How to remove the rear wiper of Trumpchi GS4?
4 Answers
Here is the method to remove the rear wiper of Trumpchi GS4: 1. Lift the wiper arm upwards and place a towel on the windshield corresponding to the middle position of the wiper; 2. Rotate the wiper and the wiper arm to form a 90-degree angle, and look for the small hidden buckle at the angle position between the wiper and the wiper arm; 3. Press the small hidden buckle without releasing it, and use the other hand to pull the entire wiper downward, towards the root of the wiper arm; 4. When the hook is exposed during the downward movement of the wiper, remove the wiper from the side to complete the removal. Additional information: The wiper, also known as a windscreen wiper, water wiper, or windshield wiper, is a device used to wipe off raindrops and dust attached to the vehicle's windshield to improve the driver's visibility and enhance driving safety.
Removing the rear wiper of the Trumpchi GS4 is actually quite simple, but it needs to be done step by step. First, make sure the car is turned off and the handbrake is engaged—safety first. Use a flat-head screwdriver to gently pry open the plastic cover at the end of the wiper arm, exposing the screw or clip underneath. Since I use my car frequently, I remember this model usually has an 8mm nut. Use an appropriate wrench or socket to slowly loosen it, but don't remove it completely to avoid dropping the tool and damaging the glass. Then, gently push the base of the wiper arm upward with your hand. There will be some resistance, so be patient and avoid using excessive force. Once the nut is loose, you can carefully lift the entire wiper arm away from the glass. If it's stuck, you can wiggle it slightly or lubricate the joint for easier removal. After removal, it's a good idea to check if the wiper blade is worn and replace it in time to avoid poor visibility during rainy days. The whole process takes less than ten minutes, but make sure you have all the necessary tools, such as a screwdriver and wrench. If it's your first time doing this, refer to the owner's manual to avoid damaging the joint, as rear wiper parts can be hard to find. Safe driving starts with maintaining these small details, and regular upkeep saves a lot of hassle.
As a beginner in car repair, I find removing the rear wiper isn't difficult, the key is to be careful not to damage anything. First, park the car securely and turn off the engine, find a quiet place to work. Feel the end of the wiper arm with your hand, there's a small cover there, gently pry it open to reveal the screw. Use a wrench to loosen the screw counterclockwise, don't use too much force or it might strip. Then slowly lift the arm, if it feels stuck, wiggle it left and right to loosen it. Last time I removed it, I found it was rusted, spraying some lubricant made it much easier. For tools, a basic screwdriver and small wrench are enough, avoid using brute force to prevent scratching the glass or wiper arm. After removal, you can clean the mounting point and check for any cracks. The design of this car's rear wiper is quite user-friendly, generally not prone to mistakes. But if you're unsure, ask a knowledgeable friend to check or go to a repair shop for convenience. The main point is to operate gently, it's safer to do the whole process in dry weather, never work in the rain.
To remove the rear wiper of the Trumpchi GS4, it mainly takes three steps. First, close the hood or trunk to ensure safety. Then locate the small cover at the end of the rear wiper arm and pry it open with a screwdriver to expose the screw inside. Rotate the screw counterclockwise to loosen it, and slowly lift the wiper arm by hand. If it's stuck, gently wiggle it a few times or apply some lubricant. The tools required are simple—just a household screwdriver. After removal, immediately store it properly to avoid losing it. Be careful not to let the wiper arm snap back and injure anyone or damage the glass. Once done, installing a new one becomes easy.
