How to Replace a Car Tire?

What is the fuel tank capacity of the Mercedes-Benz GLB?

The fuel tank capacity of the Mercedes-Benz GLB is 66 liters, and the manufacturer recommends using 95-octane gasoline. Fuel tank maintenance is as follows: Drain accumulated water and sediment from the fuel tank, and check for oil leaks at pipe joints and switches. For fuel tank caps equipped with air valves and steam valves, also check if the ventilation holes are clear. The filter screen at the fuel filler should remain intact to prevent impurities from entering the tank and clogging the fuel lines during refueling. The sealing gasket of the fuel filler cap should also be intact to prevent fuel spillage while driving. If the owner wants to know the remaining fuel level, they can observe the fuel gauge on the right side of the instrument panel, which is marked with E and F. When the pointer is near E, it indicates low fuel, and when it is close to F, it means the fuel level is sufficient. Methods to open the fuel tank: Mechanical key opening: This method is commonly seen in some rugged off-road vehicles but is generally not used in modern family cars. In-car switch method: The position of the in-car fuel tank switch varies depending on the vehicle model. Remember to turn off the engine before refueling. Press-to-open method: The press-to-open fuel tank door is currently the most convenient method.

9

2

Share

What does it mean when the EPC light appears on the car dashboard?

The EPC indicator light can illuminate in two scenarios: during the power-on self-test and under other conditions. The power-on self-test is an indication that the vehicle is checking the status of all sensors before driving. Generally, if the engine is not started after power-on, the light will turn off by itself after about 3 seconds. In other cases, if the EPC light remains illuminated after the vehicle starts or stays on for an extended period, the possible causes include faults in the engine intake system, throttle issues, fuel system problems, engine malfunctions, ECU control unit failures, or brake light issues. Below is a detailed explanation of the reasons for the EPC light illuminating under other conditions: Engine intake system fault: The EPC light will activate if the engine intake is obstructed or insufficient. Throttle fault: Carbon buildup is a common issue with the throttle. Additionally, dirt accumulation can affect intake, triggering the indicator light. Fuel system fault: This includes issues such as substandard fuel, fuel deterioration, or poor fuel atomization. Engine fault: Insufficient engine pressure or problems with components like the intake valves can also cause the EPC light to illuminate. ECU control unit fault: Examples include interference with the onboard computer signals or false alarms from the onboard computer. Brake light fault: Situations like non-functional brake lights, faulty brake switches, or brake circuit issues. Solutions for when the EPC light illuminates: Troubleshoot intake system issues, use fuel with the appropriate octane rating, clean the throttle, etc. Remove carbon deposits from relevant components. Re-flash the ECU with updated data. If the EPC light comes on, the driver can first try turning off the engine and restarting it to see if the light remains off. If it does not reappear, there may be no issue, and the EPC light might have been affected temporarily. However, if the light stays on or frequently illuminates, the vehicle should be taken to the nearest service center for professional diagnosis and repair to eliminate potential safety hazards. The full English name of EPC is Electronic-Power-Control, which translates to electronic power control. Most people refer to it as the engine electronic stability system. The EPC system primarily includes controllers and sensors related to the powertrain. When sensor data deviates from normal values, the EPC system takes predefined actions to manage the powertrain. Common EPC indicator lights typically display two colors: yellow and red. A yellow EPC fault light indicates that the vehicle can still be driven, but it should proceed slowly to a repair facility for inspection. A red EPC fault light signifies a more severe issue, requiring immediate pulling over and contacting a professional for repairs. Continuing to drive under such conditions could damage core components or compromise driving safety.

18

0

Share

What does the ECON indicator on the car mean?

