How to Replace a Driver's License When the Address Differs from the ID Card?

1 Answers
StKylie
07/30/25 5:58am
Within ninety days, bring your original driver's license, original ID card, and photocopies to the service window of the local vehicle management department to submit an application. When submitting the application, you will need three personal ID photos. If you don't have them, you can take photos at the vehicle management office on the same day and collect the photos. Go to the designated medical examination hospital by the local vehicle management department, verify that the ID card matches your identity, and undergo a medical examination after providing the photos to obtain a physical condition certificate. Organize the above-mentioned supporting documents and bring them to the local vehicle management department to collect and fill out the motor vehicle driver's license application form at the service window. After the staff verifies the relevant documents and confirms they are correct, pay the fee for replacing the motor vehicle driver's license. The new driver's license can be collected within 2-3 working days.
Was this review help?
6
1
Share
More Forum Discussions

Can You Start in Second Gear with a Manual Transmission?

Manual transmission vehicles can start in second gear, but this method is not recommended. Hazards of starting in second gear: Frequently starting in second gear can damage the clutch. Starting in second gear may result in insufficient engine speed, causing more wear on the clutch plate. The higher the gear used for starting, the greater the wear on the clutch. Standard starting method: When starting, you should slowly release the clutch pedal while gradually pressing the accelerator. The clutch pedal can be released slightly faster than the accelerator. Once the vehicle begins to vibrate or shows signs of movement, increase the speed of pressing the accelerator first, then speed up the release of the clutch pedal until the vehicle starts smoothly.
4
0
Share

Which month of 2017 registered vehicles are China V compliant?

All vehicles produced in 2017 comply with the China V emission standard. Nationwide, there are currently no traffic restriction policies targeting China V emission standard vehicles. Specific details are as follows: 1. China V implementation time: China's China V emission standard was implemented nationwide on January 1, 2017, representing an upgrade from the China IV standard. 2. China V emission limits: Carbon monoxide emissions must not exceed 1000mg/km; Non-methane hydrocarbons must not exceed 68mg/km; Nitrogen oxides must not exceed 60mg/km; PM particulate matter must not exceed 4.5mg/km; PN particulate matter must not exceed 6x10^11mg/km.
9
4
Share

What causes a car to fail to start immediately after being turned off?

There are four main reasons why a car may fail to start immediately after being turned off: throttle valve malfunction, fuel pump failure to supply gasoline, timing belt breakage, and coolant temperature sensor failure. Excessive carbon buildup on the throttle valve or idle speed motor may cause the engine to stall. When the throttle position sensor malfunctions, the inaccurate data received by the sensor typically leads to excessively high engine idle speed and may also cause the engine to stall. Stalling, also known as quenching, occurs when a reactor operating at a significant reaction rate suddenly experiences a drastic drop in reaction speed when the feed inlet temperature is reduced to the lower limit of the multiplicity region, causing the reaction to essentially stop. This phenomenon is called quenching.
13
5
Share

Does spraying insecticide on a car affect the paint?

Spraying insecticide on a car will not affect the paint. Here are some car paint maintenance methods: 1. Remove dust from the car body: Before, during, and after using the vehicle, promptly remove dust from the car body to minimize the adsorption of dust by static electricity on the body. 2. Rinse promptly after rain: Rain stains on the car body after rain will gradually shrink, increasing the concentration of acidic substances in the rainwater. If not rinsed with clean water as soon as possible, these stains can damage the paint over time. 3. Avoid washing the car in direct sunlight or high temperatures: When washing the car, wait until the engine has cooled down. Do not wash the car under direct sunlight or in high temperatures to prevent the cleaning agent from drying out and leaving marks.
1
0
Share

Should the fuel tank cap connecting wire be replaced if it's broken?

The fuel tank cap connecting wire needs to be replaced if it's broken. Below are the functions of the fuel tank cap drain hole: 1. Facilitate drainage: There is a drain hole under the fuel tank cap, usually located on the inclined surface of the fuel tank opening. Its primary purpose is to facilitate drainage, as accumulated water could easily flow into the fuel tank, potentially contaminating the gasoline. 2. Protect the engine: Accumulated water can cause significant damage to the car's engine, so the drain hole plays a crucial protective role, extending the engine's lifespan.
12
2
Share

How to Reset the Maintenance Light on BYD Tang?

Method to reset the maintenance light on BYD Tang: 1. On the central dashboard display menu interface, briefly press the steering wheel's right-side scroll wheel to select the driving information interface; 2. Scroll the wheel to choose the maintenance information interface, then press and hold the scroll wheel. The BYD Tang is a mid-size SUV under the BYD brand, with exterior dimensions of 4870mm in length, 1940mm in width, and 1720mm in height, and a wheelbase of 2820mm. The BYD Tang is equipped with a 2.0T turbocharged engine, paired with a 6-speed automatic transmission, delivering a maximum horsepower of 192 HP, a maximum power of 141 kW, and a maximum power speed of 5500 RPM.
2
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.