How to Remove and Install the Steering Wheel of Baojun 730?

3 Answers
HannahRose
07/29/25 3:05am
Method for removing and installing the steering wheel of Baojun 730: After turning off the engine, switch off all electrical appliances, turn the steering wheel 90 degrees, locate the holes on the back of the steering wheel, poke them with an appropriate tool, then return the steering wheel to its original position. Turn the steering wheel 90 degrees in the opposite direction and poke the other holes, and the airbag assembly will come off. Remove the screws to take out the airbag, then unscrew the steering wheel screws to remove the steering wheel. Precautions during removal and installation: When tapping, pass your left hand upward from under the steering wheel to hold the screw rod, lift the steering wheel upward with your left arm, or sit in the driver's seat, lean the seat forward, support the steering wheel with both legs, and use a hammer in your right hand to tap the top of the screw rod. The Baojun 730 is equipped with a 1.5T 147 horsepower L4 engine and a 6-speed manual transmission, with a maximum engine power of 108kW and a maximum torque of 250Nm. The dimensions of the Baojun 730 are 4780mm in length, 1780mm in width, and 1740mm in height, and it features a 5-door, 7-seat MPV body structure.
Was this review help?
17
2
Share
FernandoFitz
08/12/25 1:25pm
Last time I disassembled and reassembled the steering wheel of my Baojun 730 myself, and the overall experience was decent, but safety details must be noted. First, remember to disconnect the battery's negative terminal to prevent accidental airbag deployment—I usually wait 15 minutes before starting. Then, there's a plastic cover behind the steering wheel; pry it open with a screwdriver to reveal the screws securing the airbag. After removing the screws, carefully take out the airbag module and set it aside. Loosen the nut at the center of the steering wheel; a standard 19mm wrench should suffice for most models. When pulling the steering wheel, you might encounter slight resistance—a few gentle taps can help loosen it, but avoid forcing it to prevent damage. Once all electrical connectors are unplugged, the steering wheel can be removed. For reinstallation, reverse the steps, ensuring precise alignment with the original position—misalignment can affect steering accuracy while driving. I found taking photos of the original setup very helpful to avoid mistakes. Disassembling the steering wheel is mainly for modifications or repairs, such as fixing broken buttons, which can save hundreds of dollars. However, the risks are significant—beginners might accidentally cut wires or misalign the airbag system. I recommend watching online tutorials first, and if unsure, visiting a repair shop is safer. After all, safety comes first.
Was this review help?
7
4
Share
Expand All
DePresley
10/02/25 5:21am
Removing the steering wheel is no trivial task and requires careful step-by-step operation. First and foremost, I emphasize safety: after parking and turning off the engine, immediately disconnect the negative terminal of the battery and wait sufficient time for the system to discharge—otherwise, the airbag could malfunction. The removal process for the Baojun 730 is similar to most vehicles: remove the rear cover, then unscrew the airbag bolts (typically requiring Torx tools—ensure the correct size is used). When loosening the center nut on the steering wheel, keep the wrench steady to avoid stripping the threads. After removing the steering wheel, disconnect all wiring harnesses carefully to prevent damage from pulling. During reinstallation, remember to tighten the nut and reset the airbag properly. Finally, check if the steering angle sensor is aligned correctly—misalignment can affect turn signal functionality. The entire process may take 30 minutes to an hour. Based on my experience, I recommend proceeding only with all necessary tools prepared. However, beginners often make mistakes, such as improperly connecting wiring harnesses, which can lead to horn failure. Hiring a professional is also a cost-effective option—it's affordable, safe, and hassle-free. Remember: the steering system is critical to driving stability—don’t compromise safety to save money.
Was this review help?
4
2
Share
Expand All
More Forum Discussions

What is the fuel tank capacity of the Crown?

