···
Log in / Register

How to Remove the Center Armrest of Magotan B7?

4 Answers
MacEmily
07/29/25 10:38am
Lift up the fabric cover inside. Use a 10# tool to remove the two 10# screws and store the fixing screws properly. Then firmly pull the gear lever handle upwards to release it from the fixing clip. The central gear shift panel is surrounded by clips, simply pull upwards sequentially to release them. Finally, there is a connector underneath the panel, unplug it to remove the armrest completely.
Was this review help?
15
5
Share
LeilaniLee
08/13/25 3:16pm
Actually, I've taken apart the B7 Passat's center console armrest several times, and I've summarized the steps. First, empty everything from the console. At the bottom front of the armrest, there's a small cover plate—just pry it open to reveal two screws, which you can remove with a Phillips screwdriver or hex key. Next, use a plastic pry tool to carefully lift the silver trim strips on both sides of the center console. This will expose the rear mounting screws of the armrest. After removing all these, the entire armrest can be lifted vertically upwards. The trickiest part is the front plastic clips of the armrest—you need to apply a bit of finesse, pressing down slightly while pushing outward. It's best to have some spare plastic clips on hand for the process, as VW's clips are particularly prone to breaking.
Was this review help?
1
4
Share
Expand All
MacGriffin
10/07/25 6:09am
Just helped a friend with this car's center console a couple of days ago, no special tools needed. Take out the rubber mat inside, you'll see four clips at the bottom - they can be released gently with a flathead screwdriver. Push the armrest to its rearmost position, there are two screws on the sides. After removing them, grip both sides of the console and lift upwards - the rear clips will disengage first. The front clips are trickier; you'll need to lift while simultaneously pulling toward yourself. If you hear a click, that means the clip has released. Be careful with the wiring harness on the passenger side - unplug the connector slowly.
Was this review help?
8
0
Share
Expand All
DelLukas
11/20/25 7:33am
Focus on the key steps for disassembly. First, lower the rear cup holder and reach inside to locate a T20 screw at the back that must be removed. Then, lift the front storage compartment to reveal two hidden screws at the bottom—remove these. The most crucial step is to grip the entire console and pull it straight upward to release the rear clips. Avoid forcing the front clips; instead, press the lower tab with your thumb while pushing outward. The whole process takes about 15 minutes. Note that the older B7 model requires an additional step: disconnecting the USB port wiring harness.
Was this review help?
18
4
Share
Expand All
More Forum Discussions

Can You Still Drive When the Oil Life is 0?

When the oil life reaches 0, it is not recommended to continue driving. Here is some extended information about oil life: 1. The vehicle's computer alerts you about oil life based on preset mileage. 2. If the oil life displays as 0, check whether it is due to a data error caused by not resetting after an oil change or prolonged disuse of the oil. 3. Engine oil has a shelf life and cannot be used indefinitely. The shelf life of oil depends on its condition. Unopened engine oil can last up to five years; leftover oil after a car service, being opened, has a shortened shelf life of about one year; oil already poured into the engine has the shortest shelf life, approximately six months. 4. While checking the car's oil, you can use an oil inspection filter paper to test if the oil has deteriorated. By dripping oil onto the filter paper, three important ring-shaped areas can be observed: the deposit ring, the diffusion ring, and the outer oil ring, which indicate the oil's contamination level, the dispersing ability of additives against contaminants, and the oil's oxidation level.
14
1
Share

What are the causes of brake noise after vehicle startup?

Vehicle startup after the brake noise causes are: 1, too slow to release the brake caused; 2, the new replacement of the brake pads running-in is not in place; 3, sand particles into the middle of the brake pads and brake discs; 4, the brake disc fixing screws are lost or damaged; 5, the brake system failure. The brake maintenance methods are: 1, high temperature protection, to prevent the brake system corrosion, to prevent the brake pads due to high temperature surface bite, to eliminate the brake pads scream; 2, regular replacement of brake oil; 3, clean the brake discs, brake drums and any parts of the oil stains, dirt and friction dust, to maintain the brake disc heat dissipation good; 4, regular inspection of the thickness of the brake pads or brake shoes.
13
0
Share

What Causes the Brake Pedal to Be Hard to Press and the Car Unable to Start?

Here are the reasons why the brake pedal is hard to press and the car cannot start: 1. Vacuum booster pump leakage: If the car's vacuum booster pump leaks or malfunctions, the force required to press the brake pedal increases because the brake booster is not functioning properly. If it fails, the brake loses its power assistance, making it difficult to press. 2. Normal phenomenon: The inability to press the brake pedal after the engine is turned off is related to the brake booster pump. The brake booster pump only continuously generates vacuum when the engine is running. When the engine is off, it relies on the remaining vacuum assistance, but this will restore once the engine starts, and it is not a malfunction. Additional info: In driving, to prevent unexpected situations like sudden movement or rolling when starting the car, automatic transmission models are designed to require pressing the brake pedal to start. If the brake pedal is not pressed, the car will not start successfully. Moreover, the gear must be in P (Park) or N (Neutral) when starting an automatic transmission car. If started in N without the handbrake engaged, the car may roll. Therefore, the "press brake to start" design is entirely for safety considerations.
13
2
Share

Is Brake Maintenance Necessary?

Brake maintenance is necessary. Only by timely servicing the components of the brake system and cleaning and lubricating the safety parts can the accuracy and safety of the brakes be ensured. Below are the phenomena that may occur if the brake system is not maintained for a long time: 1. Abnormal noise: The dust from normal wear of the brake pads accumulates near the brake calipers, and if not cleaned for a long time, it can cause abnormal noise; the sound-damping and vibration-damping plates of the brake pads, if not cleaned and lubricated for a long time, can also cause brake noise. 2. Abnormal wear: When driving on gravel roads, some particles may splash between the brake pads and brake discs, causing noise or abnormal wear. 3. Brake deviation: If the dust cover of the sliding shaft of the caliper is damaged, driving through water or mud puddles can cause the caliper shaft to rust and seize, the caliper to not return to position, reduced braking force, and brake deviation.
14
1
Share

What engine does the Peugeot 5008 have?

The Peugeot 5008 is equipped with 1.6T and 1.8T turbocharged engines. A turbocharged engine refers to an engine fitted with a turbocharger. Taking the 2019 Peugeot 5008 as an example, it is a mid-size SUV with the following dimensions: length 4670mm, width 1855mm, height 1650mm, wheelbase 2840mm, and curb weight 1541kg. The 2019 Peugeot 5008 features a MacPherson strut front suspension and a torsion beam rear suspension. It is powered by a 1.6T turbocharged engine producing a maximum horsepower of 170PS, maximum power of 125kW, and maximum torque of 250Nm.
7
5
Share

What engine does the Buick Regal use?

Buick Regal uses a 1.5T turbocharged engine and a 2.0T turbocharged engine. A turbocharged engine refers to an engine equipped with a turbocharger. Taking the 2020 Buick Regal as an example, it belongs to the mid-size car category with a length of 4904mm, width of 1863mm, height of 1461mm, wheelbase of 2829mm, fuel tank capacity of 55L, and trunk capacity of 441L. The 2020 Buick Regal is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 169PS, maximum power of 124kW, maximum torque of 250Nm, and is paired with a 9-speed automatic manual transmission.
1
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.