How to Replace the Battery in a Hyundai Elantra Key?

2 Answers
Edmund
07/28/25 7:54pm
The battery type for the Elantra: CR2032. Follow these steps to replace the battery: 1. Insert a thin tool into the slot and gently pry open the remote cover. 2. Remove the old battery and install the new one, ensuring correct battery placement. 3. Reattach the remote key cover. Additional details: 1. If you suspect the remote key is damaged or not functioning properly, consult an authorized Hyundai dealer. Improper disposal of batteries can harm the environment and human health; dispose of them according to local laws and regulations. 2. Each vehicle can register up to 2 smart keys. If a smart key is lost, immediately take the vehicle and remaining keys to an authorized Hyundai dealer. Towing may be required if necessary. 3. If a smart key is placed too close to a mobile phone, the phone's normal operation signals may interfere with the key's signals, especially during calls, texting, or sending/receiving emails. Avoid storing the smart key and mobile phone in the same pocket or jacket; maintain sufficient distance between the two devices.
Was this review help?
9
5
Share
DePeyton
08/12/25 12:44am
I've been driving a Hyundai Elantra for several years, and changing the key fob battery is quite simple. First, use a small flathead screwdriver to remove the tiny screw on the back of the key. If there's no screw, just pry open the casing with your fingernail or a plastic pry tool—avoid using metal to prevent scratches. Once opened, you'll see the coin cell battery inside, usually a CR2032 model. Note the positive/negative orientation before removing the old battery. New batteries can be bought at supermarkets or stationery stores for about one yuan. When installing the new battery, make sure the positive side faces upward, gently press it in, then reassemble the casing and tighten the screw. After assembly, test the buttons to ensure they work. If it still doesn't function, there might be contact issues or the key might be damaged. To extend battery life, avoid dropping the key or exposing it to high temperatures—typically, the battery lasts one to two years before needing replacement.
Was this review help?
20
5
Share
Expand All
More Forum Discussions

How to Heat the Rearview Mirror on the Envision?

The method to heat the rearview mirror on the Envision: The heating button for the rearview mirror is the same as the rear window defogging button. Press it once to turn it on or off. The principle is very simple—an electric heating element is installed inside the mirror lenses on both sides, which heats the rearview mirrors to evaporate moisture on the surface. The Envision is a mid-size SUV produced by SAIC-GM Buick, with body dimensions of 4686mm in length, 1839mm in width, and 1660mm in height, and a wheelbase of 2750mm. In terms of power, the Envision offers two engine options: a 1.5-liter turbocharged engine and a 2.0-liter turbocharged engine. The 1.5-liter turbocharged engine delivers a maximum horsepower of 169 PS, a maximum power of 124 kW, and a maximum torque of 250 Nm. The 2.0-liter turbocharged engine provides a maximum horsepower of 260 PS, a maximum power of 191 kW, and a maximum torque of 400 Nm.
11
1
Share

What is the first maintenance mileage for the Volkswagen T-Roc?

Volkswagen T-Roc's first maintenance is at 5000 kilometers. First maintenance considerations: The grade of engine oil to be added should follow the oil standard specified in the manual, ensuring that the car engine's compression ratio coefficient matches the gasoline's anti-knock coefficient. Price should not be the determining factor. Using high-quality lubricating oil can effectively protect the engine, reduce wear, and improve the vehicle's economic performance. Generally, for new cars in good condition, the maintenance interval can be appropriately extended. For cars in poor condition or under harsh usage conditions, the maintenance interval should be appropriately shortened. Maintenance cycle for Volkswagen T-Roc: The first maintenance is recommended after driving 5000 kilometers. Subsequent maintenance intervals can be longer, with maintenance every 7500 to 10000 kilometers, or every six months to a year. Each maintenance mainly includes oil change, tire pressure inspection, and air filter replacement. When changing the oil, the oil filter must be replaced together, and when purchasing the oil filter, it is essential to choose genuine products from well-known brands, as the oil filter is a relatively important component. Tires are also crucial rubber components of a car, and it is recommended to replace them every four years.
15
3
Share

How to reset the oil level warning in Volkswagen vehicles?

