···
Log in / Register

How to Remove the Rear Seats of a Skoda Octavia?

4 Answers
StCamille
07/28/25 9:18pm
Skoda Octavia rear seat removal method: On both sides of the headrest area near the windows, there are pull handles. Pulling these handles allows the rear seat backrest to fold forward. For the seat cushion part of the rear seats, in most cases, you simply need to push the cushion firmly toward the rear of the car and then lift it upward to remove it. The Octavia is a compact sedan under SAIC Volkswagen Skoda, featuring a MacPherson strut front suspension and a torsion beam rear suspension. In terms of body dimensions, it measures 4675mm in length, 1814mm in width, and 1460mm in height, with a wheelbase of 2686mm. Power is provided by a 1.2T turbocharged engine, paired with a 7-speed dual-clutch transmission.
Was this review help?
16
1
Share
Fonseca
08/12/25 12:55am
The rear seats of my Skoda Octavia aren't too difficult to remove. I've done it myself before to make more space for luggage during family trips. The basic steps start with the seat cushion—feel for a handle or clip at the bottom front edge, give it a gentle pull, and the cushion lifts right off. Next, tackle the backrest: first lay it flat, then locate a small button or lever in the trunk or side to release the anchor points. The whole process takes about 20 minutes. Just be careful not to use excessive force to avoid damaging plastic parts or snagging seatbelts. Once removed, the extra space is significant—perfect for more camping gear. I also took the chance to clean dust under the seats, saving a trip to the repair shop. If you're unfamiliar, it's best to have a helper or check the owner's manual to ensure each step is done safely. This kind of DIY is both cost-effective and practical for everyday needs.
Was this review help?
2
0
Share
Expand All
VanKaleb
10/01/25 2:05am
As someone who loves tinkering with cars, removing the rear seats of a Skoda Octavia is a piece of cake for me. You'll need basic tools, and a flat-head screwdriver is sufficient. Start the removal from the seat cushion—there's a hidden pull ring at the front edge of the seat, and a simple tug will release it entirely. Then, for the backrest, fold it down and locate the securing screws or clips on the side; loosen them to detach it. Handle everything gently to avoid damaging the wiring, especially if the seats have heating functions—remember to disconnect the power first. Once done, the trunk instantly becomes more spacious, perfect for loading bikes or boxes, making my cargo tasks much easier. However, be sure to test the stability after reinstallation to prevent any dangerous wobbling. This kind of operation isn't complicated, and there are plenty of online tutorials—doing it yourself feels really rewarding.
Was this review help?
19
4
Share
Expand All
StGage
11/14/25 3:53am
If you've just got your hands on an Octavia and want to remove the rear seats, the method is quite simple. First, check the front underside of the seat cushion for a small hook, give it a pull by hand, and the cushion will come off easily. Then, recline the backrest and unlock the anchor points—usually by pushing a small lever. The whole process takes about 10 minutes; take it slow to prevent breakage. Once removed, you'll have more space to clean or store items. Beginners might worry about mistakes, so I recommend taking photos to note the positions for easier reassembly. If any issues arise, a professional shop can quickly help.
Was this review help?
2
3
Share
Expand All
More Forum Discussions

What is the purpose of car ABS?

The purpose of car ABS is to continuously switch between the critical point of tire sliding and rolling, effectively shortening the braking distance and preventing the vehicle from skidding during emergency braking. The working principle process of car ABS is: 1. The ABS system monitors the rotation speed of the four wheels. When a wheel is about to lock, the system releases the brake of that specific wheel, allowing it to resume rotation; 2. After the wheel is about to resume rotation, braking hydraulic pressure is applied to that wheel; 3. When the wheel is about to lock again, the system releases the brake of that specific wheel; 4. The system repeats the above process multiple times within one second to maximize the potential of the brakes and ensure the stability and normal operation of the vehicle.
17
5
Share

What Causes the BMW 740 to Shake During Rapid Acceleration?

