···
Log in / Register

How to Replace the Cabin Air Filter in Changan CS35?

4 Answers
DelilahLynn
07/23/25 6:38pm
Changan CS35 cabin air filter replacement steps: 1. Locate the fixing buckle on the right side of the glove compartment and pull it outward firmly. 2. After removing the glove compartment, you will see the cabin air filter cover. Press the fixing buckles on both sides of the cover firmly to remove it. 3. Pull out the old cabin air filter outward, then insert the new one and reassemble in reverse order of disassembly. The function of the car cabin air filter is to filter the air entering the cabin from outside, improving air cleanliness, providing a good air environment for passengers, and protecting the health of occupants.
Was this review help?
9
1
Share
StTheo
08/10/25 2:16pm
I always change the air conditioning filter for my Changan CS35 by myself, which saves a lot of money. First, buy a CS35-specific air conditioning filter online, and remember to choose one with activated carbon for better filtration. When replacing it, first empty the glove box, press the plastic clips on both sides of the glove box inward and push them while pulling downward, and the entire glove box will drop down. Then you will see the filter slot cover, pinch the clips at both ends to remove the cover, and pull out the old filter, paying attention to the arrow direction. Insert the new filter with the arrow pointing toward the front of the car, making sure it is fully in place to avoid air leakage. Finally, snap the cover back on and push the glove box back into place. The whole process takes about ten minutes, and beginners are advised to turn off the engine and disconnect the power before operating.
Was this review help?
2
4
Share
Expand All
VeraFitz
09/22/25 9:05am
Every time I help friends replace the CS35's cabin air filter, I remind them of a few key points: The glove compartment clips are particularly fragile, so avoid using excessive force when pressing them. The arrow on the filter must face the front of the car; installing it backward will reduce airflow. For models with a damper rod in the glove box, support it during removal to prevent breakage. I usually start the car after replacing the filter and run the AC at maximum fan speed for two minutes to ensure the filter fits snugly. It's recommended to replace the filter every six months or 5,000 kilometers, especially in northern areas with lots of willow catkins or humid southern regions. Buying the filter yourself costs only 20-30 yuan, much cheaper than at a 4S shop.
Was this review help?
10
5
Share
Expand All
VonJohn
11/06/25 3:25am
When I first learned to replace the cabin air filter, it seemed quite troublesome. But later I discovered the thoughtful design of the Changan CS35. No tools needed! Just open the glove compartment on the passenger side, press the clips on both sides inward simultaneously with both hands, and the entire compartment lowers down. The rectangular cover inside can be opened with a simple pull, and removing the old filter is as easy as pulling tissues from a box. The key point is to align the arrow on the new filter with the direction of the car's front, then push it into place. The whole process takes just five minutes, and I succeeded on my first attempt. Remember to buy the CS35-specific model and never operate while the engine is running. Check the filter monthly for leaves or debris, especially after driving on dirt roads.
Was this review help?
18
1
Share
Expand All
More Forum Discussions

What is the first maintenance mileage for Honda 190TR?

Honda 190TR's first maintenance is at 1000 kilometers. First maintenance includes: Changing engine oil and oil filter, checking all vehicle lights, fluid levels, electrical system functions, tire inspection and pressure adjustment, inspecting chassis components for normal condition, checking for oil leaks in engine and transmission, and ensuring proper operation. A professional diagnostic device will be used for a computer scan of the entire vehicle, and the maintenance reminder will be reset. First maintenance mileage: Different brand models may have varying requirements, but most require the first maintenance between 3000 to 5000 kilometers. Some brand models may require the first maintenance at around 8000 to 10000 kilometers.
16
0
Share

What are the differences between YueDong 75 and 70?

YueDong 75 and 70 differ in clarity, heat insulation effect, and price. Clarity: YueDong 70 and 75 have 71% and 75% visible light transmittance respectively. YueDong 75 has the highest visible light transmittance, meaning it provides the clearest vision. Therefore, in terms of clarity, YueDong 75 is better than 70. Heat insulation effect: YueDong 70 has a total solar energy rejection rate of 45%, higher than YueDong 75's 33%. In terms of heat insulation performance, YueDong 70 is better than 75. Of course, the price of YueDong 70 is also higher than that of 75. Price advantage: It must be said that YueDong 75 has a significant price advantage. The full car price of YueDong 75 is around 1100 yuan, which is much cheaper than YueDong 70's 1880 yuan. Therefore, in terms of price, YueDong 75 has an advantage over YueDong 70.
7
1
Share

Why does Volkswagen's parking brake and ABS fail?

