How to Renew a Driver's License in a Different Location After Expiry?

1 Answers
LeSkylar
07/30/25 4:25am
Methods for renewing an expired driver's license in a different location: 1. When applying, fill out the "Motor Vehicle Driver's License Application Form" and submit the identity proof of the motor vehicle driver and the motor vehicle driver's license; 2. First, prepare the expired driver's license, three 1-inch color photos, a valid ID card, and a copy of the ID; second, undergo a physical examination; third, review and renew the license; fourth, receive the new license; 3. Those applying for a new version of the driver's license can provide their own photos, which must meet the requirements. Four conditions must be met to renew a driver's license: 1. No more than 12 points should have been accumulated in each scoring cycle before renewal; 2. All violations before renewal must be handled, fines paid, and points cleared; 3. The driver's physical condition must meet the driving permit conditions. (Reminder: Drivers over 70 years old must submit a physical proof annually.) 4. The renewal application can only be submitted within three months before the driver's license expires.
Was this review help?
10
5
Share
More Forum Discussions

When to Use Hazard Warning Lights in a Car?

Hazard warning lights in a car should be used in the following situations: 1. During temporary parking; 2. When the vehicle breaks down or is involved in a traffic accident; 3. When towing a faulty motor vehicle; 4. When forming a convoy approved by traffic police authorities. How to activate hazard lights: The hazard light switch is independently located, usually represented by a red triangle symbol. Pressing it once activates the hazard lights. Most hazard light switches are positioned on the dashboard to the right of the steering wheel, though some models may have the switch located below the dashboard. Hazard lights, also commonly referred to as emergency flashers, serve as signal lights on vehicles, primarily to alert other drivers and pedestrians that the vehicle is experiencing special circumstances, prompting them to yield in time.
11
3
Share

Where is aluminum alloy used in the BMW X3 body?

BMW X3's hood, the fenders on both sides of the front wheels, and the front doors on both sides of the vehicle are made of aluminum alloy. The exterior design of the X3 also follows BMW's family style, resembling its bigger sibling, the X5. The recently redesigned X1 has adopted a similar design. Compared to the Q5L, the X3 features more muscular lines in its appearance, along with more chrome and black trim. Below is additional information about aluminum alloy bodies: 1. An all-aluminum body is lighter than a conventional steel body, typically by more than 30%. Aluminum bodies are easier to press, allowing for one-piece stamping with fewer welding points, resulting in higher body strength and less deformation. 2. However, the manufacturing process requires higher technical standards, and the material costs are significantly higher. While all-aluminum bodies have advantages, they also have drawbacks, primarily being more brittle compared to conventional steel bodies. 3. This is due to the higher hardness, so generally, after a high-intensity collision, an all-aluminum body may need to be scrapped, unlike conventional vehicles that can undergo body repair.
8
2
Share

Is the recommended oil grade for the new Bora 5W30 or 5W40?

The factory-recommended oil grade for the Bora is SM5W-40 semi-synthetic oil. For later maintenance oil changes, you may choose reputable international brands such as Shell, Castrol, and Mobil, or domestic brands like Great Wall, Kunlun, and Tongyi. The official Bora manual recommends using SM or higher grade 5W-40 oil, or oil that meets the VW50200 standard. Oil viscosity changes with temperature, so special attention should be paid to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, resulting in smoother cold starts for the vehicle. The second number represents the oil's kinematic viscosity at 100°C. A higher value indicates better ability to maintain viscosity under high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the Bora's oil is as follows: Wait for the engine temperature to drop, allowing the oil to flow back into the oil pan; Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops flowing. Start the engine and let it run for 30 seconds to allow the oil in the main oil passage to drain out; Use a special wrench to remove the oil filter; Apply oil to the seal of the new oil filter and tighten it clockwise by hand; Add new oil through the engine valve cover filler port, typically filling about three-quarters of a standard oil bottle; Start the engine and let it run for 5 minutes, then check for oil leaks around the drain plug and oil filter. If any leaks are found, perform necessary repairs; After stopping the engine, pull out the oil dipstick to check that the oil level is within the standard range.
2
4
Share

Does the dash cam consume a lot of power when left on all the time?

The dash cam does consume power when left on continuously, but the power consumption is minimal. In reality, the dash cam enters a dormant state when the vehicle is parked. It only activates to record for 5 to 10 seconds when it detects vibrations from the vehicle, then returns to the dormant state, resulting in very low power consumption. Dash cams are mainly divided into two categories: portable dash cams and integrated aftermarket DVD dash cams. Portable dash cams can be further classified into rearview mirror dash cams and data dash cams, which are known for their discreet appearance, easy installation, detachable and replaceable features, and simple operation. Integrated aftermarket DVD dash cams are vehicle-specific and can be categorized into pre-installed and aftermarket types. Installing these dash cams can be more challenging, but they help maintain the vehicle's interior aesthetics. Additionally, some luxury car models come with factory-installed dash cams.
12
2
Share

How to use the Haval H6 navigation system?

Steps to use the Haval H6 navigation system: 1. Enter the navigation interface and search for the destination; 2. Set the route and start navigation. The Haval H6 is the flagship model of the Haval brand, positioned as an urban intelligent compact SUV with dimensions of 4640mm in length, 1825mm in width, and 1690mm in height, and a wheelbase of 2738mm. The Haval H6 is equipped with a 2.0T 211 horsepower L4 turbocharged engine, paired with a 7-speed dual-clutch transmission. For safety, it features a standard 71.61% high-strength steel body, hot-formed steel integrated door frames, and 6 airbags. The front suspension uses a MacPherson independent suspension, while the rear suspension employs a double-wishbone independent suspension.
15
0
Share

How soon can I retake the test if I fail the third subject?

If you fail the third subject, you can only schedule a retake after ten days. The third subject includes the road driving skills test and the safe and civilized driving knowledge test, which are part of the motor vehicle driver's license assessment. It is the abbreviation for the road driving skills and safe and civilized driving knowledge test in the motor vehicle driver's examination. The road driving skills test is divided into 16 items: vehicle preparation, starting, driving in a straight line, shifting gears, turning left at intersections, turning right at intersections, changing lanes, passing through intersections, pulling over, crossing pedestrian crossings, passing school zones, passing bus stops, meeting other vehicles, overtaking, making U-turns, and night driving.
7
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.