How to Replace the Complete Car Lock for BYD L3?

2 Answers
MacLily
07/24/25 1:23am
Here is the method for replacing the complete car lock for BYD L3: 1. Clear the original key code. 2. Register the new key code. 3. Perform remote matching to complete the replacement. Below are daily precautions for car key usage: 1. Every time you exit the car, even if it's just for a few minutes, turn off the engine, remove the key, and lock the car to prevent giving thieves an opportunity. 2. Car keys should be kept waterproof, protected from severe vibrations, and kept away from magnetic interference. If the key is damaged, it also needs to be replaced. 3. Keep the spare key and the main key separate. Do not lock the spare key inside the car, especially for vehicles with one-button start or engine immobilizers, as the spare key can fully start the engine. 4. If the key is lost and cannot be matched in time, do not leave valuables in the car. Additionally, consult your insurance company about the details of compensation for vehicle theft to ensure you have the necessary evidence in case the vehicle is stolen.
Was this review help?
1
1
Share
HarrisonAnn
08/10/25 9:01pm
I once replaced the entire lock set on my BYD L3, which was quite an interesting experience. First, you need to purchase an original or compatible lock kit, including door locks, trunk lock, and ignition lock. Prepare the necessary tools: Phillips screwdriver, hex key, plastic pry bar, and gloves to prevent scratches. When removing interior panels, gently pry open the clips—don’t force them and damage the plastic. Then locate the screws of the old locks, loosen and remove them, and install the new locks in the correct position. If it’s an electronic central locking system, you’ll need a diagnostic tool to program and match the keys, otherwise the car won’t start. The whole process takes about half a day, and you should test each lock to ensure smooth operation. Remember to disconnect the car battery first to avoid short circuits and wire damage. It’s not too difficult, but beginners should watch online BYD tutorials for details to avoid costly mistakes.
Was this review help?
14
1
Share
Expand All
More Forum Discussions

What Causes Frost on Car Windows in Winter?

The reason for frost forming on car windows in winter is due to the temperature difference between the inside and outside of the vehicle. Because the temperature inside the cabin is higher than outside, the car windows come into contact with the colder external environment, causing the moisture inside the cabin to condense on the inner windshield and form frost. When the moisture in the warm air approaches the cold window, it cools down and condenses into frost on the glass. Frost typically forms in winter or during cold mornings and evenings. Below is more information about frost on car windows in winter: 1. When this happens in winter, opening the windows to reduce the temperature difference between the inside and outside of the car can help melt the frost. 2. Turning on the car's heating mode and directing the air vents toward the frosted areas can also help, though the downside is that it takes longer to remove the frost. The advantage is that raising the temperature inside the car makes it less likely for passengers to feel cold and achieves the goal of defrosting.
9
3
Share

What is the ground clearance of the XRV?

The minimum ground clearance of the Honda XRV is 135/140mm. Below is some relevant information about the Honda XRV: 1. The Dongfeng Honda XR-V is a new SUV model launched by Dongfeng Honda at the Chengdu Auto Show in November 2014. 2. In terms of dimensions, the XR-V measures 4275/1770/1605mm in length, width, and height respectively, with a wheelbase of 2610mm. 3. In terms of power, the new model will be available with either a 1.8L naturally aspirated engine or a 1.5L Earth Dreams engine. The former has a maximum power output of 136Ps. The transmission system is paired with either a 6-speed manual transmission or a CVT transmission.
4
2
Share

Why is the steering still not straight after wheel alignment?

The reasons why the steering is still not straight after wheel alignment are as follows: 1. Unequal tire pressure. Different tire pressures in the four wheels or on both sides can cause the wheels to vary in size, affecting the vehicle's balance, which inevitably leads to pulling. 2. Inconsistent or failed shock absorber damping. If the vehicle's shock absorbers fail or provide inconsistent damping, the suspension may be uneven during driving, causing uneven force distribution on both sides of the vehicle and resulting in pulling. 3. Uneven brake force distribution. If any of the brakes have poor return or incomplete separation, the wheel will continuously be under force during driving, leading to vehicle pulling. 4. Abnormal clearance in the chassis. Excessive wear of the vehicle's chassis components can cause abnormal clearances, which may also result in pulling. 5. Overall frame deformation. If the vehicle's frame is deformed, causing a significant difference in the wheelbase on both sides beyond the maximum allowable range, it will lead to pulling.
17
5
Share

In which year did the Magotan switch to the third-generation EA888?

Magotan made the switch in 2016. Here is the relevant information: Engine: An engine is a machine that converts other forms of energy into mechanical energy, including internal combustion engines (reciprocating piston engines), external combustion engines (Stirling engines, steam engines, etc.), jet engines, electric motors, etc. Comfortable Driving Experience: The 6-speed Tiptronic automatic/manual transmission, which forms a perfect match with the 1.8TSI engine, allows Magotan owners to enjoy the ease of an automatic transmission while also experiencing the driving pleasure of manual shifting. The 6-speed Tiptronic automatic/manual transmission performs exceptionally smoothly during gear shifting and acceleration, complemented by the powerful output of the 1.8TSI engine, making the Magotan 1.8TSI respond swiftly and sensitively during instant acceleration with exceptionally robust power.
10
3
Share

What is the solution for the sunroof rattling in the Volkswagen Sagitar?

The solutions for the sunroof rattling in the Volkswagen Sagitar are: 1. Open the sunroof completely and spray sealant lubricant on the rubber seals; 2. Tighten the sunroof screws; 3. Remove dust with a towel. Precautions for using the sunroof: 1. Check if the sunroof rails are in normal condition; 2. Avoid frequent use of the sunroof; 3. Do not open the sunroof when the car is cold in winter; 4. Check the drainage condition of the sunroof during the rainy season. The body dimensions of the Volkswagen Sagitar are: length 4644mm, width 1778mm, height 1482mm, wheelbase 2651mm, and minimum ground clearance 108mm.
19
1
Share

What is the method to check the condition of an ignition coil?

Check the condition of an ignition coil by: 1. Using the substitution method—replace one ignition coil with a known good one; if the fault disappears, it indicates the original coil is faulty. 2. Measuring the primary and secondary winding resistances with a multimeter; a high resistance reading suggests an open circuit fault in the winding. The steps to replace an ignition coil are: 1. Open the ignition coil cover on top of the engine. 2. Remove the ignition coil fixing screws. 3. Disconnect the ignition coil power plug. 4. Remove the ignition coil. 5. Install the new ignition coil and tighten the screws. 6. Reconnect the power plug and replace the top cover.
9
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.