How to Remove a Wheel?

What are the tips for reversing into the garage in Subject 2?

Tips for reversing into the garage: After getting into the car, the driver should first adjust the seat and rearview mirrors, fasten the seat belt, then shift the car into reverse gear, release the parking brake lever, and start reversing at idle speed. The driver observes the garage through the right rear window. When the black edge of the right rear window aligns with the right boundary line of the garage, turn the steering wheel steadily to the right to the limit position. After the car enters the garage, the driver should look back at the left rearview mirror. When the entire left boundary line of the garage appears, immediately straighten the steering wheel. When the left door handle is level with the bottom line of the garage as seen in the left rearview mirror, stop immediately. Points deduction items for reversing into the garage are as follows: Not following the prescribed route or sequence, deduct 100 points; vehicle body crossing the line, deduct 100 points; failing to reverse into the garage, deduct 100 points; stopping midway, deduct 100 points. Subject 2 has a full score of 100 points, with evaluation criteria set for failing, deducting 20 points, deducting 10 points, and deducting 5 points. The test is passed if the following conditions are met: ① For applicants of large buses, tractors, city buses, medium buses, and large trucks, a score of 90 or above is required; ② For other vehicle types, a score of 80 or above is required.

9

0

Share

What to Do When a Car Stalls in Water?

Turn off the engine, activate the hazard warning lights, promptly call for rescue, and move to a safe place to wait for assistance. There are generally three reasons why a car suddenly stalls while driving: Electrical Circuit Failure: The car stalls due to low-voltage power interruption during driving. In this case, you can primarily check the ignition and starter switches, as well as the fuse box. Low-Voltage Circuit Short Circuit Causing Stall: In this situation, the car stalls intermittently. Inspect the car's low-voltage circuits. Component Failure: This issue is usually related to the ignition coil, capacitor, or electronic ignition module. The car may start initially but stall after a while, then start again and stall once more.

1

3

Share

What to Do When the Blower Makes Abnormal Noises?

The solution to abnormal noises from the blower is to remove foreign objects and troubleshoot the issue. There are generally three scenarios of blower noise, with specific solutions as follows: Noise changes with airflow volume: This situation is most likely caused by foreign objects inside the blower, and removing them should resolve the issue. If the noise persists after cleaning, it's necessary to disassemble the blower to inspect the specific cause of the fault. Resonance noise from airflow in the ducts: Turn off the air conditioning compressor, turn on the blower, and adjust the airflow volume and direction. Foreign objects in the air ducts or motor failure: First, turn off the air conditioning compressor, turn on the blower, and adjust the airflow volume and direction. If the noise changes or diminishes accordingly, it indicates foreign objects in the air ducts. If not, and the noise only occurs when adjusting the airflow volume and direction, it is likely a motor failure or other issues. Open the engine compartment for a detailed inspection and proceed with disassembly and repair as needed.

7

3

Share

What does the P indicator on the car mean?

When the dashboard displays a P, it indicates that the parking brake is engaged. The parking brake, commonly referred to as the handbrake, is a manually operated brake installed in motor vehicles. It is used to stabilize the vehicle after it has come to a complete stop, preventing accidents caused by rolling on inclined surfaces. Here is a detailed introduction to the parking brake: Working principle of the parking brake: Mechanical handbrakes operate via a cable or similar mechanism that connects to the rear brake calipers. When the handbrake is engaged, the calipers press against the brake pads, thereby achieving the parking function. Electronic handbrakes, on the other hand, use an electric motor to drive the cable or similar mechanism, which then engages the rear brake calipers to press the brake pads and achieve the parking function when the parking switch is activated. Parking brakes can be categorized by operation method into two types: Hand-operated parking brakes and foot-operated parking brakes. By control method, they are divided into two types: mechanically controlled parking brakes and electronically controlled parking brakes. To engage the parking brake, press the brake pedal down and fully pull out the parking brake lever. To release the parking brake, press the brake pedal down, slightly pull the parking brake lever upward, press the button on the handle end with your thumb, and then lower the parking brake lever back to its original position.

10

3

Share

Is the driver's license photo the one submitted during registration?

Is the driver's license photo the one submitted during registration? The following are the details: Photo submission during driving school registration: When registering at a driving school, you need to provide photos and digital photos. Among the submitted photos, there is an archive photo, which is the driver's license photo. The submitted one-inch photo includes an archive photo that will be affixed to the driver's license. Generally, it should be a one-inch, white-background, bareheaded photo. Driver's license photo requirements: The photo must be a recent (within 6 months) front-facing, bareheaded, color, single-person, half-length small one-inch photo of the driver's license applicant. The photo size should be 3.2cm*2.2cm, with a head length of 1.9cm to 2.2cm and a head width of 1.4cm to 1.6cm, on a white background. No uniforms are allowed in the photo, and the image must be clear and natural.

18

5

Share

How Many Kilograms Does 1 Liter of Gasoline Equal?

According to the density of each substance, 1 liter of gasoline is approximately equal to 0.72~0.75 kilograms. Because according to the measurement units, 1 kilogram equals 1 kilogram. So we convert 1 liter to 1000 milliliters for calculation. The density of commonly used 92-octane gasoline in daily life is about 0.725g/ml, while 95-octane gasoline is 0.737g/ml. The calculation shows that 1 liter of 92-octane gasoline is approximately 0.725 kilograms, and 1 liter of 95-octane gasoline is about 0.737 kilograms. The mass density formula m=V can be used to determine how many kilograms 1 liter of gasoline equals. Gasoline density: The average density of 90-octane gasoline is 0.72g/ml, so the mass of 1 liter of 90-octane gasoline is 0.72 kilograms. The density of 93-octane gasoline is 0.725g/ml, so the mass of 1 liter of 93-octane gasoline is 0.725 kilograms. The density of 97-octane gasoline is 0.737g/ml, so the mass of 1 liter of 97-octane gasoline is 0.737 kilograms.

9

4

Share

How to Remove a Wheel?

What are the tips for reversing into the garage in Subject 2?

What to Do When a Car Stalls in Water?

What to Do When the Blower Makes Abnormal Noises?

What does the P indicator on the car mean?

Is the driver's license photo the one submitted during registration?

How Many Kilograms Does 1 Liter of Gasoline Equal?

How to Clean Gasoline Effectively?

What are the distinctive features of a machine-made teapot?

How long after obtaining a C1 driver's license can you apply for a B2 driver's license?

Are Japanese Cars Left-Hand Drive or Right-Hand Drive?