How to remove the door panel of Baojun 730?

[AveryLee]

Steps to remove the door panel of Baojun 730: 1. Remove the panel in the triangular area inside the door, which is located at the upper left corner of the door interior; 2. There is a small clip inside the triangular area. After removing the clip, unscrew the fixing screw on the handle; 3. Starting from the lower rear or lower front corner of the front door, pry up all 7 clips of the front door trim panel one by one, then use tools to remove the door panel; 4. During the disassembly process, pay attention to protecting the interior components to avoid damaging the wires inside the door and prevent surface scratches. The Baojun 730 is a family MPV product under SAIC-GM-Wuling Baojun, with a body length, width, and height of 4780mm, 1820mm, and 1755mm respectively, and a wheelbase of 2750mm. It is powered by 1.5L and 1.8L engines, paired with a 5-speed manual transmission.

[LaGeorge]

Removing the door panel of the Baojun 730 is actually quite simple. I've done it myself several times recently. First, prepare the tools: a Phillips screwdriver and a plastic pry bar—avoid using metal tools to prevent scratching the door panel. The screws are hidden inside the door handle and beneath the lower trim panel. After unscrewing them, gently pry the plastic clips along the edge of the door panel. Apply even force when prying and avoid pulling too hard to prevent the clips from breaking. Once removed, remember to disconnect the power window connector to avoid short circuits. The whole process should be done slowly and takes about 10 minutes. I recommend doing it in a garage or indoors, not during rainy weather. After removal, you can clean dust or replace components, such as speakers or switches. DIY saves on repair costs, and I think it's totally worth it.

[SanEmmanuel]

Safety is the top priority when removing door panels. I always disconnect the battery first. Prepare a Phillips screwdriver and a plastic pry tool. The door panel screws are located inside the door handle and beneath the lower trim panel. Apply force parallel when gently prying open the clips to avoid damage from tilting. Note the positions of electrical connectors before disconnecting them to prevent mistakes. Wear gloves throughout the process for protection and avoid working in dirty environments. The removal process isn't difficult and is suitable for beginners, but if you lack experience, it's best to watch tutorial videos first and confirm each step before proceeding. After removing the door panel, check if all components are intact and replace any clips if necessary to prevent looseness.

[Pat]

My experience removing the door panel of the Baojun 730 is quite simple. First, use a screwdriver to remove the screws inside the door handle. Then, use a plastic pry tool to gently lift the panel from the bottom upwards until you hear the clicking sound of the clips loosening. Carefully disconnect the wiring before lifting the panel off. Be cautious not to apply excessive force to avoid breaking the clips. Checking the manual or a tutorial video beforehand can make the process smoother. It only took me a few minutes the first time I did it, making it quite suitable for beginners.

[DiCaden]

Last time the window switch of my Baojun 730 broke, I personally removed the door panel to fix it. The steps were: use a Phillips screwdriver to unscrew the screws on the door handle, about two or three points. Then use a plastic pry bar to slowly pry open the clips on the edge of the door panel, applying force evenly without yanking. When disconnecting the wire connectors, handle them gently. I operated in the garage, ensuring safety and saving money throughout. After removal, internal parts could be replaced or wiring checked, and don't forget to wear gloves for protection during the operation. The whole process was easy and quick, and I got it done in just 15 minutes.

[Joe]

Removing the Baojun 730 door panel requires some skill. Prepare a plastic pry tool and a screwdriver, as the screws are usually located inside the door handle. After unscrewing, start prying the clips from the bottom of the door panel and gradually work your way up. A common mistake is using too much force, which can break the clips; I recommend prying slowly and patiently. Before disconnecting any wires, confirm their connection points to avoid confusion. Choose a flat surface for the operation, avoiding slopes. After removal, test the window and door functions to ensure they work properly. The entire process is straightforward and takes about 12 minutes, saving you repair costs.