How to Replace the Air Conditioning Filter in a Reiz?

1 Answers
LeClayton
07/30/25 3:28am
Method for replacing the air conditioning filter in a Reiz: 1. Open the glove compartment on the passenger side of the car; 2. Use both hands to press inward on the glove compartment to release the clips on the sides; 3. After removing the glove compartment, you will see the outer cover of the air conditioning filter—remove the cover and take out the old filter; 4. Replace it with a new air conditioning filter and reinstall it in the original position and manner. The Reiz is the domestic name for the Japanese Toyota MARKX model. In terms of body dimensions, it measures 4750mm in length, 1795mm in width, and 1450mm in height, with a wheelbase of 2850mm.
Was this review help?
11
5
Share
More Forum Discussions

What are the symptoms of a blown engine head gasket?

Here is a detailed introduction to the symptoms of a blown engine head gasket in a car: 1. Abnormal noise at the intake pipe port: If the head gasket is damaged between two cylinders, the engine will lack power, the car will have poor acceleration and driving performance. When the air filter is removed, abnormal noise will be heard at the intake pipe port during engine idle. 2. Blue smoke from the exhaust: If the damaged part of the head gasket is connected to the oil passage, some engine oil will flow into the cylinder and burn, resulting in blue smoke from the exhaust. 3. White smoke from the exhaust: If the damaged part of the head gasket is connected to the water jacket hole, bubbles will appear in the radiator, the engine may overheat, and white smoke will be emitted from the exhaust. 4. Abnormal noise at the damaged area: If the damaged part of the head gasket is exposed to the external atmosphere, the engine's performance will deteriorate, fuel efficiency will worsen, and intense abnormal noise will be heard at the damaged area.
20
1
Share

What is the fuel consumption of the Ford Explorer 2.3t?

The fuel consumption of the Ford Explorer ranges from 11.0L to 14.0L. Below are some relevant details about fuel consumption: Factors affecting fuel consumption: Poor driving habits such as aggressive lane changes, sudden stops and starts, and driving at high speeds in low gear can all increase a car's fuel consumption. Carbon buildup in the engine can also lead to higher fuel consumption. Low tire pressure and underinflated tires can contribute to increased fuel consumption. It's advisable to check tire inflation before driving, and using a tire pressure gauge can help monitor this. Properly inflating tires can help reduce fuel consumption. Carrying excessive items in the trunk can also increase fuel consumption. Regularly clearing out unnecessary items from the trunk can help lower fuel usage. Methods to reduce fuel consumption: Maintain a steady speed while driving, avoid sudden braking and acceleration, and ensure regular vehicle maintenance.
9
3
Share

Is it necessary to install running boards on the 2019 new CR-V?

19 new CR-V has the necessity to install running boards. Below are the specific advantages and disadvantages of installing running boards: Easy to fall off: Running boards are mainly fixed with adhesive, and the quality of products on the market varies. Many inferior running boards will fall off shortly after use, and adhesive marks will remain after removal. Increased fuel consumption: Adhesive-fixed running boards cannot be retracted, increasing the width of the car. Installing running boards will make the car body heavier, thereby increasing fuel consumption. High practicality: For mid-size and large SUVs, it is necessary to install running boards. The higher ground clearance makes it convenient for the elderly and children in the family to get in and out of the car.
13
3
Share

Is 4WD Full-Time Four-Wheel Drive or Part-Time Four-Wheel Drive?

4WD stands for four-wheel drive. Below is a detailed introduction to the different four-wheel drive system modes: 1. Full-time drive: The front and rear wheels always maintain a four-wheel drive mode, with the engine output torque distributed 50:50 between the front and rear wheels during driving. Full-time drive offers excellent driving control and tracking performance but is less fuel-efficient and not very economical. 2. Part-time drive: The driver can switch between two-wheel drive or four-wheel drive mode by engaging or disengaging the transfer case based on road conditions. This is the most common drive mode for general off-road vehicles or 4WD SUVs. 3. On-demand drive: The drive mode is controlled by the computer. Normally, (front) rear-wheel drive is used on regular roads. If the road conditions are poor or the drive wheels slip, the computer automatically detects it and immediately redistributes the engine output torque to the other two wheels, switching to four-wheel drive mode. This system is simple to operate.
9
2
Share

What to Pay Attention to When Buying a Car

When buying a car, you need to pay attention to confirming purchasing power, key considerations, on-site confirmation, etc. The specific details are as follows: Confirming Purchasing Power: Determine your purchasing power to ensure that buying a car does not affect the overall quality of life for your family. Generally, this is based on the family's average income over the past three years. Typically, 20% of the family's income over three years can be allocated, but it should not exceed 10% of the family's fixed asset value. Key Considerations: For family cars, safety is the most important factor, followed by affordability. Since a car's safety carries the lives of the entire family, safety is the top priority. On-Site Confirmation: Based on the above two steps, narrow down the car models you are interested in. Visit the 4S store in person for on-site confirmation, including test drives, price inquiries, loan options, maintenance, and other related details.
15
2
Share

What is the tread depth of car tires?

Tire tread depth standards are as follows: greater than 3.5mm indicates good condition, 2.5~3.5mm is normal condition, less than 2.5mm requires replacement, and the tread must be replaced when it reaches the limit value of 1.6mm. Below is some information about car tire tread depth: 1. National regulations: According to national standards, the wear limit for radial tires used in passenger cars is 1.6mm, while the wear limit for radial tires used in trucks and buses is 2.0mm. Therefore, when the tread of a passenger car wears down to 1.6mm, it must be replaced, and tires used in trucks and buses must be replaced when the tread depth reaches 2.0mm. 2. Inspection methods: Check using the tread wear indicators built into the tire; when the tread wear indicators are flush with the tread surface, the tire needs to be replaced. Alternatively, use a tire tread depth gauge to measure the tread depth.
1
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.