How to Remove the Wiper Blade Rubber Strip?

[PaisleyAnn]

The method to remove the car wiper blade rubber strip is: Remove the caps on both sides of the wiper blade, pull out the old wiper blade rubber strip, thread the new rubber strip through the two steel strips, and then restore the caps. The function of the wiper blade is: To remove raindrops, debris, and dust attached to the vehicle's windshield, improving the driver's visibility and enhancing driving safety. The steps to replace the car wiper blade are: 1. Lift the wiper blade upright; 2. Press the clip below to remove the wiper blade rubber strip; 3. Take off the wiper blade; 4. Pry up the front end of the middle clip; 5. Insert the wiper blade into the middle clip, pull it tight by hand until you hear a click sound, indicating the replacement is complete.

[Hunger]

I enjoy doing DIY car maintenance, and replacing wiper blades is a piece of cake. First, lift the wiper arm and place a thick towel on the windshield to prevent it from snapping back and damaging the glass. Then, carefully observe the clip structure at both ends of the wiper blade—there’s usually a small plastic cover or metal clip that can be pried open with a fingernail or a small screwdriver to release the fixed end. Next, slowly pull out the old rubber strip along the track of the wiper blade frame, being mindful of any metal stiffeners inside so you don’t lose them. When installing the new rubber strip, align it with the track groove first, reinsert the metal stiffener, and then slowly push it in from one end until it reaches the end, finally securing the clip. The whole process takes about ten minutes, saving you a trip to the repair shop.

[CadenFitz]

Last time my car's wiper blades weren't cleaning properly, I replaced the rubber inserts myself which was really convenient. Remember to first lift the wiper arm and place a cloth between the glass and the wiper arm to protect the windshield. Locate the small clips at both ends of the wiper blade - if you can't open them with your fingernail, use a coin to pry them. When removing the rubber insert, be careful as there's a slender metal support strip inside; hold it down with your hand when pulling out the old insert to prevent it from flying out. When installing the new rubber insert, pay attention to the orientation - usually the side with grooves should face the skeleton track when pushing it in. The key is to handle everything gently throughout the process as the skeleton can deform with just a little force. Finally, remember to test the wiping performance - if it's not clean, the insert isn't properly installed.

[Prim]

Replacing wiper blades isn't actually troublesome, even someone as clumsy as me can manage it. The preparation involves just two steps: lift the wiper arm and place a towel underneath, then locate the buckle structures at both ends of the wiper blade. When removing, press the buckle and pull the blade outward, making sure to keep the metal strip inside the old blade safe. The biggest fear when installing a new blade is putting it in the wrong direction—pay attention to the shape of the guide rail on the side of the blade and align it with the groove of the frame before sliding it in. Avoid using excessive force during the process, as deforming the frame will render it useless. Finally, secure the buckles at both ends and test the wiping performance. The whole process requires no professional tools.

[McAlan]

Decades of driving experience have taught me that replacing wiper blades requires attention to safety details. The first step is to secure the wiper arm and cover the glass with a towel to prevent collisions. The clips are usually located at both ends of the wiper blade, and can be pried open with a coin or car key. When removing the rubber blade, the metal pressure strip will come out with it—don’t lose this piece. The key to installing a new blade is aligning it with the track, placing the metal strip back into the groove, and then sliding it into the frame. After resetting the clips, make sure they are secure; otherwise, the blade may fall off while driving. Replacing the rubber blade every six months is much cheaper than replacing the entire wiper, and it ensures safer driving in the rain.

[RosalieMarie]

Last time during heavy rain, I noticed the wipers weren't cleaning properly, so I checked some guides and learned how to replace the rubber blades. During preparation, you need to lift the wiper arms and place soft cloth on the glass to prevent scratches. After some trial and error, I found the hidden clips at both ends of the wiper blade - just pry them open with your fingernail. The biggest challenge when removing the rubber blade was that the metal strip inside tends to fall out, so you need to grip the rubber and pull it out slowly. When installing the new rubber blade, make sure to align it with the track direction correctly - insert one end first and then push it through. The pushing process requires some effort, but don't use brute force. Finally, secure both end clips, test the wiping effect with water spray, and ensure the rubber fully contacts the glass surface.