How to Remove the Wrench Icon on Fengjun 5?

1 Answers
DanteMarie
07/29/25 7:31pm
Fengjun 5 wrench icon removal method is as follows: 1. Turn on the ignition (no need to start the engine). 2. Switch the mode to display instant fuel consumption status. 3. Turn off the ignition. 4. While holding the mode button, turn on the ignition again and then release the button. 5. Press both the mode button and the left time adjustment button simultaneously to remove the wrench icon. More information about Fengjun 5 is as follows: 1. Fengjun 5 is a pickup truck under Great Wall, equipped with a 2.8T engine to meet the needs of carrying passengers and cargo. 2. The new vehicle is equipped with 2.0T diesel engine, 2.5T diesel engine, 2.8T diesel engine, and 2.2L, 2.4L gasoline engines, matched with a 5-speed manual transmission.
Was this review help?
10
0
Share
More Forum Discussions

What is the installation method for the timing belt of the Qashqai?

The installation method for the timing belt of the Qashqai is as follows: 1. Align the mark on the camshaft timing gear with the mark on the valve cover, and align the mark on the crankshaft timing gear with the mark on the front cover; 2. Install the timing belt in sequence onto the crankshaft timing gear, water pump pulley, idler pulley, camshaft timing gear, and tensioner pulley; 3. Loosen the tensioner pulley mounting bolt by a quarter to half a turn, compress the automatic tensioner pushrod to the lowest position, insert a steel pin into the hole, adjust the pulley with a snap ring pliers, rotate counterclockwise to align the two adjustment holes of the pulley parallel to the ground, tighten the fixing screw, and remove the steel pin; 4. Rotate the crankshaft clockwise for two turns, check if the timing marks are correctly aligned, then reinstall the lower outer timing belt cover and the upper outer timing belt cover on the right side of the engine; 5. Reinstall the generator and air conditioning compressor belts, start the engine, and check for any abnormalities.
14
3
Share

Where is the handbrake on a Mercedes-Benz?

Mercedes-Benz handbrake is located on the left side of the steering column, with a button marked with the letter P. The Mercedes-Benz C-Class features an electronic parking brake that doesn't require manual operation; it automatically engages when the engine is turned off and the door is closed, tightening the handbrake. For manual operation, there's a button marked with the letter P below the left side of the steering wheel—press it to engage the handbrake and pull it to release. The parking brake, also known as the handbrake or the parking gear in automatic transmissions, provides resistance to prevent the car from rolling when parked. It locks the drive shaft or rear wheels. The parking brake applies much less force than the service brake, just enough to prevent the car from rolling on a slope.
18
3
Share

What are the letter assignments for license plates in Jilin?

Jilin license plate letter assignments are as follows: Ji A is Changchun City, Ji B is Jilin City, Ji C is Siping City, Ji D is Liaoyuan City, Ji E is Tonghua City, Ji F is Baishan City, Ji G is Baicheng City, Ji H is Yanbian Korean Autonomous Prefecture, Ji J is Songyuan City. Jilin Province, abbreviated as Ji, is a provincial-level administrative region of the People's Republic of China, with Changchun as its capital. Jilin Province is located in the central part of Northeast China, bordering Liaoning, Inner Mongolia, and Heilongjiang, and also shares borders with Russia and North Korea, situated at the geographical center of Northeast Asia. Jilin stretches 769.62 kilometers from east to west and 606.57 kilometers from north to south, covering a land area of 187,400 square kilometers, accounting for 2% of the country's total area.
12
4
Share

What is the difference between tire pressures of 2.4 and 2.5?

Tire pressures of 2.4 and 2.5 are essentially not much different. The normal tire pressure for a car is between 2.3 and 2.5 bar, and typically, tire pressure values within this range are the safest. When tires come into contact with the ground, they experience some wear, and since the degree of wear varies for each tire, the tire pressure values for each tire will also differ. Generally, the front tires of a car have higher pressure than the rear tires because the front of the vehicle houses the engine, making the front part heavier and thus requiring slightly higher tire pressure in the front wheels. Car owners only need to ensure that the tire pressures for both front wheels are the same and that the pressures for both rear wheels are consistent; it is not necessary for all four wheels to have identical tire pressures.
14
2
Share

Is the Mercedes-Benz Logo Silver?

The Mercedes-Benz logo is not silver. The dimensions of the 2020 Mercedes-Benz V250 LWB are 5370mm in length, 1928mm in width, and 2012mm in height. It is powered by a 2.0T engine with a maximum power output of 211 horsepower, paired with a 7-speed transmission. The 2020 Mercedes-Benz V250 LWB features electric side windows and a separately operable electric rear tailgate. It is equipped with a Philips TV, electric foot pedals, and adjustable color-changing ceiling lights. The vehicle boasts a Baroque-style design with a front-to-rear transparent layout. The exterior of the 2020 Mercedes-Benz V250 continues the design concept of the new V-Class, featuring a distinctive bullet-shaped front end and straight body lines, maintaining the overall styling of the V-Class.
10
0
Share

Does keeping autohold on all the time affect the car?

Keeping autohold on all the time does not affect the car. Autohold is an automatic parking function designed for encountering slopes while driving, equivalent to automatically pulling the handbrake. The autohold function is not triggered during driving; it only activates when the car is stopped. To release the stationary state, simply lightly press the accelerator to disengage the brake. Therefore, autohold has no significant impact on the braking system and can be kept on continuously. The application of autohold technology allows drivers to avoid unnecessary vehicle sliding without the need for prolonged braking or activating the electronic parking brake. When the driving force exceeds the driving resistance, autohold automatically releases the parking brake, enabling the car to start smoothly and significantly reducing the time wasted on judgment based on experience.
14
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.