How to Remove and Install the Air Filter for the New Mondeo

1 Answers
AxelLynn
07/23/25 8:22pm
The air filter for the new Mondeo is located inside the glove box. The removal method mainly involves the following steps: 1. First, remove the side cover. 2. Then, remove the vent trim panel. 3. Next, unscrew the bolts and take off the glove box. 4. After removing the glove box, the air filter is located inside the cover panel, and the blower is below. There are two cross screws on the right side of the cover panel; use a screwdriver to remove them. 5. After removal, the air filter can be pulled out directly by pinching it. Additional information: The removal method for the older Mondeo's air filter is: 1. First, remove the accelerator pedal. 2. On the right side of the accelerator pedal, there is a black cover, inside which is the air filter. 3. Use a small screwdriver to remove the cover panel.
Was this review help?
10
4
Share
More Forum Discussions

What is the ideal tire pressure for the Nissan X-Trail?

The standard tire pressure for the Nissan X-Trail ranges between 2.4-2.5 bar. Seasonal factors may influence this, with winter tire pressure appropriately increased by 0.2 bar and summer pressure reduced by 0.1 bar. These figures comply with the international GBT2978-2008 standard. Higher-end models of the Nissan X-Trail come equipped with a tire pressure monitoring and alert system, which displays real-time tire pressure data on the dashboard while driving. For other models, external instruments are required to check tire pressure, and it is advisable to inspect both tire condition and pressure before long-distance trips. Generally, a tire pressure exceeding 2.8 bar is considered too high, while a pressure below 2.0 bar is too low. Hazards of overinflation: Reduced tire friction and adhesion, impairing braking effectiveness; increased steering wheel vibration and drift, diminishing ride comfort; accelerated wear on the central tread pattern, shortening tire lifespan; heightened vehicle vibration, indirectly affecting other components' longevity; excessive stretching of tire cords, reducing elasticity and increasing driving load. Hazards of underinflation: Increased friction coefficient with the road surface, raising fuel consumption; heavier steering and drift, compromising driving safety; amplified movement across tire sections, causing abnormal heat from excessive rolling; degradation of cord and rubber functionality, leading to delamination, cord breakage, or rim friction damage; multiplied ground friction, rapidly escalating tire temperature and softening, drastically reducing strength. High-speed driving may result in tire blowouts. If the tire pressure monitoring indicator illuminates (a yellow symbol featuring an irregular circle without a seal, four small spikes below, and an exclamation mark inside), it typically indicates one of three causes: Abnormal tire pressure: Usually triggers an alert below 1.8 bar or above 3.0 bar, necessitating immediate inspection and adjustment. Unreset tire pressure monitoring: Failure to reset the system after inflation retains outdated data, causing the light to stay on. A simple reset resolves this issue. Damaged tire pressure sensor: Mounted internally and connected to the tire valve, physical impact can damage the sensor, requiring replacement to extinguish the warning light.
12
2
Share

What is the curb weight of Hafei minivans in kilograms?

There are a total of 5 models of Hafei minivans, with the following curb weights: Junyi 1.0L Basic M10R has a curb weight of 1095kg, Luzun Dabawang 1.3L Standard has a curb weight of 1265kg, Minyi 1.0L Basic DA465Q has a curb weight of 985kg, Hafei Xiaobawang 1.0L Economy D10 has a curb weight of 1045kg, and Zhongyi V5 2013 1.3L Comfort M13R's curb weight is not available on the 58 Auto official website as it has been discontinued. Below are the detailed specifications for each model: Junyi 1.0L Basic M10R: Overall dimensions 4025mm*1645mm*1910mm, equipped with a 1.0L naturally aspirated engine, maximum horsepower 75Ps, maximum power 55kW, maximum power speed 6000rpm, maximum torque 84Nm, maximum torque speed 4500rpm, fuel supply method is multi-point electronic injection, matched with a manual transmission (MT), front suspension uses MacPherson independent suspension, rear suspension uses leaf springs. Luzun Dabawang 1.3L Standard: Overall dimensions 4180mm*1695mm*1875mm, equipped with a 1.3L naturally aspirated engine, maximum horsepower 79Ps, maximum power 58kW, maximum power speed 5400rpm, maximum torque 108Nm, maximum torque speed 5400rpm, fuel supply method is multi-point electronic injection, matched with a manual transmission (MT), front suspension uses MacPherson independent suspension, rear suspension uses leaf springs. Minyi 1.0L Basic: Overall dimensions 3735mm*1510mm*1890mm, equipped with a 1.0L naturally aspirated engine, maximum horsepower 48Ps, maximum power 35.5kW, maximum power speed 5000rpm, maximum torque 74Nm, maximum torque speed 3000-3500rpm, fuel supply method is multi-point electronic injection, matched with a manual transmission (MT), front suspension uses MacPherson independent suspension, rear suspension uses longitudinal leaf spring non-independent suspension. Hafei Xiaobawang 1.0L Economy D10: Overall dimensions 3948mm*1525mm*1855mm, equipped with a 1.0L naturally aspirated engine, maximum horsepower 48Ps, maximum power 35.5kW, maximum power speed 5000rpm, maximum torque 74Nm, maximum torque speed 3000-3500rpm, fuel supply method is multi-point electronic injection, matched with a manual transmission (MT), front suspension uses MacPherson independent suspension, rear suspension uses longitudinal leaf springs. Zhongyi V5 2013 1.3L Comfort M13R: Overall dimensions 4000mm*1625mm*1880mm, equipped with a 1.3L naturally aspirated engine, maximum horsepower 100Ps, fuel supply method is multi-point electronic injection, matched with a manual transmission (MT).
17
5
Share

