How to Remove the Steering Wheel of Changan Eado?

[VanAriel]

To remove the steering wheel of Changan Eado, the first step is to disconnect the battery. The specific steps are as follows: 1. Detailed operation for removing the steering wheel of Changan Eado: After disconnecting the battery, turn the steering wheel approximately 90 degrees. Insert a screwdriver from the front into the hole behind the steering wheel, positioning the head of the screwdriver between the retaining spring and the airbag hook. Apply a skillful upward force to separate the retaining spring from the hook, causing the airbag side to pop slightly towards the seat. Then, turn the steering wheel 180 degrees and repeat the process on the opposite side to release the retaining spring and remove the airbag. Disconnect the yellow safety buckle behind the airbag, then unplug the airbag connector to remove the airbag. Unplug the coupling coil socket of the airbag located above the interior of the steering wheel. Use an M12 spline to loosen the central fixing bolt of the steering wheel counterclockwise, completing the removal of the steering wheel. 2. The steering wheel is connected to the steering shaft via a spline, and its function is to convert the force applied by the driver on the edge of the steering wheel into torque, which is then transmitted to the steering shaft: Using a steering wheel with a larger diameter reduces the force required by the driver during steering. The steering transmission shaft, as a connecting component between the steering gear and the steering shaft, facilitates the standardization of the steering gear, compensates for errors during manufacturing and installation, and ensures a more rational installation of the steering gear and steering wheel in the vehicle.

[SanRyder]

When removing the steering wheel of a Changan Eado, I pay special attention to safety. First, it's absolutely crucial to disconnect the negative terminal of the battery and wait for 15 minutes to allow the system to fully discharge. This is super important because the airbag module carries current, and accidental contact could cause it to deploy and cause injury. Then, locate the hidden screw holes on both sides of the steering wheel, unscrew them with a small screwdriver, and gently remove the airbag cover. This will reveal the large central nut, which should be loosened counterclockwise with a correctly sized wrench. Finally, prepare a steering wheel puller, install it properly, and slowly tighten it to pull out the steering wheel. Throughout the process, movements should be gentle—avoid using excessive force to prevent damage to the steering column or internal wiring. After completion, check for any wear on the parts, such as oxidized contacts, and clean them if necessary. When reinstalling, align the original position marks and tighten everything securely to ensure smooth operation. This job is manageable for DIYers, but if you lack experience, it's safer to seek professional assistance.

[Adriel]

I once disassembled the Eado steering wheel at home. I was a bit nervous at first, but taking it step by step wasn't too difficult. The first step is always to disconnect the battery! Safety comes first. The airbag part was the trickiest - the Eado model usually has a small hole under the steering wheel where you can insert a pointed tool to pry open the airbag cover. Be careful when removing the airbag connector to avoid breaking the wires. After loosening the center nut, I borrowed a puller and with a few twists, it came off. The key is using proper tools - don't cut corners. When pulling out the steering wheel, support it gently with your hand to prevent damage. Remember to take photos of the wiring positions during disassembly for reference during reassembly. My advice for beginners is to spend more time studying tutorial videos before attempting this to minimize risks. After removal, it's worth checking the steering column lubrication - if it squeaks, apply some grease. Overall, it's quite worthwhile.

[LeLaila]

Removing the steering wheel isn't difficult, just remember a few steps. First, disconnect the negative terminal of the battery and wait ten minutes for the airbag to deactivate. On the Eado's steering wheel, there are screws on both sides of the airbag cover that need to be loosened. Then carefully remove the airbag assembly without touching the wires. In the center, there's a nut; after loosening it, use a specialized puller or tools to assist in twisting the steering wheel off—do it gently without forcing it. When reinstalling, align it with the original position marks, secure it firmly, and ensure it's safe.