How to Remove the Cruze Center Console Panel?

1 Answers
CarmenFitz
07/29/25 10:38pm
The method to remove the Cruze center console panel is as follows: 1. First, remove the air conditioning control module; 2. Use a trim removal tool to pry loose the upper cover panel of the center console; 3. Remove the upper cover panel of the center console; 4. Use the trim removal tool to pry the air vents on the center console; 5. Remove the air vents, and the center console panel removal is complete. Taking the Cruze 2018 320 Manual Pioneer Edition as an example, its body dimensions are 4666mm in length, 1807mm in width, and 1460mm in height. It is a 4-door, 5-seater sedan with a maximum power of 84kw and a maximum torque of 146nm, equipped with a 1.5L naturally aspirated engine and a 6-speed manual transmission.
Was this review help?
19
2
Share
More Forum Discussions

What is the method for identifying car dashboard warning lights?

Car dashboard warning lights may illuminate due to parking sensor failure, excessively worn brake pads, engine oil pressure sensor malfunction, insufficient brake fluid, fuel cutoff system intervention or failure, etc. The identification methods are as follows: A triangle with an exclamation mark in the middle indicates a general fault warning light, which may illuminate under the following circumstances: Overheating of the dry dual-clutch transmission clutch. Fuel cutoff system intervention or malfunction. Parking sensor failure. External light malfunction. Engine oil pressure sensor failure. Traction control system warning or failure. A circle with an exclamation mark in the middle and parentheses around it indicates a brake system warning light, which may illuminate under the following conditions: In some vehicles, it lights up for a few seconds when the ignition is turned on and turns off after the engine starts. It lights up when the handbrake is engaged and turns off when released. It lights up during driving if the brake fluid level is too low. It lights up when there is a brake system malfunction. A horizontal line with an exclamation mark in the middle and parentheses below it indicates a tire pressure monitoring warning light, which lights up when the pressure in one of the vehicle's tires is too low.
1
4
Share

Which car has a large V-shaped logo?

The representative model parameters of Mazda and Changan automobiles are as follows: Mazda Atenza 2021 model: Body dimensions: Length 4870mm, width 1840mm, height 1451mm, wheelbase 2830mm, front track 1595mm, rear track 1585mm. Power: Equipped with a 2.5L naturally aspirated engine, maximum horsepower 192hp, maximum power 141kw, maximum torque 252nm, paired with a 6-speed automatic transmission (AT), front suspension MacPherson strut independent suspension, rear suspension multi-link independent suspension. Changan CS35PLUS 2021 model: Body dimensions: Length 4335mm, width 1825mm, height 1660mm, wheelbase 2600mm, front track 1570mm, rear track 1570mm. Power: Equipped with a 1.6L naturally aspirated engine, maximum horsepower 128hp, maximum power 94kw, maximum torque 161nm, paired with an 8-speed continuously variable transmission (CVT), front suspension MacPherson strut independent suspension, rear suspension torsion beam non-independent suspension.
18
5
Share

What are the types of car floor mats?

Car floor mats include full-coverage mats, carpet mats, and rubber mats. Full-coverage mats, when placed in the car, can completely enclose the space under the feet, preventing dust or water stains from spreading everywhere in the car. Full-coverage mats are also called 3D mats, as they have a concave shape. Carpet mats have strong dirt absorption but are troublesome to clean. As the name suggests, carpet mats have a looped structure that effectively traps dust and dirt inside, making them excellent at absorbing dirt. However, if not cleaned frequently, they can easily breed bacteria. Additionally, carpet mats have a smaller coverage area compared to full-coverage mats. Rubber mats were once favored by many consumers due to their advantages such as being dirt-resistant, easy to clean, and inexpensive. However, during use, it was found that rubber mats are slippery and less safe. Moreover, inferior mats produced by low-quality manufacturers can emit harmful odors, significantly reducing their popularity.
4
0
Share

How to Avoid Crossing the Line in Subject 2?

For navigating S-curves, there is a mnemonic technique: "Left point aligns with the right line, right point aligns with the left line." The left and right points refer to the top corners of the car's front. This means when turning in a particular direction, use the corresponding top corner to follow the opposite side's road edge line. Below is an introduction to Subject 2: Definition: Subject 2, also known as the small road test, is part of the motor vehicle driver's license assessment, specifically referring to the field driving skills test. Objective: Master the basic driving operation essentials and possess fundamental vehicle control abilities; proficiently grasp the basic methods of field and road driving within the test area, capable of reasonably using vehicle controls and correctly managing the vehicle's spatial position, ensuring accurate control over the vehicle's position, speed, and route.
17
5
Share

What to Do If You Fail the Driver's License Medical Examination?

You can definitely go for the medical examination first. If you indeed fail, you should go to the hospital to determine whether color weakness affects driving. During the registration medical examination, there are two sets of color tests: one is a complex pattern combination, and the other consists of independent red, green, and yellow dots. If that still doesn't work, go to the hospital to get a certificate, then take this certificate to the driver's license medical examination center, and there should be no problem. After submitting the medical report to the DMV, you can normally register and schedule the exam.
15
1
Share

Can I replace just one shock absorber on a sedan?

You can replace just one shock absorber on a sedan, but the effect won't be as good as replacing both. Below is an introduction to the replacement method and function of vehicle shock absorbers: Shock absorber replacement method: Loosen the wheel nuts in a diagonal sequence, remove the wheel, detach the control arm fixing bolts, loosen the fixing nut of the spring support arm, open the engine hood, loosen the upper fixing nut of the shock absorber, remove the shock absorber, replace the damaged components and rubber boot of the shock absorber, apply lubricating grease to improve wear resistance, install the shock absorber, and use a wrench to tighten the wheel fixing nuts. Function of shock absorbers: To suppress the oscillation when the spring rebounds after absorbing shock and to absorb the energy from road impacts.
14
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.