How to Remove Car Wheel Arch Clip Fasteners?

1 Answers
ArabellaFitz
07/29/25 11:35pm
Find a flat wooden board or steel plate with high hardness, and insert it into the gap between the door inner panel and the door sheet metal. Move to the position with clip fasteners, apply slight force to pry them up until they detach. Then sequentially pry up all the clip fasteners along the lifted edge.
Was this review help?
11
1
Share
More Forum Discussions

What is the normal high-pressure fuel pressure?

High-pressure fuel pressure normally ranges between 300kpa to 350kpa. It should be noted that fuel pressure may vary depending on the vehicle model. Below is a partial introduction about the fuel pressure sensor: 1. Components: The fuel pressure sensor consists of a printed circuit board, sensor element, spacer block, and housing, among others. It contains a pressure chamber with a diaphragm featuring an overflow valve. The inner side of the diaphragm is a vacuum chamber, which houses a spring. 2. Working principle: Pressure acts directly on the diaphragm of the sensor, causing the diaphragm to produce micro-displacement proportional to the medium pressure. This changes the resistance of the sensor, which is detected by electronic circuits and converted into a standard signal corresponding to this pressure.
9
5
Share

Which car brands use Fuyao Glass?

Domestic automakers such as Ford, Volkswagen, Toyota, Honda, Nissan, and Audi are equipped with Fuyao Glass. Here is extended information: 1. Fuyao Glass: Fuyao Glass is a relatively transparent silicate non-metallic material, with silicon dioxide as its main component. Glass generally has the characteristics of reflecting, absorbing, and transmitting light, along with high chemical stability, acid resistance, and corrosion resistance. 2. Functions: Reduce the frequency of drivers looking down at the dashboard; avoid external distractions to improve reaction speed; free the eyes for a more comfortable and safer driving experience.
5
3
Share

Can a Vehicle Pass the Annual Inspection with a Non-Functional High-Mounted Stop Lamp?

High-mounted stop lamp not working will result in failure of the annual inspection. Below is the relevant information: 1. Brake light positions: Most vehicles are equipped with 3 brake lights - one on each side at the lower rear, plus an additional high-mounted stop lamp on the rear windshield. 2. Brake lights: Some vehicles only have two brake lights, meaning they lack the high-mounted stop lamp. 3. Lighting system: The brake light is a crucial component of the vehicle's lighting system and also one of the most prone to failure. 4. Definition: Vehicle annual inspection refers to mandatory testing required for all vehicles with official license plates and registration certificates, equivalent to an annual physical examination based on motor vehicle safety technical requirements. 5. Purpose: Vehicle annual inspections help promptly eliminate potential safety hazards, encourage better vehicle maintenance, and reduce the occurrence of traffic accidents.
6
0
Share

Is driving at 120 km/h in the far-right lane of the highway considered speeding?

Driving at 120 km/h in the far-right lane of the highway is not considered speeding for small vehicles, but it is considered speeding for large buses and freight vehicles. Below are the specific details regarding road speed limits: 1. Penalty regulations: Exceeding the speed limit by less than 10% results in a warning without fines or penalty points; exceeding by 10%–20% incurs a fine and 3 penalty points; exceeding by 20%–50% incurs a fine and 6 penalty points; exceeding by more than 50% results in a fine and 12 penalty points. 2. Formula for calculating the speeding percentage: (Actual speed / Speed limit – 1) * 100. For example, if the speed limit is 70 km/h and the vehicle speed is 80 km/h, divide 80 by 70, subtract 1, and multiply by 100 to get 14.28, meaning the vehicle is speeding by 14%. If the speed limit is 60 km/h and the vehicle speed is 70 km/h, then 70 divided by 60, minus 1, multiplied by 100 results in a speeding percentage of 16%.
4
4
Share

How many kilometers can you drive in an hour on the highway?

On the highway, you can drive 60-120 kilometers per hour, as the speed should be maintained between 60-120 km/h. The maximum speed must not exceed 120 km/h, and the minimum speed should not be lower than 60 km/h. For small passenger vehicles on the highway, the maximum speed must not exceed 120 km/h, while other motor vehicles should not exceed 100 km/h, and motorcycles should not exceed 80 km/h. Below are specific details about highways: 1. Speed: The design speeds are 80 km/h, 100 km/h, 120 km/h, and 60 km/h (for special sections); 2. Lanes: The road scale consists of at least four lanes in both directions or two lanes in one direction; 3. Definition of a highway: A highway is a type of road classified by technical grade, ranking above Class I, Class II, Class III, Class IV, and unclassified roads. Highways intersect with national or provincial roads in the road network hierarchy, meaning highways can be part of national or provincial roads in the network.
5
0
Share

Is the temporary license plate for a new car handled by the 4S store or by oneself?

4S stores can assist with the process, or you can handle it yourself. Relevant information about temporary license plates: 1. Eligibility and scope for applying for temporary license plates: Temporary license plates have time and regional limitations. You can apply for a temporary license plate at the local vehicle management office if you meet one of the following conditions: when driving the vehicle from the place of purchase to the place of use, you need to apply for a temporary license plate at the vehicle management office in the place of purchase; when transferring the vehicle registration and the official license plate has been surrendered, you need to apply for a temporary license plate at the local vehicle management office to drive back to your locality; if a new car in the local area has not yet obtained an official license plate and needs to be driven to another location for modifications, you need to apply for a temporary license plate locally, and after modifications are completed, apply for a temporary license plate at the local office to drive back to the original area. 2. Materials required for applying for a temporary license plate: The applicant must present a company introduction letter, proof of vehicle origin, certificate of compliance, and other relevant documents (except for the introduction letter, which is kept on file, the rest are returned to the applicant) to the vehicle management office for processing.
6
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.