···
Log in / Register

How to Replace the Cabin Air Filter in Mazda CX-5?

5 Answers
FrankMarie
07/29/25 11:42am

Mazda CX-5's cabin air filter replacement steps are as follows: 1. Open the glove box and lift the plastic hook on the right side of the glove box; 2. Press both sides of the glove box with your hands and pull it outward to remove the glove box housing; 3. After removing the glove box housing, you can see the cabin air filter. At this time, pry the plastic clips on both sides of the cabin air filter outward to remove them; 4. After removing the plastic clips, you can take out the old cabin air filter. Replace it with a new one and reassemble the glove box in the reverse order of disassembly. The entire replacement process is then completed. The Mazda CX-5 is positioned as a compact SUV with a length, width, and height of 4555mm, 1840mm, and 1710mm respectively, and a wheelbase of 2700mm.

Was this review help?
10
2
Share
EmiliaRose
08/13/25 8:15pm

I always find it quite convenient to change the air filter for my Mazda CX-5 myself. Generally, it's located under the glove compartment in front of the passenger seat. You just need to empty the glove box, press the clips on both sides to lower it, and you'll see a black plastic cover. The cover is secured with screws, which can be easily removed with a simple screwdriver. When taking out the old filter, remember the direction of the arrow, and make sure the new filter's arrow points toward the front of the car when putting it back. The whole process takes about 15 minutes and doesn't require expensive tools, saving you the hassle and cost of going to the dealership. Additionally, I usually replace it every 15,000 kilometers or so to prevent odors or allergy-induced sneezing in the car. Fresher air also improves mood, making long drives less tiring.

Was this review help?
5
2
Share
Expand All
AdrianaLynn
10/08/25 6:04am

I've been driving the CX-5 for several years and always pay attention to these maintenance details. When replacing the cabin air filter, the first step is to turn off the engine and wait for it to cool down before proceeding - safety first. The filter is located behind the glove box, just remove that cover directly but be careful not to break the plastic clips. When taking out the old filter, check carefully - the arrow should face downward when installing the new replacement. Keep a spare new filter handy, they cost just a few dozen bucks at supermarkets - don't go for the cheapest option. During routine maintenance, take the opportunity to check it; a dirty filter can easily affect AC airflow. I personally do a quick visual check every month to prevent reduced airflow from a clogged filter - nobody wants to suffer through a stuffy, hot summer drive.

Was this review help?
8
2
Share
Expand All
McGeorge
11/21/25 7:22am

When my family and I go out in this car, our biggest concern is bacteria from the AC affecting our health. Changing the filter is simple: sit on the passenger side, open the glove box, and there's a small door. Unscrew it to remove the old filter. Align the arrow on the new filter with the correct direction, and it's done in two minutes. I recommend buying filters from reputable brands and replacing them every six months or 10,000 kilometers – the air in the car feels much fresher. The kids sneeze less. Also, avoid cluttering the glove box to prevent blocking the filter location. Regular replacements are hassle-free and inexpensive – a practical family tip.

Was this review help?
5
5
Share
Expand All
BellaLynn
01/12/26 2:10am

Young car owners' top DIY choice, I love changing the CX-5's cabin air filter. Short steps: open the glove box, unscrew and remove the cover, take out the old filter and replace it. Don't get the arrow wrong, just point it towards the interior. Prepare a Phillips screwdriver and a filter under 30 bucks to get it done. Plenty of video tutorials online, find one for quicker reference. Don't delay, a dirty filter makes the air smell bad when blown. After replacement, just test if the AC fan speed is normal. Saves time and effort, 20 minutes without a trip to the shop.

Was this review help?
8
2
Share
Expand All
More Forum Discussions

What Position Is One Full Turn of the Steering Wheel?

Steering wheel rotation of one full turn means turning 360 degrees. Steering wheel: A wheel-shaped device in cars, ships, airplanes, etc., used to control the direction of travel. Its function is to convert the force applied by the driver to the edge of the steering wheel into torque and then transmit it to the steering shaft. In an S-curve, you should steer towards the wider side. Below is some information about S-curves: 1. Precautions: Use the rearview mirror to check behind you; if the rear of the car is wider on one side, steer towards that side. Avoid reversing too quickly and make corrections as needed to prevent collisions. Generally, avoid turning the wheel fully to prevent scraping the front corners of the car. It's best to have someone observe and remind you from outside the car. 2. Principle: Steering follows the rule of 'turn as much as you need to correct, turn quickly if you need to correct quickly, turn slowly if you need to correct slowly.' For example, if the left rear of the car is wider, turn the wheel 90 degrees to the left. When you are about to achieve the desired effect, turn the wheel 90 degrees back to the right. The speed of turning follows the same principle.
4
5
Share

Is It Necessary to Pass Through Neutral Gear When Shifting?

