How to Remove the Exterior Handle of a 2020 Bora?

1 Answers
Leo
07/30/25 3:59am
Tap off the small black cover to reveal a Torx 20 screw. Hold the door handle without releasing it, then loosen the Torx 20 screw until the door handle has a noticeable resistance and locks in place. For the decorative cover, as indicated by the red circle. Hold the door handle and apply force in the direction of the arrow. The door handle can then be removed.
Was this review help?
15
2
Share
More Forum Discussions

How to Use the Navigation System in Corolla Hybrid?

Enter the navigation map and input your destination in the search bar at the top. Tap the blue "Go" button at the bottom right corner to automatically detect the route. The system will automatically mark the simulated route from the starting point to the destination. Click "Start Navigation" for the system to display the route and walking directions.
3
5
Share

How to Adjust the Rearview Mirror on the Buick Excelle?

Enter the vehicle and check if the rearview mirror angle is appropriate. The rearview mirror adjustment switch can be found on the left side of the center console. Rotate the knob to the middle "0" position to turn off the rearview mirror adjustment function, and rotate the knob to the "R" position to select the right rearview mirror for adjustment. Rotate the knob to the "L" position to select the left rearview mirror for adjustment. Press the knob in different directions to adjust the rearview mirror accordingly.
10
5
Share

How to Play Music via Bluetooth in a 2012 Buick Regal?

Turn on both your phone's Bluetooth and the car's Bluetooth, ensuring they are in discoverable mode. On your phone's Bluetooth interface, click 'Search for Devices'. Select the car's Bluetooth as displayed on your phone, then click on the car's Bluetooth -> Bluetooth Settings -> Pair. If the pairing code is entered correctly, the car's Bluetooth will soon display 'Connected'.
7
5
Share

How to Install the Applied ETC?

ETC installation method is as follows: Upon receiving the device, first check if the ETC card and electronic tag (OBU) are damaged. Press the anti-tamper button on the back of the OBU, the red light will briefly illuminate, and the OLED screen will display "Label Invalid" and "Please Insert Card," indicating the device is functioning normally. Clean the front windshield, ensuring the glass surface is smooth, clean, and dry. Then peel off the protective film on the back of the OBU adhesive and stick it to the installation position. Press firmly for 2-3 minutes to remove air bubbles. Insert the ETC card with the front facing the driver and the back facing the front glass, ensuring the chip is inserted into the OBU device. Where can ETC be installed: For small vehicles such as cars and minivans, the OBU device should be installed on the upper middle part of the front windshield. For large vehicles like trucks and buses, the installation position is on the lower middle part. ETC installation position requirements: The height should not be less than 1.2 meters or more than 2.5 meters; the installation angle N should be between 30º and 90º (the angle between the electronic tag surface and the horizontal plane).
17
4
Share

How to Remove the Taillight of Mazda Axela?

After opening the trunk, first remove the inner lining fabric on one side of the taillight. Pry open these clips and pull the lining fabric aside by hand. Take out a small ratchet wrench and remove the nuts one by one, keeping them safe. Unplug the wiring harness connector by hand. After unplugging the wiring harness connector, hold both sides of the taillight with your hands and gently pull outward to remove it.
7
1
Share

How to Drive a Volkswagen Lamando Automatic Transmission?

First, enter the vehicle and press the brake pedal with your right foot. After pressing the brake pedal, start the vehicle. Once the vehicle is started, you can release the brake pedal. After shifting to D gear, release the handbrake.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.