ECON is the switch for the car's fuel-saving mode, which can be turned on or off by pressing this button. Modern cars generally offer three driving modes to choose from: Eco mode, Comfort mode, and Sport mode. Here is information about these three modes: Eco mode: When the car is in this mode, fuel consumption is relatively low. The throttle pedal sensitivity decreases, and the transmission shifts up more aggressively. Comfort mode: This mode is considered a normal operating mode for the car. In this mode, the throttle pedal response is more sensitive than in Eco mode. Sport mode: Sport mode can be used during aggressive driving. When Sport mode is activated, the throttle pedal becomes highly responsive, and the transmission delays shifting. The transmission only upshifts when the engine speed reaches the redline. In Sport mode, the engine speed is maintained at around 3,000 RPM, ensuring better power response during acceleration. When the car enters ECON mode, it achieves reduced fuel consumption and energy savings, but the vehicle's power output is weakened. ECON can be understood as an abbreviation for 'economy.' In most cases, it is recommended to keep ECON mode enabled. However, it should be turned off when high torque output is required (e.g., when climbing a hill) or when driving at very high speeds. Pressing the ECON button activates a low-carbon, eco-friendly driving mode. The ECU, engine, and transmission then operate intelligently in the most fuel-efficient manner, achieving optimal fuel economy through rapid upshifts and smooth acceleration. The air conditioning system also operates in an energy-saving state. When the driver presses the throttle pedal deeply, the ECON system effectively controls the opening and closing of the intake valves to ensure smooth engine operation and energy efficiency. Although ECON mode is simple and effective, it does not work under certain conditions: When the vehicle speed exceeds 120 km/h, priority is given to speed, and the Eco mode automatically deactivates. This means that if the car exceeds the economical speed range (typically between 60-90 km/h), ECON mode will not save fuel. The key to ECON mode is the independent operation of the car's computer while driving, making it effective. Therefore, ECON does not function during idle parking or when the car is in N, P, or manual mode. When overcoming significant resistance or requiring high torque output (e.g., when climbing a hill), the ECU prioritizes ensuring sufficient power to drive the car, and ECON mode will not operate in such cases.

15

2

Share

What Causes Normal Low Pressure but Low High Pressure in Car Air Conditioning?

When a car's air conditioning system exhibits low low-side pressure and normal high-side pressure, it is typically caused by a malfunction or failure of the air conditioning compressor. Below is a detailed explanation of this issue: 1. For compressor failure leading to normal low pressure but low high pressure, the solution generally involves replacing the air conditioning compressor with a new one. 2. Due to the cramped and compact space around the car's air conditioning compressor, disassembly is quite inconvenient. Additionally, temporary recovery of the refrigerant is required, making the process labor-intensive. It is recommended to have this service performed at a 4S dealership.

10

0

Share

What to Do When Audi Parking Assist System Fails?

Audi parking assist system failure solutions are as follows: 1. Excessive brake clearance: The contact area between the brake shoe and drum is too small, oil contamination or hardening on the brake shoe or pad, exposed rivets, severe deformation of the brake drum or disc. In this case, reduce the contact area or replace the rivets and repair the brake drum. 2. Control mechanism issues: Worn and loose components in the control mechanism, excessive clearance, or overly long cables. In this case, replace the control mechanism components, reduce the clearance, shorten the cables. During repairs, it is essential to proceed carefully, preferably with professional assistance.

14

2

Share

Where is the jack of Wuling Hongguang S?

Car jacks are generally placed in the trunk or toolbox. The following is a related introduction to the jack: 1. Support points: Near the wheel positions on both sides of the vehicle chassis, there are support points for the jack to contact. 2. Note: Generally, there is a protruding long edge on the bottom edge of the vehicle, and there will be several thickened positions on this long edge for placing the jack. When using the jack to lift the car, it is essential to choose a solid and level road surface, and the handbrake must be firmly engaged. 3. Position: The lifting part of the jack must be supported on the chassis support points; otherwise, it will be difficult to stabilize the vehicle, and it may easily damage the jack or even the chassis.

10

3

Share

How to Replace a Car Tire?

What is the fuel tank capacity of the Mercedes-Benz GLB?

What does it mean when the EPC light appears on the car dashboard?

What does the ECON indicator on the car mean?

What Causes Normal Low Pressure but Low High Pressure in Car Air Conditioning?

What to Do When Audi Parking Assist System Fails?

Where is the jack of Wuling Hongguang S?

What is the normal tire pressure for BMW?

What is the battery model for the Chang'an Suzuki Swift?

How Long Does It Take to Inspect a Car at the DMV?

What Causes Engine Shaking and Stalling?