How to Repair a Dent in an Aluminum Car Panel?

How many seconds after stalling in Subject 3 is considered a failure?

As long as the vehicle stalls, it is considered stalling regardless of the duration. If the engine stalls due to improper operation, 10 points will be deducted once. However, no further mistakes can be made in the subsequent operation process; otherwise, the test will not be passed, and a retake will be required. Relevant information: 1. Main reason: Lifting the clutch too quickly when starting. If the clutch is lifted too quickly, the engine's output power and the transmission input shaft's power are not proportional, causing a sudden increase in friction, which leads to stalling. 2. Difficulties in Subject 3 test: Mismatch between speed and gear, deviation in straight-line driving, and parking more than 30cm away from the curb.

9

1

Share

How to Turn Off the Auto Start-Stop Function on the Buick Envision

The auto start-stop button for the Buick Envision is located on the right side of the center console screen. When the light is on, the auto start-stop function is enabled; pressing the button to turn off the light will disable the auto start-stop function. Additional information about the Buick Envision is as follows: 1. How the Buick Envision's engine start-stop system works: When the vehicle stops moving due to traffic congestion or at an intersection, the driver presses the brake pedal and shifts into neutral. At this point, the Start/Stop system automatically checks: the engine is idling and not in gear; the system's wheel speed sensor shows zero; the electronic battery sensor indicates sufficient energy for the next start. Once these three conditions are met, the engine automatically stops. When the driver shifts into gear and presses the accelerator, the engine restarts and continues to operate. 2. Car idling: The auto start-stop technology is primarily used in traffic congestion situations, where the engine is usually warm, and the fuel consumption of a warm engine starting is minimal. The engine can typically start at 350 rpm, which is nearly half the idle speed. Assuming there are no other loads besides the engine's internal resistance during the start-up process and the necessary equipment such as the transmission's loss, the fuel consumption is certainly less than during idle conditions.

6

0

Share

What is the purpose of capturing photos in Subject 2?

During practice for Subject 2, it is mandatory to capture a photo. This photo must be uploaded to the vehicle management department's backend system as one of the evidences for practice sessions, and it is also used to check for any violations during the practice. Without this captured photo, the practice hours might be deemed invalid during the review process due to the lack of photographic evidence. Related information: 1. Photo capture rules: The photo must clearly identify facial information, show the seatbelt being worn, and ensure that hands are not improperly placed on the steering wheel. 2. Attendance rules: The driving school issues an attendance card to each student to record the check-in time.

12

4

Share

What Causes the Brake Pedal to Not Depress and the Engine to Not Start with One-Button Start?

Possible reasons: The car is out of fuel, the battery is faulty, or the spark plug is malfunctioning. Below are the relevant details: 1. Battery: A battery is a type of cell, also known as an accumulator, which works by converting chemical energy into electrical energy. The battery commonly referred to is a lead-acid battery, which mainly uses lead and its oxides as electrodes and sulfuric acid solution as the electrolyte. 2. Spark Plug: The spark plug is a crucial component of the gasoline engine's ignition system. It introduces high voltage into the combustion chamber, causing a spark to jump across the electrode gap, thereby igniting the combustible mixture in the cylinder. It mainly consists of a terminal nut, insulator, terminal stud, center electrode, side electrode, and shell.

8

2

Share

How long does it take to customize a car on FAW-Volkswagen Mall?

It takes approximately more than 20 days to customize a car on FAW-Volkswagen Mall. Below is the relevant information: 1. Volkswagen: FAW-Volkswagen Automotive Co., Ltd. was established on February 6, 1991. It is a large passenger vehicle production enterprise jointly operated by China FAW Corporation Limited, Volkswagen AG, Audi AG, and Volkswagen (China) Investment Co., Ltd. It is the first modern passenger vehicle production enterprise in China to start construction according to economic scale. 2. FAW: China FAW Group Corporation (referred to as FAW Group, China FAW, or FAW, with the English name FAW) is located in Luyuan District, Changchun City, Jilin Province, China. Its predecessor was the First Automobile Works, with the factory name personally inscribed by Chairman Mao Zedong and founded by Rao Bin. The foundation was laid on July 15, 1953.

18

2

Share

What kind of engine oil should be used for Honda XRV 1.8?

Honda XR-V 1.8L engine models can use 0W20 engine oil. This type of oil is low-viscosity. Due to the compact structure of the engine, the distance between the internal components is small. Low-viscosity oil can save fuel and is sufficient to allow the engine to perform at its best. Here are a few simple methods to judge the quality of engine oil: 1. Hand-rubbing method: Rub the lubricating oil repeatedly between your thumb and index finger. Good lubricating oil should feel smooth, with few wear particles and no friction. If you feel significant friction like sand particles between your fingers, it indicates that the lubricating oil contains many impurities and should be replaced. 2. Light inspection method: On a sunny day, use a screwdriver to lift the lubricating oil at a 45-degree angle to the horizontal plane. Observe the oil droplets under sunlight. If you can clearly see no wear particles in the lubricating oil, it is in good condition and can continue to be used. If there are excessive wear particles, the lubricating oil should be replaced. 3. Oil drop trace method: Take a clean white filter paper and drop a few drops of oil on it. After the lubricating oil has seeped through, if there are black powders on the surface and it feels rough to the touch, it means the lubricating oil contains many impurities. Good lubricating oil should have no powders, feel dry and smooth to the touch, and leave a yellow trace.

18

3

Share

How to Repair a Dent in an Aluminum Car Panel?

How many seconds after stalling in Subject 3 is considered a failure?

How to Turn Off the Auto Start-Stop Function on the Buick Envision

What is the purpose of capturing photos in Subject 2?

What Causes the Brake Pedal to Not Depress and the Engine to Not Start with One-Button Start?

How long does it take to customize a car on FAW-Volkswagen Mall?

What kind of engine oil should be used for Honda XRV 1.8?

What is the tire size of the classic Sylphy?

What are the techniques for operating the clutch when learning to drive?

What to Do When the Dashboard Shows High Temperature Warning?

Is the Ora Black Cat an Electric Vehicle or a Car?