How to Remove and Install the Headlight Assembly of the Excelle?

1 Answers
LylaFitz
07/23/25 11:37pm
After opening the hood, there is an iron hook on the inner side of both headlights. At the back of the headlight, there is a plastic screw used to lock the headlight in place. Unscrew the two plastic screws at the back of the headlight, store them safely, then pull the iron hook outward to its limit to remove the headlight. Once the headlight is removed, you will notice it is held by the headlight wiring harness at the back, which is secured by a clip. Locate the clip, press it down, and you can then disconnect the wiring harness. After disconnecting the wiring harness, the car's headlight assembly can be completely removed.
Was this review help?
1
2
Share
More Forum Discussions

Where is the OBD port on the Touran?

Location of the Volkswagen Touran OBD interface: It is located behind the plastic cover under the steering wheel. First, open the driver's glove box, then remove the glove box, and you will see the OBD interface on the right side behind the glove box. Here is some related information about OBD: 1. OBD is the abbreviation for On-Board-Diagnostic, which translates to "On-Board Diagnostics" in Chinese. This system continuously monitors the engine's operating conditions and the working status of the exhaust after-treatment system. If it detects any situation that may cause excessive emissions, it will immediately issue a warning. 2. When a fault occurs in the system, the Malfunction Indicator Lamp (MIL) or Check-Engine warning light will illuminate. At the same time, the OBD system will store the fault information in the memory. The relevant information can be read in the form of fault codes through standard diagnostic tools and interfaces. Based on the fault codes, maintenance personnel can quickly and accurately determine the nature and location of the fault.
2
5
Share

Where is the ESP switch of Audi A6L?

The ESP switch of the Audi A6L is located below the air conditioning screen on the center console. The ESP can be temporarily turned off under the following circumstances: 1. When the vehicle is stuck in mud. The ESP system reduces engine torque, which can exacerbate wheel slippage. 2. During extreme driving. Actions such as drifting around corners or performing a launch start require a certain degree of slippage, making it necessary to turn off the ESP. 3. On roads with deep snow. On slippery snow-covered roads, the tires already have insufficient grip. If the ESP continues to intervene, it will only cause the wheels to sink deeper. However, when the snow is just beginning to melt, remember not to turn off the ESP, as this could lead to even more severe slippage. 4. When snow chains are installed on the tires. Changes in the tire's outer diameter may cause the sensors to mistakenly interpret this as a tire malfunction, leading the ESP to continuously issue warnings, which can affect driving.
8
5
Share

Can vehicle inspection be done in another city?

Vehicle inspection can be done in another city. More information about vehicle inspection in another city is as follows: 1. The most important document for vehicle inspection in another city is the Power of Attorney for Vehicle Inspection in Another City. When you need to have your vehicle inspected in another city, the first step is to obtain this Power of Attorney. Then, take the Power of Attorney along with the relevant inspection documents to the vehicle management office in the designated city to process the vehicle inspection. To apply for the Power of Attorney for Vehicle Inspection in Another City, you need to bring the vehicle owner's ID card, vehicle license, vehicle insurance documents, original and photocopy of the vehicle and vessel tax, and an application for cross-region inspection to the vehicle management office in the registration city. 2. For the vehicle inspection, you need to bring the vehicle license, vehicle insurance documents, and the Power of Attorney for Vehicle Inspection in Another City to the vehicle management office in the designated city. During the inspection process, it is important to note that the vehicle must not have any outstanding traffic violations, otherwise, the normal inspection cannot be conducted.
15
5
Share

Where is the Car's Charcoal Canister Located?

Automobile charcoal canister is located between the car engine and the fuel tank. Here are the relevant details about the charcoal canister: 1. Function: When the engine is running and the solenoid valve is activated, the engine draws fuel vapor from the fuel tank and the vapor adsorbed by the active material into the intake manifold. When the engine is not running or the solenoid valve is not activated, the vapor from the fuel tank enters the charcoal canister and is absorbed by the active material. 2. Working Principle: When the engine is running and reaches medium to high speed, the solenoid valve is energized, opening the pipeline. The vacuum in the engine's intake manifold then draws the combustible gas from the charcoal canister into the cylinders to participate in combustion. Simultaneously, external air enters the charcoal canister through the breathing hole, flows through the internal absorption layer, mixes with the fuel to form combustible gas, and then flows into the engine's intake pipe. During this process, the activated charcoal in the canister is gradually restored due to the suction effect of the engine.
16
1
Share

Why does the engine warning light come on after an oil change?

There are many reasons why the engine warning light comes on after an oil change. The causes of the warning light coming on include the following: 1. Oil type: Engine oils produced by different manufacturers cannot be mixed. When changing to a different brand of engine oil, the engine should be cleaned to prevent the old and new oils from reacting and affecting the oil quality. If the old oil is not completely drained and is incompatible with the new oil, it may cause the warning light to come on. 2. Residual old oil: If the residue from the old oil is not thoroughly cleaned, the new oil may not last long, clogging the oil filter and causing the warning light to come on. Changing the oil filter during the oil change can also eliminate the factors that cause the warning light to come on. 3. Oil filter: Some oil filters are of poor quality and have inadequate oil filtration performance. Replacing the oil filter during the oil change can also eliminate the phenomenon of the warning light coming on.
8
0
Share

What is the curb weight of the Mazda CX-30?

Mazda CX-30 has a curb weight of 1450kg. Here is an introduction to the features of the Mazda CX-30: Distinctive exterior design: The Mazda CX-30 is built based on the "KODO 2.0" design philosophy. The front face of the new car adopts Mazda's latest family design, with eagle-eye headlights that deliver a strong visual impact. Comfortable and shock-absorbing: The CX-30's butterfly-shaped bionic non-independent suspension can effectively suppress bouncing when passing over speed bumps and uneven roads, ensuring both comfort and safety. Appearance: The Mazda CX-30 was officially unveiled at the 2019 Geneva Motor Show. The model follows the KODO design philosophy and will be equipped with engines from the Skyactiv-G, Skyactiv-D, and Skyactiv-X series.
19
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.