How to Replace the Battery in a Magotan?
4 Answers
Method for replacing the battery in a Magotan: Prepare tweezers and a new battery. Use tweezers or a blade to pry open the gap on the side, remove the old battery, and insert the new one. Be careful when prying to avoid scratching the remote control casing. Below is a detailed introduction to the battery replacement method for the Magotan: 1. Pull the front hood release lever located below the driver's side, then open the hood to locate the battery. 2. Remove the protective cover of the battery terminal and the nut of the fixing bracket. 3. First disconnect the negative terminal, then remove the positive terminal. This is to prevent short circuits, as the negative terminal is connected to the vehicle body. 4. After removing the surrounding fixtures and the positive and negative cables, the battery can be taken out for replacement. (Note: The electrolyte from the old battery can easily leak, so do not tilt it more than 40° when removing it.)
As a frequent DIY car owner, I’d like to share the detailed steps for replacing a Magotan battery. First, park the car on a level surface, turn off the engine, remove the key, and engage the handbrake to ensure safety. Open the engine hood and locate the battery box, usually on the right side of the engine. Wear insulated gloves and safety goggles to prevent electric shock or acid splashes. Step 1: Use a wrench to loosen the negative terminal connection (marked in black) and completely remove the cable end; then loosen the positive terminal (marked in red) and remove it. After disconnecting both, unfasten the battery bracket bolts and carefully remove the old battery to avoid tilting and leakage. Choose a new battery matching the original specifications, such as a 60Ah capacity, and place it back in position, securing the bracket. When reconnecting the cables, follow the reverse order: first attach the positive terminal and tighten the bolt, then connect the negative terminal. After completion, start the engine to test—if the dashboard lights up and the engine starts smoothly, it’s done correctly. You may need to reset the radio or clock settings. Dispose of the old battery at an automotive recycling point. The entire process can be completed within 20 minutes, and it’s recommended to consult the owner’s manual for more precise instructions before starting.
When I first learned car repair, I changed the battery of a Magotan, which is quite beginner-friendly. Turn off the engine, remove the key, and park the car in a safe place. After opening the hood, locate the square box at the front—that's the battery. Remember to wear gloves to protect your hands and avoid direct contact with metal. The battery has two terminals: the black negative and the red positive. The first step is to use a wrench to loosen the bolt on the black cable and disconnect it to cut off the power. Then, disconnect the red cable. After removing the old battery's securing mechanism, gently lift it out. Place the new battery of the same model in position and secure it. The order changes when reconnecting the wires: first connect the red wire and tighten it, then connect the black wire. Finally, start the car to see if it works on the first try. If you accidentally reverse the order, sparks may occur—be careful. If it doesn’t work the first time, check if the bolts are tight. After replacement, the radio might reset, but you can reconfigure it later. It’s recommended to practice a few more times to get used to it.
I usually change the battery myself to save money and it's quick. The original battery for the Magotan is a bit expensive, but doing it yourself can save you a hundred yuan in labor costs. When choosing a new battery, go for a good brand like Fengfan, which costs between 300-500 yuan. Steps: Turn off the car and remove the key, wear gloves and locate the battery. All you need is a simple wrench. Make sure to disconnect the wires in order: first the negative (black) wire, then the positive (red) wire. Remove the old battery, replace it with the new one, and secure it properly. When reconnecting, reverse the order: first the red wire, then the black wire, and tighten the bolts. Test the startup; if it's slow or fails, the connections might be loose—double-check them. Don’t waste the old battery; you can give it to a recycling station for a small refund. The whole process takes about 15 minutes once you’re familiar with it, and it’s very cost-effective. Just make sure the new battery matches the original specifications to avoid instability, and always check that the mounting bracket is secure.
