How to Remove the Center Console of Roewe RX5?

[SaraDella]

Method to remove the center console of Roewe RX5: First, the air conditioning control module needs to be removed. Then, use a trim removal tool to pry loose the upper cover of the center console and remove it. Next, use the trim removal tool to pry the air vents on the center console and remove them. This way, the entire center console panel can be detached. The Roewe RX5 is an SUV model under SAIC Roewe, with body dimensions of 4545mm in length, 1855mm in width, and 1690mm in height, and a wheelbase of 2700mm. In terms of power, the Roewe RX5 is equipped with two turbocharged engines, a 1.5T and a 2.0T. The 1.5T engine delivers a maximum power of 169 horsepower and a peak torque of 250 Nm, paired with either a 6-speed manual or a 7-speed dual-clutch transmission. The 2.0T engine offers a maximum power of 220 horsepower and a peak torque of 350 Nm, matched with a 6-speed dual-clutch transmission.

[DePaul]

I've helped someone disassemble the Roewe RX5's center console before, and the whole process requires careful operation. First, turn off the engine and disconnect the negative battery terminal to prevent short circuits or sparks causing hazards. Then, check around the edges of the center panel and below the air vents, as screw holes are often hidden there—use a small pry tool to remove the decorative covers and take out the screws. After removing all screws, gently separate the panel clips without forceful pulling to avoid clip breakage or interior scratches. Roewe's design is relatively user-friendly, but I once encountered a loose wiring harness that needed reconnecting—fortunately, it wasn't a big issue. When reassembling, align the parts properly and secure each clip and screw to ensure a tight fit. The whole job takes about half an hour with patience, and using plastic pry tools is safer than metal ones. After disassembly, you can clean out dust inside or install small accessories, which is quite fun, but beginners should seek guidance from experienced hands to avoid mistakes.

[OKaylee]

When disassembling the Roewe RX5 center console, extra caution is required. Here's my advice: Always disconnect the battery first to avoid electric shock or circuit damage. The disassembly steps include consulting the vehicle manual to locate hidden screws (typically at the four corners of the center panel and under storage compartments), gently prying off covers with plastic tools, then removing screws. Carefully release panel clips afterward - avoid using excessive force to prevent damaging plastic components or internal wiring. When I attempted to clean the AC vents myself, a clip broke off and I had to purchase replacement parts, wasting both time and money. The main risks involve damaging electronic components (e.g., wiring harness short circuits), so if you're unsure, it's better to consult professional 4S shop technicians for faster, more reliable repairs. The entire process requires patience and proper tools - never rush the procedure to ensure driving safety.

[GeorgeLee]

As a DIY-loving owner, removing the center console of the Roewe RX5 is not difficult. Disconnect the battery and prepare plastic pry tools and a small screwdriver. Look for screw holes, often located near panel trims or the ashtray. Pry open the cover and unscrew the bolts. Gently separate the clips with light force to avoid breakage. The spacious interior allows for adding equipment like USB charging cables, which is super cool. After completion, reinstall by aligning properly. Use patience and be careful not to damage the wiring harness. Simple tools are all you need to get it done.

[FranciscoDella]

I installed a navigation system on my Roewe RX5 and had to dismantle the center console. First, I disconnected the negative battery terminal to avoid any risks. Finding the screw holes was tricky—they were often hidden in small edge recesses, requiring the plastic covers to be pried open. After removing the screws, I gently pushed the panel, but a clip broke, and a wire nearly got damaged. After reassembly, all functions tested fine, but the process was quite a hassle—it took multiple people to hold the panel steady. Roewe's clip design seems prone to damage, so I'd advise assessing your skill level before attempting this. Beginners can easily make mistakes; professional handling is more reliable and helps avoid similar mishaps.