Volkswagen oil level reset method is as follows: 1. Keep the engine turned off, turn the ignition switch to the ACC position; 2. Within 5 seconds, slowly press the accelerator pedal all the way down and release, repeat three times; 3. Turn off the ignition switch, then start the vehicle. If the oil light is on but there is no oil shortage, it may be caused by other reasons: 1. Excessive oil viscosity: The viscosity of the oil is closely related to its quality. The higher the viscosity, the better the oil's resistance to high temperatures, and vice versa. However, higher viscosity is not always better; you should use an oil grade that matches your engine. 2. Pressure relief valve clogged or improperly adjusted: To prevent excessive oil pressure in the lubrication system, which increases engine power consumption and causes oil leaks at sealed connections, a pressure relief valve is installed in the main oil passage or oil pump. Its function is to limit the oil pressure in the lubrication system to not exceed the specified value. A faulty pressure relief valve can cause abnormal oil pressure, triggering the oil light. 3. Engine overheating: If the engine cooling system has excessive scale, poor heat dissipation, prolonged overload operation, or if the fuel injection pump's fuel supply timing is too late, the engine may overheat, accelerating oil aging, deterioration, and thinning, leading to leakage through various clearances, pressure drop, and the oil warning light coming on.
11
5
Share

Suitable Engine Oil for the Vezel?

Vezel can use fully synthetic engine oil with a viscosity of 20. More information about fully synthetic engine oil is as follows: 1. Synthetic engine oil is manufactured by humans using chemical methods, and its composition can be adjusted according to different usage purposes. 2. Synthetic engine oil is an artificially produced lubricant. During its manufacturing process, various natural substances are chemically decomposed and then synthesized with other materials to finally produce synthetic engine oil. 3. Advantages of synthetic engine oil: higher lubricity than mineral oil, lower friction resistance, less prone to oxidation, and strong cleaning performance.
4
5
Share

How Often Should the Transmission Fluid of Rapid Spaceback Be Changed?

Under normal circumstances, the transmission fluid (ATF) of the Rapid Spaceback should be changed every two years or every 40,000 kilometers. However, this varies depending on the vehicle model. Japanese models typically recommend a change every 40,000 to 80,000 kilometers. For vehicles that frequently drive on highways, it is advisable to change the fluid approximately every 40,000 kilometers. Transmission Overview: Automatic transmission fluid cannot be completely drained using atmospheric pressure, which typically removes only about half of the old fluid. The remaining fluid, along with sludge and impurities, can accumulate in the valve body, torque converter, and cooling lines, leading to blockages in the system. Over 99% of transmission failures are caused by overheating and prolonged use of contaminated ATF. Additionally, it is important to check whether the transmission pan is deformed or if there are any leaks in the transmission lines. Owner's Note: Changing the gear oil too frequently can be counterproductive. Choosing a reputable 4S shop, understanding the cost of the fluid change, and preparing adequately can help. Delaying the change slightly may not cause significant issues, but timely replacement will benefit the vehicle in the long run.
18
4
Share

What Causes the Windshield Wiper to Not Spray Water?

Here are the reasons why the windshield wiper does not spray water: 1. Blocked spray nozzles: This is usually easy to identify. It is unlikely for both nozzles to be completely blocked at the same time or entirely clogged. The typical symptoms are reduced water flow or abnormal spray patterns. Determining whether the nozzles are blocked should be straightforward. 2. Pump overload: If the spray nozzles or water hose are blocked (e.g., due to frozen windshield washer fluid in winter), frequent activation of the washer spray can overload and damage the pump. 3. Blown fuse for the washer pump: If the water hose or spray nozzles are blocked, causing the pump to operate under excessive load, the fuse is most likely to fail first.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.