How to Replace a Lost Vehicle License?

2 Answers
SanTimothy
07/25/25 2:59am
You must drive to the vehicle management office, and new photos of the vehicle are required. Three vehicle photos; a power of attorney and the identity proof of the authorized person. You need to bring your "Motor Vehicle Registration Certificate", the owner's ID card, and copies. Provide the original and copies of the vehicle license and the identity proof of the vehicle owner. Apply for replacement at the vehicle management office where the vehicle is registered. When applying, the vehicle owner should fill out the application form and submit the identity proof. The vehicle management office should reissue the vehicle license within one day from the date of acceptance.
Was this review help?
7
1
Share
LondynLynn
08/10/25 4:48pm
I was so worried when I lost my vehicle license last time! I immediately called the DMV staff for advice, and they said the replacement process is actually quite convenient. The most important thing is to bring your original ID card and the vehicle registration certificate (that green booklet), then just fill out an application form at the DMV. Remember you must go in person because they need to verify your facial information. Pay a 10-yuan processing fee on site, and the staff will print a new license for you immediately - the whole process usually takes about half an hour. One important detail: If your car was purchased with a loan and the registration certificate is mortgaged, you'll need to contact the bank for a certificate first before applying for replacement. My colleague mentioned that some places now allow appointments via the 12123 APP to avoid queuing, but it's still safer to bring cash just in case.
Was this review help?
15
3
Share
Expand All
More Forum Discussions

What is the fuel consumption of the Mustang?

The fuel consumption of the Mustang is approximately 14 liters per 100 kilometers. Here is some information about the Mustang's fuel consumption: Market segment: The GT500 typically consumes about 16 liters per 100 kilometers. The Ford Mustang, as a model that attracts the attention of many car enthusiasts, has a high market share worldwide. For a long time, there were no official agents in China, and purchases had to be made through individual agents without warranty coverage. However, there are now general agents in mainland China. Exterior introduction: The current model available from the company is the 2011 new version. The new Mustang retains its classic muscle car lines while adding many curved lines, making the vehicle appear more resolute, robust, and visually impactful. The front-end design has a noticeable forward-leaning tendency, and the turn signals have been moved into the headlight assembly. The hood has been completely redesigned, with the center section prominently raised, hinting at its powerful engine.
16
5
Share

How to Step on the Accelerator Correctly for Better Fuel Efficiency?

During normal driving, car owners should achieve fuel savings by stepping on the accelerator steadily and continuously. Here are some related tips for fuel-efficient driving: Close the windows when driving at high speeds: When driving at high speeds with the windows open, the vehicle experiences significant air resistance, leading to a substantial increase in fuel consumption. Besides closing the windows, it's advisable to set the air conditioning temperature around 20 degrees Celsius to reduce the working time of the air conditioning compressor, thereby enhancing fuel efficiency. Maintain a steady speed: Driving at a constant speed allows for complete fuel combustion, which not only enhances vehicle power but also significantly improves fuel efficiency. It's best to avoid sudden acceleration and braking to save fuel effectively. Avoid carrying unnecessary items in the car: Data shows that carrying an extra 10 kilograms of miscellaneous items for a thousand kilometers can consume an additional 1 liter of gasoline, leading to unnecessary waste.
13
4
Share

Differences Between 18-inch and 19-inch Wheels

The differences between 18-inch and 19-inch wheels are mainly reflected in the size, manufacturing cost, price, driving comfort, and fuel consumption. The specific details are as follows: 1. Size: Inch refers to inches, with 1 inch equal to 2.54 centimeters. An 18-inch wheel has a diameter of 45.72 centimeters, slightly smaller than a 19-inch wheel. 2. Manufacturing cost: The amount of material used differs, with 19-inch wheels having a higher manufacturing cost than 18-inch wheels. 3. Price: For the same model of wheel, the larger the size, the higher the price. 4. Driving comfort: Larger wheels with thinner sidewalls provide more realistic feedback from the road during driving. Smaller wheels with thicker sidewalls can effectively filter out road vibrations, making 18-inch wheels more comfortable. 5. Fuel consumption: Larger wheels with wider treads increase friction with the ground, leading to higher fuel consumption. For the same car, using 19-inch wheels will consume more fuel than using 18-inch wheels.
6
0
Share

How to Deal with Abnormal Noises from Car Doors?

Here are the solutions for abnormal noises from car doors: 1. Check if the noise is caused by the inner pull wire hitting the door panel. If so, remove the door trim panel and wrap the inner pull wire with a small piece of sponge. 2. Aging seals can also produce noises, which can be resolved by replacing them with new ones. Inspect the door hinges; if the friction increases and causes noise, you can spray rust inhibitor and then apply an appropriate amount of grease. Additional Information: Abnormal noises caused by the inner wiring harness hitting the door panel: When driving on bumpy roads, the inner wiring harness may hit the door panel, resulting in continuous noise. When the door seals are used for a long time, they gradually age, causing friction between the seals and the car body, which may produce abnormal noises while driving. Abnormal noises caused by the door limiter: If the door limiter is not regularly maintained, it can also cause abnormal noises. The solution is to apply some grease and spray automotive rust inhibitor, which will significantly reduce the friction of the door limiter and resolve the abnormal noises.
18
3
Share

What does a wrench symbol on the car display mean?

When a wrench symbol appears on the car dashboard, it is a maintenance reminder light, alerting the owner to perform maintenance at a 4S shop. Here are the details: 1. After the vehicle has been driven for a certain mileage, the maintenance reminder light alerts the driver to perform maintenance. 2. Note that different manufacturers set different maintenance intervals for their models, so refer to the vehicle's user manual for specifics. 3. After maintenance is completed, the technician will reset the maintenance light to zero through a setting procedure. If the vehicle is properly maintained, the "small wrench" symbol can be manually cleared as follows: 1. Insert the key, but do not turn it. 2. Press and hold the operation lever next to the odometer for 5–10 seconds, then turn the key to power on the vehicle. 3. After another 5–10 seconds, start the engine. Keep holding the operation lever throughout this process. 4. Generally, following these steps will clear the wrench symbol. If it does not clear, repeat the process a few more times.
1
2
Share

How to Recommend Car Audio Modifications?

There is a saying that fits particularly well: wear shoes that fit your feet. The same goes for car audio modifications. Tailoring the audio upgrade to your actual needs not only fulfills your desires but also avoids unnecessary financial strain. Choosing a car audio modification shop is crucial—30% depends on the equipment, while 70% relies on the technician's skill. The same audio products installed by different professionals can yield vastly different results. Underestimating the shop's expertise can lead to issues, especially concerning electrical circuits. Always opt for a shop with professional experience in car audio modifications. Reserving space for audio components is often overlooked. The modification process should be gradual: start by replacing speakers, upgrade the amplifier, add bass-enhancing speakers, and then replace the head unit. Ignoring space reservation can negatively impact audio quality, so it's best to leave room for future upgrades. Overlooking the head unit's amplifier capacity is another common mistake. Many enthusiasts focus heavily on achieving deep bass, investing heavily in amplifier tuning. While initial tests may sound good, unstable battery voltage can degrade sound quality. High-power amplifiers risk overheating and burning circuits, a leading cause of spontaneous combustion in audio modifications.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.