Reasons for the BMW 740 shaking during rapid acceleration: Severe Engine Carbon Buildup: The most common cause of car shaking is a dirty throttle body or excessive carbon buildup in the fuel injectors. When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold start injector is largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts and making it difficult to start. In this situation, the car will only start easily once the carbon deposits have absorbed enough gasoline to reach saturation. After starting, the gasoline adsorbed on the carbon deposits is then drawn into the combustion chamber by the engine's vacuum suction, causing the air-fuel mixture to become too rich. The engine's combustible mixture alternates between being too lean and too rich, leading to idle shaking after a cold start. Ignition System Issues: Check the condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance in the ignition system or inadequate spark plug firing can also cause this type of problem. Unstable Fuel Pressure: If you have already cleaned the engine carbon deposits, throttle body, replaced the fuel gasket and spark plugs, but still notice the car shaking at idle, it is recommended to visit a 4S shop to check whether the fuel supply pressure and intake pressure sensor are functioning properly. Abnormal fuel pump pressure or incorrect readings and poor performance of the intake pressure sensor can also cause the car to shake.
19
4
Share

Does the replacement of the front windshield for Skoda Octavia require an original factory part?

Skoda Octavia front windshield replacement does not require an original factory part. Windshield: The function of the windshield is to provide a survival space for passengers. When impacted and shattered, the glass breaks into small pieces with blunt edges, minimizing harm to occupants. Currently, most car front windshields are made of laminated tempered glass or zoned tempered glass, which can withstand strong impacts. Zoned tempered glass is a new type of tempered glass that undergoes special treatment to maintain a certain level of clarity when cracked upon impact, ensuring the driver's field of vision remains unaffected. Precautions for windshield replacement: Do not wash the car for three days after replacing the windshield. Remove the tape securing the windshield position after three days. Avoid driving on excessively bumpy roads, sudden braking, and rapid acceleration to prevent windshield displacement. Do not insert parking permits or other cards into the gap between the front windshield and the dashboard. Avoid driving on highways and keep the maximum speed below 80 km/h. Do not apply window tinting within seven days. After rear windshield replacement, do not open the windows while driving for three days to prevent displacement caused by wind pressure.
14
1
Share

How to Set the Tire Pressure for Buick Verano?

Buick Verano tire pressure setting method: Select the tire pressure mode on the dashboard, press and hold the checkmark button to enter the learning mode, then inflate and deflate the tires in sequence to complete the setting. The dimensions of the Buick Verano are: length 4723mm, width 1802mm, height 1476mm, with a wheelbase of 2700mm. The Buick Verano is equipped with a 1.3L three-cylinder turbocharged engine, delivering a maximum horsepower of 165PS, maximum torque of 240Nm, and maximum power of 121kW. The maximum power speed is 5600rpm, and the maximum torque speed ranges from 1500 to 4000rpm. It is paired with a CVT continuously variable transmission.
2
4
Share

What Causes Manual Transmission Shudder During Startup?

Manual transmission shudder during startup is caused by: 1. Insufficient engine power; 2. Loose connection between the transmission and chassis; 3. Uneven engagement of the clutch pressure plate and clutch friction disc. The correct method for starting a manual transmission is: 1. Fully depress the clutch; 2. Shift into first gear; 3. Turn on the left turn signal; 4. Sound the horn as a reminder; 5. Release the handbrake; 6. Gently lift the clutch with the left foot; 7. As the vehicle begins to move, stabilize the clutch with the left foot, avoiding any pressing or lifting to prevent stalling. Hold steady for 3 seconds, then slowly release the clutch while gently pressing the accelerator with the right foot. Gradually release the accelerator, fully depress the clutch to shift to second gear, and repeat the process to shift to third gear, ensuring a smooth and stable vehicle startup.
19
1
Share

What engine is used in the Toyota RAV4?

The Toyota RAV4 is equipped with 2.0L and 2.5L naturally aspirated engines. The 2.0L engine has a maximum power output of 126kW and a maximum torque of 209Nm. In terms of the transmission system, the 2.0L engine is paired with a CVT continuously variable transmission. The 2.5L engine delivers a maximum power of 178kW and is matched with an eCVT continuously variable transmission. The Toyota RAV4 has dimensions of 4570mm in length, 1845mm in width, and 1715mm in height, with a wheelbase of 2660mm. It has a minimum ground clearance of 195mm and a curb weight of 1420kg.
5
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.