How to Remove the Wiper Blades on a Tiida?

What is the sequence for walking around the vehicle in Subject 3?

In Subject 3, the walk-around the vehicle is performed counterclockwise. Additional information about the Subject 3 test: Preparations before starting the vehicle in Subject 3: First, walk around the vehicle to observe the rear road conditions and check under the vehicle, then press the sensor buttons on the vehicle in sequence. After that, open the door, adjust the seat and rearview mirror angles, and fasten the seat belt. Remember to reset the dashboard, lights, gear, and handbrake to neutral before starting the test. Subject 3 test content: Subject 3 consists of 16 items: light simulation, vehicle preparation, starting, straight-line driving, lane changing, passing through intersections, passing through crosswalks, passing through school zones, passing through bus stops, meeting vehicles, overtaking, making a U-turn, gear shifting operations, left turns at intersections, right turns at intersections, and pulling over. Among these, straight-line driving, gear shifting, and pulling over have higher failure rates, while the others are basic operations.

5

4

Share

Do you need to manually turn off the turn signal when making a right-angle turn?

You do not need to manually turn off the turn signal when making a right-angle turn. If it turns off automatically, quickly turn it back on. The solution for the turn signal automatically turning off during a right-angle turn is as follows: After straightening the car body, while holding the steering wheel with your left hand, your left middle or ring finger should keep pressing the left turn signal. When preparing to turn off the turn signal, turn the steering wheel one full turn to the left, then quickly straighten it. At this point, the turn signal will automatically turn off, and you don't have to worry about accidentally switching to the right turn signal. To avoid common errors when turning off the turn signal, when about to turn it off, turn the steering wheel 90 degrees to the left, then quickly straighten it. At this point, the turn signal will automatically reset, preventing any incorrect switching. Before the turn, keep the speed low in a low gear, and straightening the car body is key. Use second gear at low speed and stay close to the outside, remembering not to cross the line. When the front of the car approaches the turning point, turn the steering wheel quickly without delay. First check if the path ahead is clear, then proceed slowly with caution. Watch the rear wheels in the rearview mirror, and remember to turn the steering wheel back.

1

2

Share

How to Check the Date of Headlights?

The date of the headlights can be checked on the stamp of the headlights. Here is the relevant introduction about car headlights: 1. Disadvantages of replacing halogen bulbs with xenon bulbs: On one hand, since the size and dimensions of xenon bulbs are different from those of the original halogen bulbs, the light-emitting part will inevitably deviate from the focal position, leading to serious negative effects such as un-focused light and incorrect high-beam function. This may even increase the chance of dazzling oncoming vehicles by hundreds of times. 2. Using a car headlight enhancer: The car headlight enhancer uses a scientific voltage-boosting method to provide a constant optimal working voltage for the car headlights. It preheats the bulb filament for protection during startup (3~6 seconds), and after startup, the headlights emit a constant, bright white light that does not vary with engine speed. It does not alter the original headlight light distribution, does not increase the load on the original car circuit, is safe and practical, and the installation method is extremely simple.

2

5

Share

Why Is There Abnormal Noise When Accelerating with the Air Conditioning On?

There are several reasons for abnormal noise when accelerating with the air conditioning on: 1. Belt Tension: The air conditioning belt may not be tight enough, causing it to slip. When you press the accelerator, the slipping belt produces abnormal noise. You can check the belt tension. 2. Voltage and Dirt: The electromagnetic clutch inside the compressor may slip due to insufficient circuit voltage or surface dirt and sludge. 3. Compressor Damage or Malfunction: The car's air conditioning compressor is the heart of the entire system. If the compressor has issues, it can cause corresponding faults. 4. Bearing Failure: A faulty tension bearing on the compressor's drive belt can also produce abnormal noise.

6

5

Share

What is the 0-100 km/h acceleration time of the Levin 1.2T?

According to official data, the Toyota Levin Hybrid 1.2T has a 0-100 km/h acceleration time of 10.37 seconds. Factors affecting a vehicle's 0-100 km/h acceleration time are as follows: Torque: Torque, in layman's terms, represents how much force is available. The greater the torque, the stronger the force pushing the vehicle, resulting naturally in faster acceleration. The Audi R8 has a maximum torque of 570 Nm and a 0-100 km/h acceleration time of 3.1 seconds. The Levin Hybrid has a torque of 185 Nm and a 0-100 km/h acceleration time of 10.37 seconds. Transmission efficiency: The transmission serves as the medium for power delivery, inevitably involving power loss. The higher the transmission efficiency, the better the acceleration performance. Generally, transmission efficiency ranks as follows: manual transmission > dry dual-clutch transmission > wet dual-clutch transmission > AT transmission > CVT transmission. The Levin Hybrid is equipped with a CVT transmission. Power-to-weight ratio: The relationship between horsepower and vehicle weight is referred to as the power-to-weight ratio (unit: Hp/T). The higher the power-to-weight ratio, the faster the acceleration. The Audi R8 has a power-to-weight ratio of 373 Hp/T and a 0-100 km/h acceleration time of 3.1 seconds. The Levin Hybrid has a power-to-weight ratio of 92 Hp/T and a 0-100 km/h acceleration time of 10.37 seconds.

5

0

Share

What is the maintenance interval for the BYD Qin Pro DM?

BYD Qin Pro-DM's first maintenance is required at 3,500 kilometers of HEV mileage, with a maintenance interval of every 5,000 kilometers. The maintenance cycle is based on HEV mileage, requiring maintenance every 5,000 kilometers, though the total mileage will exceed this. The manufacturer offers a promotional policy that includes one free maintenance service. The free maintenance covers an oil change, oil filter replacement, and a full vehicle inspection. Below is relevant information: 1. Specific regulations: Full synthetic oil can last 10,000 kilometers or one year, semi-synthetic oil can last 7,500 kilometers or nine months, and mineral oil can last 5,000 kilometers or six months. The Qin Pro's three-guarantee period is valid for 2 years or 50,000 kilometers, and the warranty period is 3 years or 100,000 kilometers. 2. BYD Qin: The BYD Qin is a high-performance sedan independently developed by BYD Co., Ltd., featuring the second-generation DM technology (capable of switching between pure electric and hybrid modes).

8

1

Share

How to Remove the Wiper Blades on a Tiida?

What is the sequence for walking around the vehicle in Subject 3?

Do you need to manually turn off the turn signal when making a right-angle turn?

How to Check the Date of Headlights?

Why Is There Abnormal Noise When Accelerating with the Air Conditioning On?

What is the 0-100 km/h acceleration time of the Levin 1.2T?

What is the maintenance interval for the BYD Qin Pro DM?

What are the new regulations for vehicle scrappage?

Why Does the Car Belt Squeak?

Can an expired forklift license still be reviewed?

Will traffic police stop you for replacing halogen bulbs with LED bulbs?