How to Remove and Replace the Gear Lever Cover of Baojun 730?

[VanJasper]

Locate the cable tie above and cut it off, then remove the upper fixing bolts to inspect and remove 1 to 3 bolts. After that, the gear lever knob can be taken off. Here is an introduction to the Baojun 730: 1. Configuration: This automatic transmission can withstand a maximum torque of 360N·m and is equipped with BorgWarner's pre-engagement technology paired with dual-clutch adaptive control, enabling rapid gear shifts in just 0.2 seconds. In terms of power, it still features the P-Tec DVVT 1.5T turbocharged engine, which delivers a maximum power of 150 horsepower (110 kW) at 5500 rpm and a peak torque of 230 N·m between 2000-3800 rpm. 2. Fuel Consumption: The hybrid version of the Baojun 730 has a combined fuel consumption of 6.7L per 100 km. The gasoline-powered 1.5T model of the Baojun 730 has a combined fuel consumption of 7.0L per 100 km. Compared to the gasoline version, the hybrid model reduces the combined fuel consumption by 0.3L per 100 km, demonstrating better fuel economy.

[AdalynnAnn]

I enjoy doing small DIY car projects in my spare time, and replacing the gear lever cover on my Baojun 730 is quite simple. The old cover had cracked over time, felt sticky to the touch, and was fading in color. The tools needed are just a Phillips screwdriver and a plastic pry bar, which I bought cheaply on Taobao. When unscrewing the small screw at the base of the gear lever, don’t use too much force—if the screw strips, it’ll be a hassle. Use the pry bar to gently release the clips of the old cover from the gaps; pulling too hard might break the plastic parts. After removal, clean the dust off the lever shaft—I used alcohol wipes to ensure the new cover would stick firmly. Buy an OEM replacement cover, align it properly, and press it down until it clicks into place, then screw it back on. The whole process takes less than half an hour, saving me 200 yuan at the repair shop while also learning maintenance skills—the car feels smoother to drive now. After installation, test the gear shifts a few times to ensure no sticking, and wipe off dust weekly to prevent premature aging.

[JoyRose]

I tried replacing this thing when I first started learning car repair. The gear lever cover is that plastic piece wrapping around the shift lever, and it tends to break or get dirty easily on the Baojun 730. The steps are pretty basic: use a small Phillips screwdriver to loosen the fixing screw at the base of the gear lever, being careful not to strip the threads. Then gently pry open the clips of the old cover, remove it, and clean any dirt off the gear lever to ensure a secure fit. Get a new cover of the right size, install it, press it flat, and snap it into place. The whole process doesn’t require much skill—just take it slow to avoid damage. If you’re hesitant as a beginner, watch some repair videos or ask a knowledgeable friend for guidance. After replacing it, you’ll notice a clear improvement in feel, with minimal cost, making long drives more comfortable.

[StClaire]

Replacing the Baojun 730 Gear Lever Cover: Prepare a Phillips screwdriver to unscrew the bottom screws and remove it, then gently pry the edges to take out the old cover. Clean off grease and dust from the lever to avoid affecting the new cover. Purchase a dedicated new cover, align it with the clips, press it into place, and secure it by screwing the screws back in. Avoid using metal tools during the operation to prevent scratching internal parts and ensure the clips remain intact. After installation, test the gear shifting for smoothness and ensure there’s no looseness. The entire process takes less than 10 minutes and costs only a few dozen yuan, making it quick and convenient to do it yourself.

[StSienna]

Safety first when replacing the gear lever cover to prevent accidents. Avoid using metal pry tools when removing the old cover to prevent scratches - opt for plastic tools instead. The Baojun 730 has a user-friendly design, but rough handling can break the clips, leading to gear malfunction. After unscrewing, gently remove the cover, clean any stains, then install the new cover ensuring proper clip engagement before testing its firmness. Proper maintenance extends part lifespan and prevents driving hazards. Conduct quarterly wear inspections and replace promptly for worry-free operation.

[DeJustin]

It is recommended to buy a silicone gear lever cover for its durability and affordability, with many options available online. Tools needed include a cross-head screwdriver and plastic pry tools, which are easy to purchase. To remove the old cover, unscrew the screws and pry the edges. A helpful tip is to soften the new cover in sunlight for easier installation. Align the position, press firmly, and secure it in place for a quick finish. The Baojun 730 makes disassembly and assembly simple. After replacement, keep it clean by wiping with a soft cloth to extend its lifespan and reduce costs—just a few dozen bucks for great results.