How to Remove the Bumper of Baojun 730?

[DiJeffrey]

Baojun 730 bumper removal method is: 1. Remove the screws at the bottom of the front bumper; 2. Open the front cover and remove the screws on the frame. The Baojun 730 is an MPV with body dimensions of: length 4780mm, width 1780mm, height 1740mm, wheelbase 2750mm, and a fuel tank capacity of 52 liters. The Baojun 730 is equipped with a 1.5T turbocharged engine, delivering a maximum power of 108kW at 5200rpm, a maximum torque of 250Nm, and is paired with a 6-speed manual transmission.

[VonTalia]

Removing the front bumper of a Baojun 730 is actually quite straightforward. I've done it on several vehicles before—it just requires some patience. First, use a Phillips screwdriver to remove several screws near the wheel arch, and the plastic cover above the wheel also needs to be taken off. Then, bend down to locate the lower part of the bumper, where two large screws need to be loosened—be careful not to apply too much force, as plastic screws can break easily. Next, along the edges of the bumper, especially near the fender, locate three or four small screws and remove them. At this point, gently pry open the clips, as they are secured with plastic fasteners, and slowly pull outward without yanking. Oh, and if the car has fog lights or sensors, disconnect the wiring harness first to avoid damaging the wires. The whole process takes about 20 minutes, and all you need is a screwdriver and gloves. After removal, remember to keep all the screws organized so you don’t lose them when reinstalling. If you're a beginner and feel unsure, watch an online tutorial before attempting it—safety first. Also, regularly inspect the bumper clips to prevent loosening at high speeds, which could cause issues.

[DiCarmen]

I once removed the rear bumper of my Baojun 730 by myself, but ended up breaking some clips due to lack of experience. First, prepare a Phillips screwdriver and a small wrench, and wear old clothes to avoid getting dirty. Start from the wheel area, pry open the wheel cover and remove several screws, then loosen the screws around the bumper. Pay special attention to the two key fixing points at the bottom. Be gentle, as plastic parts are fragile. If the bumper is connected to sensors like radar wires, pressing the connector lightly will separate it. I once pulled too hard and broke a clip, costing me tens of yuan to replace. It's advisable to have an assistant to help hold it, as working alone might accidentally disconnect wires. The whole removal process takes about ten minutes. Afterward, wipe off any dust on the car body and check for rust on the internal brackets. If you encounter any issues, don’t panic—just search for a forum guide.

[LeMatthew]

Removing the Baojun 730 bumper involves three steps: Prepare tools including a Phillips screwdriver, locate and remove screws under the wheel arch and bumper, then gently pull the bumper to release clips. Remember to disconnect wiring harness connectors and keep parts for reassembly. Simple and efficient—avoid forceful pulling to prevent damage.

[LeLeila]

Removing the Baojun 730 bumper is just like what mechanics often say - it's all about screws and clips. Use a Phillips screwdriver to remove the wheel arch screws and bumper mounting screws one by one, about six or seven in total. Then gently push outward to release all the clips without prying forcefully. Be aware there might be wiring harness connections inside the bumper - unplug the connectors carefully to prevent short circuits. When reinstalling, align the position and press to snap it back in place. Check the clip condition regularly during car washes to extend its lifespan. The design is quite user-friendly - it takes about ten minutes to complete, making it convenient for later modifications or scratch repairs.

[TessaMarie]

Before removing the Baojun 730 bumper, first check that the tools are complete - a Phillips screwdriver will suffice. Unscrew the bolts in sequence from the wheel arch to the bottom mounting points, ensuring none are missed. The bumper material is plastic, so pull gently to avoid scratching the car paint. After removal, inventory all parts and realign the slots during reassembly. This process isn't just for repairs, but also helps prevent further damage after accidents. Beginners are advised to seek guidance before attempting this procedure.