How to Remove the Rear Seats of a Haval H6?

What to Do When There's Gas Coming Out of the Small Hole Next to the Car Battery?

Add distilled water to slightly below the original water level mark, and use a hydrometer to measure the specific gravity, which should be between 1.25-1.29g/cm³ (at 15°C). If the specific gravity is appropriate, continue adding distilled water to the original water level mark. If the specific gravity is low, add replenishing fluid until the specific gravity is correct. Let the battery stand for 3-6 hours, and only charge it when the electrolyte temperature is below 35°C. The charging time should be about 3-4 hours. During the charging process, when the voltage of a single cell in the battery rises to 2.4V, more bubbles will start to appear in the electrolyte. At this point, the charging current should be halved. After charging is completed, a discharge test should be conducted to ensure that the battery is not just superficially charged due to sulfation damage. If sediment is observed before charging, the battery should be replaced.

5

1

Share

Is it necessary to install underbody armor for Camry?

It is necessary to install underbody armor for Camry, as it can protect the chassis components from damage when driving in harsh road conditions. Below is a relevant introduction to automotive underbody armor: 1. Overview: The technical term for automotive underbody armor is automotive underbody anti-collision, anti-rust, and sound insulation coating ("UNDERCOATING" primer), a high-tech adhesive rubber asphalt coating. It is non-toxic, has high coverage and adhesion, and can be sprayed on exposed parts of the vehicle such as the chassis, wheel hubs, fuel tank, lower body panels, and trunk. It quickly dries to form a strong, elastic protective layer. 2. Functions: Underbody armor can effectively protect the chassis from impacts by road gravel, prevent minor scraping and friction, guard against corrosion from acids, alkalis, and salts on the chassis plates, prevent loosening of chassis screws, reduce noise transmission during driving to enhance driving tranquility, and block heat conduction from the chassis plates, keeping the cabin warm in winter and cool in summer.

3

5

Share

Where is the cabin air filter located in the Changan CS95?

Changan CS95's cabin air filter is located behind the glove compartment. To replace the cabin air filter, the glove compartment must be removed. The specific steps are as follows: 1. Open the glove compartment, there is a clip on the right side, pinch the pointed end of the clip to push the telescopic rod out to the left; 2. There is a knob on each side of the glove compartment, unscrew them to remove the knobs; 3. Remove the glove compartment; 4. Inside the glove compartment, you will find a square plastic cover, pry it off; 5. You will see a rectangular cover with clips on both sides, press the clips to open the cover, and you will find the cabin air filter. The Changan CS95 measures 4949mm in length, 1930mm in width, and 1790mm in height, with a wheelbase of 2810mm. It is powered by a Blue Whale 2.0T direct-injection engine, delivering a maximum horsepower of 232 HP, maximum power of 171 kW, and maximum torque of 360 Nm, paired with an Aisin 6AT transmission.

2

Share

Is the height of the Revere R600 too high?

Revere R600's height is just right. Here are the details: 1. Introduction: The exterior dimensions of the Revere R600 are 5940x2110/2140x2835/2940mm (varies depending on optional configurations), with a capacity for four people, blue license plate, and only a C-class driver's license required. The height of less than three meters fully demonstrates the flexibility and passability of a Type B vehicle, making it suitable for a wider range of driving scenarios. The vehicle body adopts an original factory cage structure + welding-free modification process, with balanced design and upgraded insulation layer. The whole vehicle is treated with thermal break insulation and soundproofing (patent protected), giving it outstanding performance in insulation, heat insulation, noise reduction, and soundproofing, greatly improving the comfort of living. 2. Power: The vehicle is based on the SAIC Maxus V90 long-wheelbase ultra-high roof chassis, providing more spacious interior compared to general Type B vehicles. It is equipped with an SAIC π 2.0T diesel engine, paired with a French Punch 6AT automatic transmission, meeting the National VI emission standards while delivering a maximum power of 110KW and a peak torque of 375N·m.

20

4

Share

What is a Hydraulic Coupling?

Hydraulic coupling, also known as fluid coupling, is a hydrodynamic device used to connect a power source (typically an engine or motor) to a working machine, transmitting torque through changes in the angular momentum of the fluid. Below is an introduction to hydraulic couplings: In automotive applications, the pump wheel of the hydraulic coupling is connected to the engine's flywheel. Power is transmitted from the engine crankshaft, and the fluid circulates between the pump wheel and the turbine, transferring torque from the engine to the transmission to drive the vehicle forward. The advantages of hydraulic couplings include flexible transmission, automatic adaptation, shock absorption, and torsional vibration isolation. They improve the starting capability of the power source, enabling it to start under load or no-load conditions. They also provide overload protection, preventing damage to the motor and working machine when external loads exceed limits. Additionally, hydraulic couplings offer energy-saving benefits by reducing the motor's starting current and duration, minimizing grid impact, and lowering the motor's installed capacity. For high-inertia, hard-to-start machinery, torque-limiting hydraulic couplings are used, while centrifugal machinery benefits significantly from speed-regulating hydraulic couplings. Except for bearings and oil seals, there is no direct mechanical friction, resulting in low failure rates and long service life.

18

2

Share

Is Exhaust Modification Illegal?

Modification of a vehicle's exhaust system is not permitted and constitutes illegal activity. Below is a detailed explanation regarding modifying a vehicle's exhaust system: 1. Vehicle exhaust systems cannot be modified. Neither technical modifications nor aesthetic alterations (such as decorative tailpipes) are allowed. Typically, offenders face fines ranging from 200 to 2000 yuan, are ordered to restore the original setup, and have the modified parts confiscated. Severe cases involving excessive noise and public disturbance may result in administrative detention. 2. Permitted vehicle modifications in China include: body color, wheels, exterior decorations, interior, bumpers, and headlights.

13

1

Share

How to Remove the Rear Seats of a Haval H6?

What to Do When There's Gas Coming Out of the Small Hole Next to the Car Battery?

Is it necessary to install underbody armor for Camry?

Where is the cabin air filter located in the Changan CS95?

Is the height of the Revere R600 too high?

What is a Hydraulic Coupling?

Is Exhaust Modification Illegal?

Where is the VIN located on a Cadillac ATS?

What to Pay Attention to When Sleeping in the Car at Night

What are the reasons why the Roewe 350 cannot start after a collision?

Can a Car Windshield Be Repaired?