How to Remotely Start the Lynk & Co 03?

1 Answers
LilyMarie
07/30/25 7:11am
To remotely start the Lynk & Co 03, follow these steps: 1. Search for 'Lynk & Co' in the app store, then download and install the Lynk & Co app. 2. Register and log in to the app using your phone number and associate your vehicle. 3. Turn on Bluetooth to connect the vehicle. 4. Follow the prompts on your phone to remotely start the vehicle. 5. During the starting process, the yellow turn signals will flash three times. Once the engine starts, the white daytime running lights will remain on. 6. To drive the vehicle, press the start button while stepping on the brake. At this point, the vehicle can be shifted into gear and driven normally.
Was this review help?
9
5
Share
More Forum Discussions

What Causes the Remote Key Failure in the New Excelle?

New Excelle remote key failure may be due to remote control issues or signal problems. Specific causes of failure: The remote may be too far from the vehicle; the remote battery may be dead or low on power; there may be other vehicles or obstacles blocking the signal; repeatedly operating the remote outside its range may require resynchronization; if the central locking control system is overloaded due to repeated operations in a short period, the power may be temporarily cut off; it may be affected by external radio signal interference. Solutions: There may be signal interference nearby, eliminate the interference; the remote key may be out of battery, replace the battery; the remote key circuit may be damaged, requiring a replacement.
15
1
Share

Where is the diagnostic connector of Haval H3?

The diagnostic connector of Haval H3 is located in the interior trim panel below the steering wheel, near the driver's knee area. Pin configuration of automotive diagnostic connector: Pin 16 is positive power supply, pin 4 is ground, pin 7 is the data diagnostic line (typically for engine testing). Other pins serve as data diagnostic lines for various vehicle functions including ABS system, airbag system, automatic transmission system, etc. Working principle: Features manual fault code reading and clearing functions. Compact design for portability, simple operation, and high cost-effectiveness. Specifically designed for vehicle owners or drivers with precise compatibility. Users connect this device to the vehicle's diagnostic port, then manually operate its buttons to read or clear fault codes from the electronic control systems.
14
2
Share

What colors are available for the Volkswagen Sagitar?

The Volkswagen Sagitar is available in the following colors: Persian Gray, Elegant Silver, Candy White, Polar White, Deep Black, Triumph Gold, Maya Red, and Peacock Blue. Taking the 2019 Volkswagen Sagitar as an example, its body dimensions are: length 4753mm, width 1800mm, height 1462mm, with a wheelbase of 2731mm and a fuel tank capacity of 50 liters. The 2019 Volkswagen Sagitar features a front MacPherson independent suspension and a rear multi-link independent suspension. It is equipped with a 1.2T turbocharged engine, delivering a maximum horsepower of 116PS, a maximum power of 85kW, and a maximum torque of 175Nm, paired with a 5-speed manual transmission.
9
4
Share

What is the reason for gear shifting jerking in Audi A6L?

Audi A6L gear shifting jerking is caused by the mismatch between vehicle speed and gear position. Reasons for jerking sensation when shifting gears in automatic transmission: Transmission clutch pressure leakage; Transmission oil circuit blockage or poor flow; Transmission oil not filled to the standard level; Solenoid valve damage. Reasons for transmission jerking: Transmission control system failure, leading to severe gear shifting impact, which requires diagnosis with a diagnostic computer to determine the fault. Issues with the car's transmission itself. Excessive impurities and dirt inside the car's transmission affect its normal operation, resulting in the jerking sensation. Gear shifting: Gear shifting (changing gears) refers to the transmission, which is used to change the torque and speed of the engine crankshaft to meet the different needs of driving wheel traction and speed under various driving conditions such as starting, accelerating, driving, and overcoming various road obstacles.
7
4
Share

What is the situation of insufficient fuel supply in Audi A4?

Decreased performance of the oil pressure switch or deterioration of oil quality, reduced viscosity, leading to insufficient oil. Insufficient transmission fluid: Insufficient transmission fluid in Audi A4 may result in difficulty starting, hard and rough gear shifting, and vehicle jerking during gear changes. Friction on the gear surfaces can cause scratches, making gear shifting rough or even impossible, causing significant damage to the transmission, though not dangerous. Automotive oil products: Because the original transmission fluid is designed based on the technical specifications of the car's transmission, using such fluid can maintain the transmission's good mechanical performance and extend its lifespan. At the same time, transmission fluid plays a role in lubrication, cleaning, and cooling within the transmission.
17
2
Share

What are the methods to identify a flood-damaged car?

Identifying a flood-damaged car involves the following methods: 1. Carefully inspect the interior and flooring. If there are mismatches or looseness, they were likely replaced. Discolored, stained, or faded materials usually show signs of water damage. 2. Test the power and electronic devices multiple times, such as interior and exterior lights, windows, door locks, radio, cigarette lighter, heater, and air conditioning, to ensure they function properly. 3. Check the trunk, glove compartment, dashboard, and under the seats for signs of water damage, such as mud, sludge marks, or rust in hidden areas. 4. Turn the ignition key to verify that all related accessories, warning lights, and gauges work properly, and ensure the airbag and ABS indicator lights function correctly.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.