How to Remove the Navigation System in Hyundai ix35?

[DeJoel]

The steps to remove the navigation system in Hyundai ix35 are as follows: 1. First, remove the top cover; 2. Take off the lower cover with the hazard light switch; 3. Gently pry along the gap using a hard plastic tool or similar item to reveal four screws; 4. Finally, unscrew the screws to remove the navigation system. The Hyundai ix35 is a compact SUV under the Hyundai brand, with dimensions of 4500 mm in length, 1850 mm in width, and 1710 mm in height, and a wheelbase of 2640 mm. The ix35 is equipped with two engines: a 1.4-liter turbocharged engine and a 2.0-liter naturally aspirated engine.

[DiCaroline]

Removing the navigation system in a Hyundai ix35 requires some finesse. Last time I tried it myself, I found it quite easy to damage if not careful. Having a set of plastic pry tools is crucial—metal tools are absolutely out of the question as they will leave scratches. Start by prying open the decorative cover from the passenger side of the center console; it's held by clips, so stop when you hear a click. Underneath the panel, you'll find four cross-head screws—remove them all and gently pull out the head unit. Remember to take photos of the wiring harness connections at the back before disconnecting them, and don't yank the plugs—press the clips to release them. Take your time during the whole process and avoid using excessive force. When reinstalling, just follow the reverse order to put everything back together.

[AngelinaFitz]

I think the key to removing the navigation system lies in preparation. Disconnect the negative terminal of the battery half an hour in advance for safety. A flat-headed plastic pry bar works better than a metal one, and one with a suction cup makes it easier to remove the panel. Start by prying at the seam along the top edge of the air conditioning panel, applying gradual force until the clips loosen. The head unit is usually secured with T20 screws—don’t overlook any hidden screws in the trim gaps. The thickest connector at the back is the antenna interface; press the clip and rotate it 90 degrees. Remember to align the power plug with the triangular marker. Don’t rush—take the opportunity to clean out the dust from the vents while you’re at it.

[VonManuel]

Sharing some hands-on experience from disassembling the ix35 navigation unit twice. After power disconnection, start prying from the bottom of the panel while cushioning with a soft cloth to avoid marks. Don't rush to pull out the head unit after removing screws - the GPS and USB cables are hidden on the left side and need disconnecting first. All connectors have foolproof designs but require straight vertical force during insertion/removal to avoid bending pins. Support the bottom during entire removal to prevent frame deformation, especially since plastic parts become brittle in cold weather. During reassembly, align all connectors properly before pushing fully to avoid rework.

[ORafael]

Before removing the navigation unit, prepare three tools: plastic pry tools, a magnetic screw tray, and a small flashlight. First, carefully observe the panel seams to avoid prying incorrectly—the center console's large curvature makes it easy to misalign. Mounting screws are usually hidden inside the storage compartment, so don't overlook them. The order of disconnecting wiring harnesses is crucial—start with the thinnest radio antenna cable and leave the power cable for last. I recommend labeling wires, especially dual-connector reverse camera cables, for easier reassembly. Wear gloves throughout the process, as electronic components are sensitive to sweat.

[VanLincoln]

Pay attention to three key points: disconnect the negative terminal first to prevent short circuits, use a non-metallic pry tool, and take photos to record the wiring sequence. The most convenient way to start disassembly is from the passenger side—a gap as wide as a fingernail is enough to insert the tool. There are eight clips with force points; pry them outward evenly and stop when you hear a clicking sound. After removing the four 8mm cross screws, support the bottom shell of the main unit and pull it out horizontally. The key is to pinch the blue latch when unplugging the main power connector, and the GPS antenna can be removed by turning it clockwise. When reassembling, connect the wires first, then secure the clips, and finally tighten the screws.