When driving, it is not necessary to pass through neutral gear every time you shift. For manual transmission vehicles, in the past, you had to press the clutch to shift from first gear to neutral, release the clutch, then press the clutch again to shift from neutral to second gear. This practice was relevant for transmissions without synchronizers. Relevant information about the clutch is as follows: 1. Introduction: The clutch is located inside the flywheel housing between the engine and the transmission. The clutch assembly is fixed to the rear plane of the flywheel with screws, and the output shaft of the clutch is the input shaft of the transmission. 2. Friction Clutch: The friction clutch is the most widely used and historically oldest type of clutch. It basically consists of four parts: the driving part, the driven part, the pressing mechanism, and the operating mechanism.
13
3
Share

What is the actual fuel consumption of the Renault Koleos?

The official combined fuel consumption of the Renault Koleos is 6.4-7.6L/100km. Here are the detailed specifications of the Koleos: 1. Vehicle Positioning: The Koleos is a compact SUV produced by Dongfeng Renault, with dimensions of 4672mm in length, 1843mm in width, and 1678mm in height, and a wheelbase of 2705mm. 2. Powertrain: The Koleos is equipped with either a 2.0L or 2.5L naturally aspirated engine, paired with a CVT transmission that simulates 7 gears. 3. Safety Features: Except for the base model, side airbags, side curtain airbags, electronic stability control, rain-sensing wipers, heated and power-folding mirrors are standard. The four-wheel-drive version comes standard with hill start assist and hill descent control.
8
0
Share

Why does the Tiguan L's battery only last for a little over 2 years?

It is mainly due to insufficient daily maintenance by the owner. Under normal circumstances, it can last for three years. Below are some precautions for car battery maintenance: 1. Avoid leaving the vehicle parked for extended periods: The car battery will self-discharge over time when left idle. It is best to drive the vehicle at least once a week, with a trip duration of at least 20 minutes, to allow the battery to recharge while driving. 2. Close windows before turning off the engine: The power windows and sunroof rely on the battery for operation. Therefore, it is advisable to close all windows before turning off the engine, rather than after. Avoid using the long-press lock button method to close windows after leaving the vehicle. 3. Keep the battery clean and tidy: Regular inspections are an effective way to extend the battery's lifespan. Use a professional battery terminal brush or an old toothbrush to clean dust and corrosion from the positive and negative terminals. Apply a layer of protective coating, such as petroleum jelly or grease, to the contact surfaces to form a protective film.
5
3
Share

Do You Need to Press the Brake for One-Button Start?

One-button start requires pressing the brake to ignite and start the engine. When starting the engine, you must press the brake pedal. If the brake pedal is not pressed, the engine will not start. This is a safety design in cars to prevent accidental activation of the switch, which could cause the vehicle to suddenly move forward. When the vehicle is turned off, pressing and holding the one-button start for 3 seconds without stepping on the brake will only power the electrical system without starting the engine. For some models, you need to press the ignition switch twice. Cars with one-button start are usually automatic. During one-button start, the engine goes through a high-speed starting process. If the driver does not press the brake, it may cause the car to lurch forward unexpectedly, potentially leading to a rear-end collision. Cars equipped with a one-button start system allow the driver to start the engine simply by carrying the key into the vehicle. There is no need to insert or turn the key—just press the brake pedal and the start button to ignite the engine. The one-button start system was originally used in racing cars, enabling drivers to quickly start the engine and get into the race. Later, this system was adopted for civilian vehicles. In addition to pressing the brake, when starting a one-button start car, it is also important to ensure the gear is in the P (Park) position. If the gear is not in P, the car will not start. If pressing the one-button start does not elicit any response, it could be due to a dead key battery or interference from nearby sources. In such cases, bringing the smart key close to the one-button start button while pressing the brake and the start button may allow the car to start.
8
3
Share

What kind of engine oil is suitable for the Land Cruiser 4000?

Land Cruiser 4000 is suitable for moderately priced engine oils such as Mobil, Shell, Castrol, and Total. Below are the relevant details about the Land Cruiser 4000: 1. Exterior: The Land Cruiser 4000 has dimensions of 4950×1970×1880mm (length/width/height) and a wheelbase of 2850mm. 2. Performance: Maximum torque: 376NM/3800RPM; Transmission type: 6-speed automatic transmission; Fuel tank capacity: 138L; Cylinder arrangement: V; Combined fuel consumption: 10.99L/100KM; Drivetrain: Full-time four-wheel drive.
12
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.