What is the normal tire pressure for the new Verano?

The standard tire pressure range for the new Verano is 2.4-2.5bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2bar in winter and decreased by 0.1bar in summer. This data is based on the international GBT2978-2008 standard requirements. The new Verano is equipped with an active tire pressure monitoring function, allowing you to check the specific tire pressure values on the dashboard. The operation method is: press the left-marked button on the right side of the steering wheel; scroll up and down to select the information bar and press the checkmark; then scroll down to find the tire pressure monitoring information. Generally, a tire pressure above 2.8bar is considered too high, and a tire pressure below 2.0bar is considered too low. Hazards of overinflated tires: Reduced tire friction and adhesion, affecting braking performance; causing steering wheel vibration and deviation, reducing driving comfort; accelerating wear on the central tread pattern of the tire, reducing tire lifespan; increased body vibration, indirectly affecting the lifespan of other components; excessive stretching deformation of tire cords, reducing tire elasticity, and increasing the load on the car while driving. Hazards of underinflated tires: Increased friction coefficient with the road surface, leading to higher fuel consumption; causing heavy steering and deviation, posing safety risks; increased movement of tire parts, leading to abnormal heat generation due to excessive rolling; reduced functionality of cords and rubber, causing delamination or cord breakage and excessive friction with the rim, leading to damage and abnormal wear; multiplied friction between the tire and the ground, sharply increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may lead to tire blowouts. If the tire pressure monitoring indicator light comes on (a yellow symbol, an irregular circle with no stamp on top and four small spikes at the bottom, with an exclamation mark inside), there are generally three reasons: Abnormal tire pressure: Typically, an alarm is triggered when the pressure is below 1.8bar or above 3.0bar. In this case, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset in time, the system will still record the previous data, causing the tire pressure monitoring indicator to light up. Simply reset the tire pressure to resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, used to monitor tire pressure, is installed inside the tire and connected to the tire inflation port. If the sensor is damaged during driving, the tire pressure warning light will come on. In case of sensor damage, only a replacement with a new part can solve the problem.
7
0
Share

What are the vision requirements for motorcycle physical examinations?

Motorcycle physical examination vision requirements mainly include: 1. Applying for a motorcycle driver's license renewal: A physical condition certificate must be submitted. 2. Applicants for motorcycle driving license categories: The naked or corrected vision of both eyes must reach 4.9 or above on the logarithmic visual acuity chart. Here are some additional details: 1. If a driver is required to undergo an annual physical examination but fails to do so within one year, their driver's license will be revoked. 2. The physical examination standards for applying for a motor vehicle driver's license require active cooperation with physicians during the physical examination.
9
5
Share

What is a Joystick?

Joystick is a physical device that converts the movement of a plastic rod into electronic information that a computer can process. The basic principle of a joystick is to transform the motion of the plastic rod into electronic signals comprehensible to computers. Its operation varies according to required speed conditions. Below are detailed explanations: Function of the joystick: Its primary function is to shift gears and change speed based on driving conditions. On the other end of the electric motor, its rotating shaft is connected to the joystick's position sensor (such as a potentiometer or optical sensor). Whenever the joystick moves, whether caused by the motor or the player, the sensor can detect the joystick's position.
3
0
Share

Will Forcibly Turning a Locked Steering Wheel Cause Damage?

Forcibly turning a locked steering wheel can cause damage. Below is an introduction to steering wheel lock: 1. Introduction: Steering wheel lock is a simple anti-theft feature. After the car is turned off, rotating the steering wheel from its centered position to one side (usually to the left) by a certain angle will cause the steering wheel to emit a "click" sound and lock. In the locked state, the steering wheel cannot be turned, the key cannot be turned, and the car cannot be started, thereby achieving the anti-theft function. 2. Unlocking Method: Hold the steering wheel with your left hand and gently shake it while simultaneously shaking and turning the key with your right hand to unlock it.
16
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.