How to Remove the Rear Headrest of a Volvo XC40?

1 Answers
VanBarrett
07/30/25 7:22am
Volvo XC40 rear headrest removal method is as follows: 1. Locate two grooves approximately 10 cm below the headrest at the back of the seat (position: one on each side, near the seat leather stitching). 2. Inside the grooves, there are two clips. Press both clips in the grooves firmly, then lift the headrest upwards to remove it. Below is relevant information about headrests: 1. To minimize head and neck injuries in collisions, it is crucial to control neck twisting to the smallest extent possible. A well-designed and properly installed headrest is essential for this. 2. The headrest should be installed at least parallel to the top of the ears or approximately 8.89 cm below the passenger's head. 3. The gap between the back of the head and the headrest should be as small as possible, preferably not exceeding 10.16 cm.
Was this review help?
18
3
Share
More Forum Discussions

Can a car involved in a fatal accident be traced after transfer?

It can be traced. You can inquire at the vehicle management office or traffic police department. Below is relevant information about vehicle transfer: Introduction: Vehicle transfer refers to the change of ownership of a vehicle. When buying a used car, besides checking the condition of the car, the most important step is completing the transfer procedures. Principle: Every car has a fixed registration, which mainly records the owner and address of the car, as well as some relevant car parameters. When there are issues with the car, such as involvement in an accident, failure to undergo annual inspection, being a stolen vehicle, or a smuggled vehicle, the transfer cannot proceed through normal procedures.
11
5
Share

What are the signs that a motorcycle spark plug needs to be replaced?

Symptoms indicating that a motorcycle spark plug needs replacement: difficulty starting, reduced power, excessive exhaust emissions, and increased fuel consumption; severe spark plug damage, with signs such as blistering at the tip, black streaks, cracking, or electrode melting. Methods to determine if a spark plug is damaged: Remove the spark plug and observe its appearance to assess its condition. A normal spark plug's insulator skirt and electrodes should appear gray-white, gray-yellow, or light brown. A properly functioning spark plug has a reddish-brown insulator skirt, an electrode gap between 0.8-0.9mm, and no signs of electrode burn. If the spark plug is covered in oil or deposits but is not damaged, it can continue to be used after cleaning off the oil and deposits. If the spark plug is severely damaged, showing signs like blistering, black streaks, cracking, or electrode melting, the cause of the damage should be identified. After troubleshooting, replace the spark plug with a new one. Additionally, if the spark plug appears black as if smoked, it indicates the wrong heat range was selected or the air-fuel mixture is too rich, with oil creeping up.
8
5
Share

Where is the motorcycle's three-way catalytic converter located?

The motorcycle's three-way catalytic converter is generally located inside the motorcycle's exhaust pipe, resembling a long water bottle-shaped device. Definition of the three-way catalytic converter: The three-way catalytic converter is the most important external purification device installed in a vehicle's exhaust system. It converts harmful gases such as CO, HC, and NOx emitted from vehicle exhaust into harmless carbon dioxide, water, and nitrogen through oxidation and reduction reactions. Cleaning the three-way catalytic converter: The cleaning method for the three-way catalytic converter is the drip-feed cleaning process. This method involves connecting a plastic hose to the engine's vacuum solenoid valve and using the air pressure in the hollow tube to draw the cleaning agent from the infusion bottle into the engine. As the cleaning agent is expelled through the exhaust pipe, it cleans the three-way catalytic converter.
1
5
Share

Should a right-turning vehicle yield to a left-turning vehicle or vice versa?

Right-turning vehicles should yield to left-turning vehicles. Below are the relevant details: Traffic regulations: According to the "Implementation Regulations of the Road Traffic Safety Law of the People's Republic of China," when motor vehicles pass through an intersection without traffic signals or traffic police direction, a right-turning vehicle from the opposite direction must yield to a left-turning vehicle. If a traffic accident occurs due to a right-turning vehicle failing to yield to a left-turning vehicle, the right-turning vehicle will bear full responsibility. Right-of-way: Right-turning vehicles do not need to wait for a traffic signal and can turn at any time. To ensure relatively fair right-of-way, most countries generally stipulate that right-turning vehicles have the lowest right-of-way. They must not only yield to left-turning vehicles from the opposite direction but also to vehicles and pedestrians going straight from intersecting directions.
17
2
Share

How many times should the high and low beams be alternated in Subject 3?

No less than two times. Below is a related introduction to Subject 3: Introduction: Subject 3, including the road driving skills test and the safe and civilized driving knowledge test, is part of the motor vehicle driver's license assessment. It is the abbreviation for the road driving skills and safe and civilized driving knowledge test subjects in the motor vehicle driver's test. Test Content: The road driving skills test for Subject 3 includes large buses, tractors, city buses, medium-sized buses, large trucks, small cars, small automatic transmission cars, low-speed cargo trucks, and small automatic transmission passenger cars for the disabled, among others.
8
1
Share

Can the rearview mirror be adjusted during the Subject 2 driving test?

During the Subject 2 driving test, the rearview mirror can be adjusted. After the test starts, you can adjust it before moving on to the next test item, but only inside the car. Your hands must not extend out of the window, and you cannot get out of the car to adjust it. Therefore, it is recommended to adjust the mirrors before the test begins. Below are the methods for adjusting the rearview mirrors of the test vehicle for Subject 2: After getting into the car, adjust the seat and backrest to maintain a normal driving posture, then proceed to adjust the rearview mirrors. The adjustment buttons for the rearview mirrors are located on the inner side of the front doors and can be adjusted in four directions: up, down, forward, and backward. Method for adjusting the left rearview mirror: Maintain an upright sitting position. When adjusting left and right, ensure the car body occupies one-third of the mirror's surface. When adjusting up and down, position the rear door handle near the upper edge of the left rearview mirror. Method for adjusting the right rearview mirror: Similarly, maintain an upright sitting position. When adjusting left and right, ensure the car body occupies one-third of the mirror's surface. When adjusting up and down, position the rear door handle near the upper edge of the right rearview mirror.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.