How to Remove the Steering Wheel of a Honda Fit?

1 Answers
DelGrace
07/30/25 4:18am
Honda Fit steering wheel removal method is: 1. Adjust the steering wheel angle by rotating it 90 degrees; 2. Position the screwdriver - when the hole behind the steering wheel is facing upward, insert a flat-head screwdriver horizontally along the upper edge of the opening; 3. The screwdriver will then be above a horizontal wire, which needs to be pressed downward; 4. Gently pull the airbag outward; 5. Repeat the same process on the other side to complete the steering wheel removal. The Fit is equipped with a 1.5L naturally aspirated engine, delivering a maximum power of 96kW and maximum torque of 155Nm, paired with a CVT transmission.
Was this review help?
8
5
Share
More Forum Discussions

Why Does a Motorcycle Get Louder the More You Ride It?

Motorcycles get louder due to foreign objects or an increase in the vehicle's own faults. Below is an introduction to the reasons why a motorcycle's sound becomes increasingly louder: 1. Causes of the noise: Noise is generally produced by vibration, collision, or friction of objects. If a motorcycle's engine is working normally, the sound during operation is minimal and harmonious. However, when the engine malfunctions, abnormal noises occur. 2. Common faults causing noise in scooters: (1) Loose timing camshaft bearings. (2) Severe wear on the working surfaces of the timing cam and valve rocker arm. (3) Broken rear clutch spring. (4) Improper belt selection or clutch acceleration lag, resulting in the sound of the belt hitting the casing. (5) Severe wear of the front clutch pulley weights. (6) Wear of the electric starter clutch (the abnormal noise is more pronounced during electric starting). (7) Incorrect ignition timing, causing the sound of valves hitting the piston (commonly seen in vehicles after maintenance).
16
0
Share

How to Determine the Tonnage of a Light Truck Rear Axle?

The method to determine the tonnage of a light truck rear axle is to check the model number on the vehicle's nameplate. Generally, the middle two digits on a truck's nameplate indicate the vehicle's gross weight, which is the combined weight of the vehicle's own weight and the permitted load capacity. For example, '09' indicates a gross weight of 9 tons. (The fourth digit represents the sequence of different vehicle models of the same tonnage from the same manufacturer.) The gross weight is the sum of the load-bearing capacity of the front and rear axles, with the front axle typically bearing about half the load of the rear axle. The rear axle mainly has two technical parameters: 1. Load capacity level; 2. Gear ratio: There is no unified format for the numbering regulations of rear axles among manufacturers, so the focus should be on these two parameters provided. The load capacity level indicates the maximum design load-bearing capacity of the rear axle, expressed in tons, such as: 6-ton level, 10-ton level, 11-ton level, etc.
14
2
Share

How to Choose the Correct Lane as a Beginner Driver?

On a one-way single-lane road, there's no choice but to follow the traffic flow. For two-lane one-way national highways and urban roads, prioritize using the left lane. If it's a large road with three or more one-way lanes, it's advisable to stay in the middle lane—not only does this avoid criticism from faster drivers, but it also minimizes interference from pedestrians and bicycles. Additionally, the middle lane offers better visibility and easier lane changes. Here are some extended tips for beginners: Maintain a safe distance from the vehicle ahead. Whether on busy or lightly trafficked roads, always keep a proper following distance. This distance should be determined by your current speed: at around 40 km/h, maintain at least 30 meters; at 60 km/h, no less than 50 meters. In rainy or wet conditions, the distance should match the absolute value of your speed—for example, at 40 km/h, keep at least 40 meters apart, and so on.
1
5
Share

What causes a Chevrolet to suddenly fail to start?

The reasons why a Chevrolet suddenly fails to start are as follows: 1. Battery depletion: When the car battery is dead, the car will definitely not start. Battery depletion can be caused by lack of water in the battery, battery failure, prolonged use of the air conditioning, and other reasons. 2. Ignition system failure: The ignition system provides high voltage to the spark plugs to ensure the normal operation of the car. If the car's ignition system fails, the car may not start. Poor connections in the low-voltage circuit or leakage in the high-voltage wires can cause ignition system failure. 3. Severe engine carbon buildup: Severe carbon buildup in the car engine can prevent the car from starting. Factors such as excessive water in gasoline, poor fuel quality, and poor sealing of the valve seat rings can lead to carbon buildup. It is important to regularly clean the engine carbon buildup and use higher-quality gasoline. 4. Starter aging: An aging car starter can also cause weak starting or failure to start. Therefore, it is necessary to replace the car starter regularly and avoid using it for too long.
5
2
Share

Are there any dangers in selling points from a driver's license?

Selling points from a motor vehicle driver's license is an act that obstructs official duties and violates the Administrative Penalty Law. When handling traffic violation or illegal business for motor vehicles, the person must match the document, and it is not allowed for one person to handle violations or illegal activities for multiple motor vehicles. Relevant information about the driver's license is as follows: 1. Introduction: The People's Republic of China Motor Vehicle Driver's License, referred to as the driver's license or 'driver's permit,' is a license that must be applied for by motor vehicle drivers in accordance with the laws of the People's Republic of China. 2. Examination Content: The test subjects include traffic regulations and related knowledge, field driving, and road driving (including safe and civilized driving), totaling three items.
3
0
Share

Can You Use 3rd Gear for Turns in Subject 3?

You can use 3rd gear for turns in Subject 3, but the speed should not be too fast, preferably around 20 km/h. Here is a brief introduction about Subject 3: 1. Basic Information: Subject 3, which includes the road driving skills test and the safety and civilized driving knowledge test, is part of the motor vehicle driver's license assessment. It is the abbreviation for the road driving skills and safety and civilized driving knowledge test in the motor vehicle driver's examination. The content of the road driving skills test varies for different types of vehicles. 2. Test Content: The road driving skills test for Subject 3 generally includes: preparation before driving, simulated lighting test, starting, driving straight, gear shifting operations, changing lanes, pulling over, going straight through intersections, turning left at intersections, turning right at intersections, passing pedestrian crossings, passing school zones, passing bus stops, meeting oncoming vehicles, overtaking, making U-turns, and night driving.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.