How to Replace the Air Conditioning Filter for Tiggo 3

2 Answers
LeCamille
07/25/25 8:55am
Below are the steps to replace the air conditioning filter for Tiggo 3: 1. First, remove the clip located at the front of the co-pilot side in the engine compartment, then take out the sound insulation cotton. 2. Remove the filter. After taking out the sound insulation cotton, reach inside to remove the baffle. 3. Reach in again to take out the air conditioning filter. Note that there is an arrow indicator on the outer side of the filter; avoid installing it backward. Additional Information: 1. The air conditioning filter is a type of filter installed in the car's air conditioning system. It can absorb dust particles, reduce respiratory discomfort, minimize irritation for allergy sufferers, and protect the air conditioning cooling system. 2. The air conditioning filter should not be exposed to direct sunlight; it should be dried before reinstallation. If it is excessively dirty, replacement is recommended. Generally, the air conditioning filter should be replaced every two minor maintenance intervals, approximately every 10,000 kilometers, depending on the condition of the filter.
Was this review help?
10
0
Share
Ricky
08/10/25 7:06pm
I previously replaced the air conditioning filter of my Tiggo 3 by myself, and the whole process was quite hassle-free, mainly involving operations in the glove compartment on the passenger side. First, park the car and turn off the engine, then open the glove compartment. There are plastic clips on both sides; pressing them allows for easy removal. Inside, there's a small cover plate usually secured by two small cross screws—remove them with a screwdriver. After taking it off, you can see the old filter. Pull it out and remember the direction of the arrow; when installing the new one, make sure the arrow points in the same direction as the airflow to avoid reduced air volume or compromised AC performance. I overlooked the direction the first time I replaced it, resulting in slower airflow, and had to redo it twice to get it right. After replacement, reassemble all parts—it's very simple. It's recommended to replace the filter every six months. Buying one online costs only 30-50 RMB, and choosing an activated carbon filter offers better filtration. Doing it yourself saves over 200 RMB in labor costs at a repair shop and ensures clean filtration of dust and pollen, making the air in the car fresher. Remember to wear gloves to keep your hands clean; the entire process takes no more than 15 minutes.
Was this review help?
12
5
Share
Expand All
More Forum Discussions

How to Tell If Engine Oil Level is Increasing?

Methods to check for increased engine oil level: 1. Park the car on a relatively flat surface, turn off the engine and wait for more than five minutes to allow the oil to completely flow back. It is recommended to perform the measurement at the same parking spot each time; 2. Open the engine compartment, locate the oil dipstick, pull it out, and check if the oil level is between the two marks on the dipstick; 3. To ensure accuracy, first wipe the dipstick clean with a paper towel, then reinsert it into the engine. Oil level increase commonly occurs in direct injection engines and is often observed during winter. In direct injection engines, fuel is directly injected into the cylinder, unlike port fuel injection where there is more time for the fuel to mix with air. Some fuel may be sprayed onto the cylinder walls, causing wetting.
18
2
Share

Where is the VIN number located on a smart car?

smart car's VIN number is located at the lower right corner of the front windshield. For vehicle inspection purposes, the VIN to be imprinted should be found in front under the front passenger seat - just lift the panel to locate it. The VIN (Vehicle Identification Number) is a unique 17-character alphanumeric code that identifies a vehicle's manufacturer, engine, chassis number, and other specifications. smart is a microcar brand under Mercedes-Benz, with dimensions of 2695mm in length, 1663mm in width, and 1555mm in height, featuring a wheelbase of 1873mm. In terms of suspension, the smart car uses MacPherson strut independent suspension at the front and torsion beam semi-independent suspension at the rear.
18
1
Share

How to adjust the time on Chery QQ3?

Chery QQ3 time adjustment method: 1. Press and hold the SEL button for 2 seconds until SET flashes to enter the setting mode, then briefly press both SEL and TRIP buttons simultaneously to enter clock initialization mode; 2. When the clock flashes, press the TRIP button to adjust the hour value. After setting the hour, press SEL to enter minute adjustment mode, then use TRIP to adjust minutes; 3. After completing adjustments, briefly press both SEL and TRIP buttons simultaneously to finish time setting. The Chery QQ3 is a microcar under Chery Automobile, with dimensions of 3550mm in length, 1495mm in width, and 1485mm in height, featuring a 2340mm wheelbase. For suspension, the front adopts MacPherson strut independent suspension while the rear uses longitudinal trailing arm semi-independent suspension.
17
4
Share

How to Steer the Wheel When Driving on Curves?

Steering techniques for curve driving: 1. When entering a left curve, keep the vehicle close to the right line before turning the wheel to the left; 2. When entering a right curve, keep the vehicle close to the left line before turning the wheel to the right; 3. When the right front corner of the car touches the right line, turn the wheel one full turn to the left, keeping the left front corner at a certain angle to the line on the ground to follow the right line of the first S-curve, preventing the car from crossing or touching the line; 4. When exiting a left curve, turn the wheel half a turn to the right as the front wheels just leave to avoid the rear wheels touching the line; 5. When exiting a right curve, turn the wheel half a turn to the left as the front wheels just leave to avoid the rear wheels touching the line.
11
0
Share

Which Mazda models feature rotary engines?

Mazda models equipped with rotary engines belong to the RX series, while other models do not utilize this engine type. The rotary engine offers advantages such as achieving high RPMs without requiring precise crankshaft balancing, compact size, lightweight construction, and significantly simplified architecture. Taking the Mazda RX7 as an example: The Mazda RX7 is a sports car under the Mazda brand, with dimensions of 4430mm in length, 1770mm in width, and 1340mm in height. In terms of power, the Mazda RX7 is equipped with a twin-turbocharged 13B-REW rotary engine, delivering a maximum output of 195 kW and peak torque of 294 Nm, paired with a 5-speed manual transmission.
2
3
Share

What is the correct way to use the one-button start in Volkswagen Touran?

Correct method for using the one-button start in Volkswagen Touran: Press the brake pedal and then press the button once to start the engine. The same applies for turning off the engine - press the button once to shut it down, but make sure the gear is in P position. The one-button start is a component of smart car systems, serving as a button device that simplifies the ignition process while also allowing engine shutdown. This feature can be retrofitted either at the original key lock position or as an independent panel. The Volkswagen Touran is an MPV model under SAIC Volkswagen, with dimensions of 4395mm in length, 1794mm in width, and 1634mm in height, along with a wheelbase of 2678mm. In terms of suspension, the front suspension adopts MacPherson strut independent suspension, while the rear uses a four-link independent suspension system.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.