How to Remove the Spare Tire of the Outlander?

How to reset the tire pressure monitoring system on a Mercedes-Benz R400?

After the tire pressure indicator light comes on, you must ensure the vehicle is parked safely by the roadside and first check the tire pressure monitoring function on the navigation screen for any wheel abnormalities. If the alarm is triggered due to excessively high tire pressure, we can slightly increase the tire pressure to reach the safe value. If the display shows excessively low tire pressure, you need to reset the system and drive the car for a while. The tire pressure warning will then be eliminated, resolving the issue.

1

3

Share

What to Do When the Truck Rolls After Applying the Handbrake?

If the truck continues to roll, it indicates that the handbrake is not tightened properly or there is an issue with the handbrake. This usually means the handbrake cable is faulty, often due to misalignment or deformation of the handbrake shoe bracket. If you forget to apply the handbrake when parking normally and the vehicle starts to roll backward, pressing the foot brake firmly may prevent significant danger. Whenever the vehicle is stuck on a slope and starts to roll backward, the first thing the driver should do is stay calm and avoid panic, then quickly press the foot brake.

7

0

Share

What to Do When the Brake Malfunction Light Comes On?

The solutions for when the brake malfunction light comes on are: 1. Check for poor contact or damage in the wiring and connectors; 2. Inspect the installation gap, positioning, and contamination of the wheel speed sensor and toothed ring; 3. Avoid high-speed driving and sudden braking; 4. Adjust the wheel bearing clearance to the normal value. The reasons for the brake malfunction light coming on are: 1. When the vehicle speed exceeds 10 km/h, the speed signal is not transmitted to the ABS control unit; 2. When the vehicle speed exceeds 40 km/h, the speed signal exceeds the tolerance value; 3. There is a recognizable open circuit or short circuit to the positive or ground in the sensor.

6

0

Share

How to Conduct Annual Inspection for New Vehicles?

The owner of a motor vehicle may apply for the inspection compliance mark at the vehicle registration authority up to three months before the expiration of the current inspection validity period. When applying, the vehicle owner should fill out the application form and submit the vehicle registration certificate and the compulsory traffic accident liability insurance certificate. The vehicle registration authority shall, within one day from the date of acceptance, verify the motor vehicle, review the submitted documents and certificates, and issue the inspection compliance mark. For small non-commercial passenger vehicles with 6 seats or fewer within 6 years of registration, an exemption from on-site inspection is implemented. Owners can directly apply for the inspection compliance mark at the traffic police department or vehicle registration authority.

10

1

Share

What does mass production of cars mean?

Mass production of cars refers to small-scale production. Here are the relevant details: 1. Limited production: For example, some special models have a small market demand and are produced in limited quantities for specific consumer groups. 2. Reasons: New models launched in the market may start with small-scale production due to capacity constraints. For instance, producing a supercar involves small demand, most processes requiring manual labor, long production cycles, and special materials, hence only small-scale production is feasible. Alternatively, newly introduced models may initially have low automation levels, uneven employee skills, low production efficiency, and limited capacity, thus starting with small-scale production. However, once processes and employee skills improve, large-scale production can begin.

6

1

Share

How to Replace the Battery in a Buick Remote?

Turn the car remote key to the back, and you can see that the back cover is divided into two parts. On the side where the key ring is visible, the battery is located under the back cover. First, insert a flat-head screwdriver into the gap and gently push upwards to partially open the back cover. Then, move the screwdriver along the gap towards both sides. Use your hand to move the back cover in the closing direction, and you can remove the back cover to see the inside of the battery. A protruding clip can be seen on one side of the battery.

13

3

Share

How to Remove the Spare Tire of the Outlander?

How to reset the tire pressure monitoring system on a Mercedes-Benz R400?

What to Do When the Truck Rolls After Applying the Handbrake?

What to Do When the Brake Malfunction Light Comes On?

How to Conduct Annual Inspection for New Vehicles?

What does mass production of cars mean?

How to Replace the Battery in a Buick Remote?

How to Activate the Auto Hold Function in Mercedes-Benz E-Class?

What does Volkswagen CleanAir mean?

How to Turn Off the Auto Start-Stop Function in Mercedes-Benz C-Class?

What is the basic introduction to car tire knowledge?