How to Remove the Rear Seats of the Fit?

1 Answers
JosiahLee
07/29/25 1:41pm
Method for removing the rear seats of the Fit: There are two screws in the middle of the rear seats. Remove these two screws, then detach two clips to take off the rear seats. The top trim Fit comes with Magic Seats, which can be folded up. The Fit is a hatchback launched by GAC Honda, with dimensions of 4065 mm in length, 1695 mm in width, and 1525 mm in height, and a wheelbase of 2530 mm. In terms of power, the Fit is equipped with a 1.5-liter naturally aspirated engine across the lineup, coded L15B3, delivering a maximum power of 96 kW, a maximum torque of 155 Nm, with the maximum power achieved at 6600 rpm and the maximum torque at 4600 rpm.
Was this review help?
7
5
Share
More Forum Discussions

What is the capacity of the Accord's windshield washer reservoir?

The Accord's windshield washer reservoir has a capacity of 4 liters. The windshield washer fluid storage is located on the rear side of the engine hood pressure strut, with the reservoir cap marked with a washer symbol. The Accord's body dimensions are: length 4858mm, width 1942mm, height 1670mm, wheelbase 2820mm, trunk volume 510L, and minimum ground clearance 203mm. The Accord is equipped with a 1.5T turbocharged engine, delivering a maximum power of 142kW at 5600rpm and a maximum torque of 243Nm between 2000-5000rpm, paired with a continuously variable transmission.
2
0
Share

Why Does the Inside of Car Windows Frost Over?

Car windows frost over on the inside due to residual heat inside the vehicle after the occupants leave, which causes the temperature of the windows to be higher than the outside temperature, leading to condensation that freezes when it comes into contact with the cold. Methods to prevent the inside of the car windshield from frosting over include: 1. Parking the vehicle in a garage; 2. Covering the car with a car cover or using a large cloth to cover the windshield; 3. Spraying antifreeze on the windshield before parking. Methods to remove ice from the car windshield include: 1. Turning on the car's heater; 2. Using a hard plastic scraper to remove the ice; 3. Using a specialized de-icer; 4. Opening the car doors to ventilate after parking.
4
0
Share

How to Solve High Engine Temperature?

The solutions for high engine temperature are: 1. Check if the radiator coolant is at the normal level; 2. Inspect the radiator, cooling hoses, and all components for leaks; 3. Top up the coolant. Symptoms of high engine temperature include: 1. Decreased engine power; 2. Increased fuel consumption; 3. Accelerated wear of engine components. The causes of high engine temperature are: 1. Coolant level in the radiator is below the minimum mark; 2. Insufficient fan speed; 3. Lack of power in the coolant circulation; 4. Blocked water passages or clogged radiator; 5. Air trapped in the cooling system; 6. Thermostat failure.
17
3
Share

What is the tire model of the Benben mini?

The tire model of the Benben mini is 155/65r13. 155 represents the tire section width of 155 millimeters, 65 represents the tire aspect ratio of 65, which is the percentage of the tire section height divided by the tire width. R stands for radial tire, and 13 represents the rim diameter of 13 inches. Tires are an important component of a car, being the only part that comes into contact with the ground. Tires are crucial for the driving safety and stability of the vehicle. The Benben mini is a small car newly designed by Changan Automobile for its future leapfrog development. In terms of body dimensions, the Benben mini has a length, width, and height of 3520mm, 1570mm, and 1490mm respectively.
6
3
Share

How to Reset the Maintenance Light on a Citroen C-Quatre?

To reset the maintenance light on a Citroen C-Quatre, follow these steps: 1. Turn off the ignition; 2. Press and hold the maintenance mileage reset button; 3. Turn on the ignition, and the odometer will start counting down; 4. When the display shows '0' and the maintenance light turns off, the process is complete. The Citroen C-Quatre has body dimensions of 4588mm in length, 1773mm in width, 1486mm in height, and a wheelbase of 2610mm. It is equipped with a 1.6L naturally aspirated engine, delivering a maximum power of 86 kW at 6000 rpm, paired with a 5-speed manual transmission.
6
5
Share

What are the symptoms of a faulty ignition wire in a car?

Here are the fault phenomena caused by a faulty ignition wire in a car: 1. Unstable engine operation or shaking: For example, reasons such as poor quality or aging of the high-voltage wire can cause this. 2. Single or multiple cylinder misfires or intermittent faults: For example, individual high-voltage wires with quality issues leading to poor conduction or resistance changes may cause this. 3. Abnormal ignition: The engine may experience weak acceleration, hesitation, or poor acceleration; For example, during use, the conductivity of the high-voltage wire weakens, internal resistance increases, resulting in reduced ignition intensity to the spark plug, weak ignition, and incomplete combustion.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.