How to remove the seats of Buick GL8?

1 Answers
WestonDella
07/29/25 3:37pm
Buick GL8's seat removal method is: 1. Pull the handle near the window of the rear seat; 2. Fold the backrest of the rear seat forward, and push the cushion part backward; 3. Lift it upward. The Buick GL8 is a 5-door, 7-seat MPV with body dimensions of: length 5238mm, width 1878mm, height 1776mm, and a wheelbase of 3088mm. The Buick GL8 is equipped with a 2.0T turbocharged engine and a 9-speed automatic transmission, with a maximum power of 174 kW and a maximum torque of 350 Nm. Its drive mode is front-wheel drive, with a front suspension using a MacPherson independent suspension and a rear suspension using a torsion beam non-independent suspension.
Was this review help?
3
3
Share
More Forum Discussions

Does an extra child in the car count as overloading?

Every vehicle will indicate its load capacity or passenger capacity. According to the rules of the "Road Traffic Safety Law of the People's Republic of China", overloading is calculated by headcount. As long as the number of people exceeds the limit, even if it's a child or a baby held in arms, it is considered overloading. The following are the relevant penalties for being found overloading: According to traffic regulations, for passenger vehicles other than buses and school buses, carrying passengers exceeding the approved number by less than 20% will result in a fine of 100 yuan and 3 demerit points, while exceeding the approved number by more than 20% will result in a fine of 100 yuan and 6 demerit points. For a family five-seat car, carrying one extra person is a 20% overload, which is a violation. If caught by traffic police on the highway, it will result in 6 demerit points and a fine of 200 yuan.
20
0
Share

Is Full-Range Speed Detection Really Full-Range?

The so-called "full-range" means that on a relatively long road section, there are speed monitoring devices at every location without any omissions. Here is some relevant information about vehicle speed detection: 1. Speed detection methods: (1) Loop detection: This is a classic method with good detection results. It is commonly used in southern regions such as Shanghai and Guangdong. The system determines whether a vehicle is speeding based on its speed when passing parallel loops and captures photographic evidence. (2) Video detection: This method analyzes continuous video images to track the behavior of violating vehicles and controls the camera to capture violations. The advantage of this system is that it is not limited by road conditions, does not require road destruction for installation, or the embedding of induction loops underground. Instead, it detects traffic data by setting up cameras above the road, making it a new-generation road vehicle detection method. 2. Precautions: Cameras at intersections can also capture violations, including not only running red lights and speeding but also illegal lane changes on solid lines and crossing lines. The capture efficiency during the day can reach over 95%, and at night, it is still around 90% due to night vision capabilities.
20
4
Share

Is there a difference in fuel consumption when the car air conditioner is set to maximum versus minimum?

There is a difference in fuel consumption when the car air conditioner is set to maximum versus minimum. Below is a related introduction to car air conditioners: 1. Air conditioner layout: Different types of air conditioning systems have varying layout methods. Currently, the most widely used in passenger cars is the integrated heating and cooling air conditioning system. Its layout involves assembling components such as the evaporator, heater radiator, centrifugal blower, and control mechanism together, collectively referred to as the air conditioner assembly. 2. Air conditioner composition: Modern air conditioning systems consist of a refrigeration system, heating system, ventilation and air purification devices, and a control system. A car air conditioner generally includes components such as the compressor, electronically controlled clutch, condenser, evaporator, expansion valve, receiver-drier, piping, condenser fan, vacuum solenoid valve, idle speed controller, and control system. The car air conditioning system is divided into high-pressure and low-pressure lines. The high-pressure side includes the compressor output side, high-pressure lines, condenser, receiver-drier, and liquid lines; the low-pressure side includes the evaporator, accumulator, suction line, compressor input side, and compressor oil sump.
18
1
Share

Can the Accord use 95 octane gasoline?