Reasons for Volkswagen parking brake and ABS failure: Wheel speed sensor, ABS wiring, ABS pressure regulating solenoid valve, ABS computer failure; insufficient brake fluid; dirty ABS sensor. The method to eliminate the ABS warning light is to unplug the ABS power supply in the engine compartment. Function of ABS: Maximize the effectiveness of the brakes, shorten braking time and distance. Effectively prevent vehicle skidding and fishtailing during emergency braking, ensuring good driving stability. Allow steering during emergency braking, providing good steering maneuverability. Avoid severe friction between tires and the ground, reducing tire wear. Working principle of ABS: During braking, ABS quickly determines the wheel lock-up state based on speed signals from each wheel speed sensor, closes the normally open input solenoid valve on the wheel that is starting to lock, keeping the braking force unchanged. If the wheel continues to lock, the normally closed output solenoid valve is opened, causing the brake pressure on that wheel to rapidly decrease due to the direct connection to the brake fluid reservoir, preventing complete wheel lock-up from excessive braking force. This keeps the braking state always at the optimal point (slip rate S of 20%), achieving the best braking effect and the highest driving safety.
19
2
Share

Why is the daytime running light of Baojun 560 not working?

The reasons why the daytime running light of Baojun 560 is not working include a blown fuse or a burnt-out bulb. Check if the fuse is blown: Use a screwdriver to connect the hot wire of the dimmer switch to the high beam and low beam terminals respectively, and observe the following scenarios: If all lights turn on, it indicates a fault in the dimmer switch. If the high beam works but the low beam does not when connected, the fault lies between the dimmer switch and the headlight or the low beam. If the high beam of the headlight does not work, check if the high beam indicator light is on. If it is, the fault is between the terminal block and the headlight; if not, the fault is between the terminal block and the dimmer switch. If only one headlight works while the other does not, it may be due to a burnt-out filament, an open circuit, or poor grounding (dim headlight). Check if the bulb is burnt out: The voltage regulator may be faulty, causing excessively high voltage. Poor contact in the battery cables can lead to excessively high no-load voltage from the generator. There may be a short circuit between the generator armature and the field coil.
3
4
Share

What transmission does the Mercedes-Benz E-Class use?

The Mercedes-Benz E-Class uses a 9-speed automatic transmission with manual mode. Introduction to transmissions: A transmission consists of a gear transmission mechanism and a control mechanism. It has evolved from manual transmissions in the past to continuously variable transmissions (CVT) today, enabling the engine to achieve lower fuel consumption while operating at higher power outputs. The transmission can alter the vehicle's rotational speed and expand the driving wheel's torque and rotation speed. Classification of transmissions: Automatic transmissions have become mainstream internationally, primarily including AT, AMT, CVT, and DCT types. Early AT transmission systems mainly used 4-speed configurations. AT transmissions achieve gear shifting through electronically controlled automatic operating systems. CVT is a true continuously variable transmission with fewer components and a compact size. DCT features dual clutches.
10
2
Share

Why does the Volkswagen CC make noise when accelerating?

There are several reasons why a Volkswagen CC may produce noise when accelerating, including loose fasteners, deformation or damage of certain components, improper assembly adjustment or repair, and excessive clearance between parts. Loose fasteners: Vibration during engine operation can cause certain parts to become loose, resulting in impact sounds. For example, loose flywheel mounting bolts or connecting rod bolts can cause abnormal noises. Deformation or damage of certain components: Abnormal noises can be caused by deformation or damage of certain parts. For example, a bent connecting rod can lead to piston slap, and broken valve springs or a fractured crankshaft can also cause unusual sounds. Improper assembly adjustment or repair: Incorrect assembly adjustment or repair can lead to improper clearance between components. For instance, overly tight piston pin assembly or improperly adjusted valve clearance can result in abnormal noises. Excessive clearance between parts: Clearance between parts is an important indicator of automotive assembly quality. When lubrication, temperature, load, and speed are constant, abnormal noises become more pronounced as the clearance increases. Natural wear of certain moving engine components can cause the clearance to exceed the acceptable range, leading to noises such as piston slap against the cylinder wall or impact sounds between connecting rod bearings and journal.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.