The fuel tank capacity of the Crown is 70L. Fuel tanks can be divided into two types: open and closed. They must have sufficient volume. To maintain oil cleanliness, the tank should have a sealed cover plate with an air filter installed. The bottom of the tank should be at least 150mm above the ground, and full attention should be paid to the anti-corrosion treatment of the inner surface of the tank. The Crown has dimensions of 5020mm in length, 1805mm in width, and 1480mm in height, with a wheelbase of 2925mm and a fuel tank capacity of 70L. This vehicle is equipped with a 2.0T turbocharged engine, delivering a maximum power of 173 kW and a maximum torque of 350 Nm, paired with an 8-speed automatic transmission.
16
5
Share

Why is the Ford Mondeo's water temperature high?

Ford Mondeo's high temperature may be caused by: 1. Cooling fan: The cooling fan is not rotating or has malfunctioned. 2. Cooling medium: Issues with the cooling medium, such as depleted coolant, leading to excessive temperature in the car's radiator. 3. Thermostat: A damaged thermostat; this issue requires sending the car to a 4S shop for repair. 4. Radiator: Radiator malfunction, which may require replacing the radiator water or the entire radiator. Solutions for high engine radiator temperature: 1. Stop and wait: Pull over to a safe area, set up a warning sign, open the engine hood, and turn off the engine. 2. Cool down: Wait for a period until the engine's water temperature has sufficiently decreased before checking the engine's cooling water level.
13
4
Share

What to Do When There's a Bad Smell When Turning on the Car Air Conditioner?

Solutions for bad smells when turning on the car air conditioner include: 1. Replace the air filter: The air filter is often overlooked. A dirty filter not only fails to perform its original function but also causes secondary pollution to the air entering the car. 2. Clean the air ducts: Regularly replacing the filter can keep dirty air outside, but for vehicles used for a long time, dust and mold may still accumulate in the air conditioning system. In this case, an air duct cleaner is needed. The car air conditioner is an air conditioning device installed in the car, capable of cooling, heating, ventilating, and purifying the air inside the cabin, providing a comfortable environment for passengers, reducing driver fatigue, and improving driving safety.
9
5
Share

How to Read the Fuel Gauge on Honda CR-V?

To check the fuel gauge on a Honda CR-V, start the engine and observe the position of the fuel gauge needle on the right side. When the tank is full, the needle will point to the blue area. Generally, when it approaches the red line, it indicates that the fuel is nearly empty. The fuel gauge only provides an approximate reading. The functions of the fuel gauge are as follows: 1. Function one: The fuel gauge indicates the amount of fuel remaining in the car's fuel tank, which can be displayed via a pointer or digital readout. 2. Function two: The fuel gauge consists of a fuel level indicator with a voltage regulator and a fuel level sensor. 3. Function three: The low fuel warning light activates when the fuel level in the tank drops below a specified threshold, alerting the driver to refuel.
12
3
Share

What does the L gear in the Fit mean?

The L gear in the Fit stands for Low gear, primarily used when driving on slopes. This gear is equivalent to the first gear in a manual transmission car. During long downhill descents, it keeps the car in a lower gear, eliminating the need for prolonged braking. By maintaining the transmission in a lower gear, it utilizes engine braking to slow down the vehicle. The Fit is a compact sedan produced by GAC Honda. The dimensions of this car are 4109mm in length, 1694mm in width, and 1537mm in height, with a wheelbase of 2530mm. It features a MacPherson strut independent front suspension and a torsion beam non-independent rear suspension.
7
5
Share

How to Remove the RPM Protection on the Touareg?

The method to remove the RPM protection on the Touareg requires a computer refresh and upgrade, which must be handled by professionals at a 4S dealership. The Touareg is a mid-to-large-sized SUV, featuring interior design elements with very straight and flat lines, inspired by the CrossBlue concept car. It also comes with a three-spoke flat-bottom steering wheel and a 12.3-inch full LCD instrument panel. The vehicle is equipped with a multimedia information display screen using the AppConnect mobile phone interconnection platform, supporting Apple CarPlay and Android Auto. Additionally, it features adaptive cruise control, lane keeping, blind spot monitoring, collision warning, heated steering wheel, front seat heating, and a panoramic sunroof, among other functions.
10
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.