According to the official vehicle manual recommendation, the Accord should use 92 octane gasoline. In addition to checking the appropriate gasoline grade in the vehicle manual, the Accord's fuel cap also indicates the recommended octane rating. Generally, the fuel grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. However, with the application of new technologies, the fuel grade cannot be solely determined by the compression ratio. High compression ratio engines can also be tuned to use lower octane gasoline because, apart from the compression ratio, other factors such as ignition timing, turbocharging technology, and Atkinson cycle technology also play a role. Generally, the higher the gasoline octane rating, the higher the octane value and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If the Accord occasionally uses the wrong gasoline grade, simply switch back to the correct grade after consumption. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower octane gasoline, using higher octane gasoline will not cause damage, but the increase in octane value will alter the fuel's ignition point, leading to delayed combustion in the engine. This results in reduced engine power and thermal efficiency, with the actual feedback being poorer performance. For vehicles recommended to use higher octane gasoline, using lower octane gasoline can cause engine knocking. Due to the significantly lower octane value, the gasoline's ignition point decreases, causing premature ignition during the compression stroke. If combustion occurs before the spark plug ignites during the compression stroke, resistance will arise during the upward stroke. This resistance makes the engine run very unstably. If the knocking is imperceptible, it only increases noise without obvious engine damage. However, noticeable knocking indicates severe engine conditions, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, and in severe cases, cylinder scoring.
15
1
Share

How to reset the maintenance light on Dongfeng Honda?

Dongfeng Honda maintenance light reset method: 1. Turn the vehicle ignition switch to ON mode. 2. Repeatedly press the SEL/RESET button until "Maintenance" appears on the display, then press the Enter button. The engine oil monitor information will then appear on the screen. 3. Hold the Enter button for about 10 seconds, and the maintenance light will be reset. Here is some relevant information: 1. The wrench symbol displayed on the car dashboard is set by the manufacturer to remind the owner to perform maintenance at regular intervals according to mileage. This means when this light stays on for a long time, you should go to a 4S shop for maintenance. Different vehicle models from different companies have different maintenance intervals, which should be based on the vehicle's user manual. 2. After maintenance is completed, there is a reset procedure to zero the maintenance light. If not reset, the indicator light will remain on even after maintenance is performed. 3. The vehicle's maintenance cycle is preset when the car leaves the factory, so the "small wrench" symbol will appear at certain mileage intervals to remind the driver to perform timely maintenance. Typically, our car maintenance cycle is every 5,000–8,000 kilometers, while the factory-set cycle is generally longer than 8,000 kilometers.
13
0
Share

Is a Commercial Vehicle Still Considered Commercial After Transfer?

Whether the operating permit of a commercial vehicle is transferred or canceled after sale depends on the intended use by the buyer. There are two scenarios: Converted to a Private Vehicle: The vehicle will still be subject to the 8-year scrappage period for commercial vehicles. After conversion, compulsory traffic insurance is required, and an annual inspection is mandatory. The first step is to obtain a certificate from the transportation authority, then change the vehicle's usage type at the vehicle management office, followed by canceling the operating permit at the transportation authority. Once canceled, the vehicle can no longer be used for commercial purposes. The annual inspection of the driving license will proceed under normal procedures, and the scrappage period remains unchanged. Important Notes: When a vehicle is transferred from one city to another, changing its registration to a different vehicle management authority is referred to as a transfer of registration. This process requires changing the license plate and driving license and involves procedures at both the original and new vehicle management authorities, including transfer-out and transfer-in procedures. Basic Process: File check at the vehicle management office, criminal investigation, business verification, receiving the driving license acceptance receipt, obtaining the original driving license, transfer of purchase tax, and insurance renaming. Completing the transfer of a used vehicle legally ensures the transfer of ownership and guarantees the legality of the vehicle's origin, such as avoiding purchasing smuggled or stolen vehicles. It also clarifies the division of responsibilities between the buyer and seller regarding the vehicle, such as debt disputes and traffic violations, protecting the legal rights of both parties. Requirements include a legal source and documentation, no outstanding bank liens or court seizure records, no unresolved traffic violations or accident records, no outstanding fee arrears, and all necessary documents must be complete. Continuing Commercial Use: The operating permit should be transferred because the commercial vehicle's ownership changes upon sale, necessitating the transfer of the operating permit.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.