for the Vehicle Not Accelerating When the Throttle is Increased

About the reasons for the vehicle not accelerating when the throttle is increased are introduced as follows: 1. Insufficient engine torque. (1) Engine misfire: The ignition coil of a certain cylinder is damaged, causing the engine to change from 4 cylinders to 3 cylinders. At this time, the fuel efficiency of the engine is very low, and the output torque value of the engine is small. (2) Problem with the engine fuel pump: The engine fuel pump is damaged, leading to insufficient fuel supply from the engine, resulting in weak acceleration. (3) Problem with valve timing: To improve the fuel efficiency of the engine, modern engines use a CVVD valve timing system. However, if the CVVD hydraulic control system is damaged or the sealing ring leaks oil, it will also reduce the engine's fuel efficiency, leading to poor engine output torque. 2. Damage to the vehicle's transmission. The vehicle's transmission experiences slipping and wear, and the power output from the engine cannot be transmitted to the vehicle's tires, causing the vehicle speed to not increase. If the clutch friction plate is excessively worn, causing the clutch temperature to rise very easily, it will also make the input and output ends of the clutch very prone to slipping. The engine's power cannot be fully transmitted to the transmission, resulting in the vehicle's inability to accelerate.
7
5
Share

Does the throttle control air intake or fuel intake?

Throttle controls air intake, here are the details: 1. The throttle controls the air intake through the throttle valve. After the air intake is determined, the engine computer will decide how much fuel to inject based on this air intake. The throttle valve helps achieve the optimal air-fuel ratio, ensuring complete combustion of gasoline and maximizing energy utilization for power generation. 2. Introduction to gasoline engines. Gasoline engines rely on spark plugs to ignite the fuel. The air and gasoline form a mixture that enters the cylinder. When the piston approaches the top dead center, the spark plug ignites the mixture, and the flame spreads outward from the spark plug until complete combustion occurs. This process requires a certain amount of time.
6
2
Share

What is the fuel consumption of the Fengjun 5?

Fengjun 5 fuel consumption is 9.9L/100KM, here is the relevant information: 1. Vehicle positioning: Fengjun 5 is a pickup truck under Great Wall, with dimensions of 5095mm in length, 1800mm in width, and 1740mm in height, a wheelbase of 3050mm, and a front-engine, rear-wheel-drive layout. 2. Power: It uses a 2.4L naturally aspirated engine with a maximum torque of 230 N·m, paired with a 5-speed manual transmission. 3. Suspension type: The front suspension is double-wishbone independent suspension, the rear suspension is leaf spring non-independent suspension, and the tire specification is 235/70R16.
8
2
Share

How Long Does the BYD Qin Battery Last?

BYD Qin's battery lifespan ranges between 5 to 8 years. There are primarily two types of batteries for the BYD Qin models available in the market: those produced after 2018 use ternary lithium batteries, while models before 2018 are equipped with lithium iron phosphate batteries. BYD is a Chinese automotive brand established in 1995, specializing in the production of commercial and family sedans, as well as batteries. Starting with a team of just over 20 people, BYD grew to become the world's second-largest rechargeable battery manufacturer by 2003, the same year it ventured into automobile manufacturing. In the passenger vehicle market, BYD operates in both the traditional fuel-powered and new energy vehicle sectors. Since launching the world's first mass-produced plug-in dual-mode electric vehicle in 2008, BYD has introduced a series of new energy models, including the e6, Qin, Tang, Song, Yuan, Han, and Dolphin. The BYD Qin is a high-performance sedan independently developed by BYD Co., Ltd., featuring the second-generation DM technology that allows switching between pure electric and hybrid electric modes. Its body dimensions are 4740mm in length, 1770mm in width, and 1480mm in height.
17
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.