How to remove the maintenance wrench indicator on JAC Refine S3?

1 Answers
MacLaila
07/29/25 6:27pm
The method to remove the maintenance wrench indicator on JAC Refine S3 is: 1. Turn off the ignition switch; 2. Press and hold the adjustment rod at the lower right of the instrument panel; 3. Turn the ignition switch to the ON position; 4. After approximately 5 seconds, the maintenance indicator light will turn off, at which point you can release the adjustment rod. The JAC Refine S3 is positioned as a compact SUV, with body dimensions of 4345mm in length, 1765mm in width, and 1640mm in height, and a wheelbase of 2560mm. In terms of exterior design, the Refine S3 adopts a new design language, giving it high recognition and a fashionable appearance.
Was this review help?
10
5
Share
More Forum Discussions

How Long is the Shelf Life of Opened Engine Oil?

Here is the relevant introduction about the shelf life of engine oil: 1. Unopened engine oil: The shelf life is generally about 5 years, and there are also engine oils with a shelf life of more than ten years. 2. Engine oil poured into the engine: For engine oil that has been poured into the engine and used occasionally, such as for cars that are not driven for long periods, if the oil was changed recently and the car will be left unused for a long time, it is recommended to replace the oil after more than 6 months. If the engine oil in the car has been used for a relatively long time, the storage period should be shortened, and it is recommended to replace it after more than 3 months of storage before the next use. 3. Remaining engine oil after maintenance: The remaining engine oil after maintenance can be stored for about 1 year if properly preserved, but the best recommendation is to use it up within half a year.
5
5
Share

Does Using Car Air Conditioning in Winter Consume More Fuel?

Using the heater in your car during winter does not increase fuel consumption. Here is some relevant information about car heating: 1. Heat Source: The warm air comes from the heat generated by the engine during operation. When the engine's cooling system dissipates heat from the engine, a fan directs this heat into the car to create warm air. When the heater is not in use, the fan stops, and the heat vent closes, allowing the heat to dissipate into the atmosphere. Therefore, car heating is a form of waste heat recycling and does not consume additional fuel. 2. AC Button: The AC button controls the air conditioning compressor. In summer, when using air conditioning, you must press the AC button to activate the cooling function. However, the heater simply utilizes the car's internal heat circulation and does not require the air conditioning compressor to be turned on. Thus, to use the heater, you only need to adjust the air conditioning controls without pressing the AC button.
4
1
Share

Where is the engine number located on the Hawtai Santa Fe?

The engine number of the Hawtai Santa Fe is located below the third cylinder spark plug on the left side of the engine. It typically consists of a combination of 7 to 8 digits and letters. In addition to the above method, the engine number can also be checked through the following 4 ways: The vehicle license displays the engine number, usually located on the second-to-last line; The motor vehicle registration certificate will indicate the engine number; The car purchase invoice will specify the engine number; The vehicle purchase tax payment certificate will indicate the engine number. It should be noted that the engine number is not the same as the engine model. The engine model refers to the specifications and size of the engine within the manufacturer, and engine models can be the same. The engine number refers to the production number of the engine, where each engine can only use one engine number and each engine's number is unique.
15
1
Share

Should refrigerant be added from the high-pressure or low-pressure side in a car?

Refrigerant can be added to a car's air conditioning system through either the high-pressure or low-pressure pipe. The methods for adding refrigerant to a car's air conditioning system are as follows: 1. High-pressure side charging: Suitable for charging after leak detection and vacuuming. This method requires the compressor to remain off, the engine must be stopped, and the refrigerant tank must be inverted. 2. Low-pressure side charging: This involves adding gas, characterized by a slower charging speed, and is typically used for topping up refrigerant. Since the high-pressure pipe is too dangerous, refrigerant is generally added through the low-pressure pipe. Pressure must be monitored in real-time to avoid excessive levels, which could damage the air conditioning system. 3. Refrigerant can also be added to the high-pressure side when the engine is static. It is difficult to add Freon while the engine is running, so it is recommended to add refrigerant through the low-pressure side.
2
1
Share

What to Do When a Tire Blows Out?

When a car tire blows out, you can handle the situation through the following steps: 1. If a tire blows out, stay calm. If the car veers off the main lane due to a flat tire, the driver should not apply emergency braking, as this could lead to a more severe traffic accident. 2. When the driver realizes a tire has blown out, they must firmly control the steering wheel. If the car starts to swerve, avoid overcorrecting; instead, gently slow down the vehicle while maintaining control of the direction. Avoid emergency braking at all costs. 3. Hold the steering wheel with both hands, try to keep the car moving straight, then release the accelerator and either lightly tap the brakes or do nothing, allowing the car to slow down gradually. Throughout this process, avoid making any sudden movements, as they could cause the car to roll over or spin out. 4. Try to park the car in a relatively safe location, turn on the hazard lights, and place a warning triangle behind the vehicle. 5. Have all passengers exit the car and move to a safe area. 6. Call for roadside assistance or replace the tire with a spare.
13
5
Share

What is the Minimum Ground Clearance?

It refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when the vehicle is fully loaded and stationary. Relevant introduction to minimum ground clearance: The design of the minimum ground clearance must consider the passability when loading and unloading on transport platforms, as well as the possibility of avoiding scratches when the car is close to the edge of ordinary sidewalks. If the vehicle is restricted to sales in a specific country or region, the local road quality conditions must also be taken into account. The value of the minimum ground clearance has certain limitations, which are related to the vehicle's function and aerodynamics. For example, sports cars usually have a smaller minimum ground clearance, while SUVs have a larger one. Generally speaking, the minimum ground clearance for sedans ranges between 110 mm and 150 mm. For sedans, a larger ground clearance (over 130 mm) provides relatively better passability but poorer high-speed stability; a smaller ground clearance (below 110 mm) offers better high-speed stability but poorer passability. Nowadays, models equipped with air suspension can automatically adjust the ground clearance, better meeting the dual needs of passability and high-speed stability.
9
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.